RS Securit 7 User manual

Introduction

The Securit 7 is a microprocessor controlled intruder alarm

panel. It features seven zones of which five are programmable

and two dedicated to entry/exit and personal attack. A non-

volatile memory holds the programming options and the 18

event log. These will be retained even in the event of total

power loss. The panel utilises a blind control box, remote

programming and control keypad. The system is designed to

be simple to program and allow flexibility in use.

Note: Before proceeding with installation read this document

thoroughly.

System planning

To enable the installation to proceed smoothly it is best to plan

the work before you begin. Start by drawing a plan of the

building to be protected (see figures 1 and 2). You will need to

divide the building into zones. Zone 1 is always used as the

final exit zone with the securit 7 panel.

The system layouts shown are a guide to typical positions of

the system components. This will obviously vary depending on

the premises and the level of protection to be afforded.

However, the general rules given cover all installation layouts.

General rules

1. Final exit doors should have magnetic contact switches

fitted to ensure that the premises cannot be vacated with

the doors left open and also to protect against forced entry.

2. PIR detectors are best fitted where an intruder has to pass

through an area to gain access (i.e. halls and landings) or

to protect specific valuable items (i.e. office, lounge). Care

should be taken in siting to avoid direct sunlight, strong

lighting and heat sources (hence the vibration detectors in

the kitchen) as these may cause nuisance tripping. They

are best sited so the intruder cuts across the field of view,

see figure 1 (some products are specifically designed for

long corridors in this instance this rule does not apply),

hence a corner position is usually adopted.

3. PIR, ultrasonic, vibration detectors, etc. all have complex

electronics. These are best given their own zone as in the

event of a fault occurring isolating the fault will be quicker

and nuisance tripping quickly eliminated. Magnetic door

contacts tend to be very reliable if installed well within their

magnetic actuation limit. Hence these can be put in series

together on a loop if appropriate. They are also easier to

test if faulty.

4. Wiring is best concealed where possible to prevent

damage and tampering. Try to avoid running along side

mains cables as interference may occur.

5. The sound/strobe unit should be fitted well above head

height to avoid tampering. The wiring should pass directly

through the wall behind the bell to make it inaccessible.

6. The control panel requires a 240V power source. An

unswitched fused spur preferably direct from the consumer

unit on its own fuse wired in accordance with the current

IEE regulations should be provided.

Using the above general rules you should plan your installation

on your sketched drawing considering the panel siting, how the

cable runs can be minimised, where different types of detector

will be fitted and which zone they will be on. When you have

finalised your plan you can begin installation.

Mounting the control panel and keypad

Control panel

1. Remove the lid screws.

2. Disconnect the a.c. lead from the PCB (see figure 5).

3. Gently pull the PCB from its nylon mounts.

4. Offer the panel up to the wall and mark the holes.

5. Using suitable fixings for the wall material, fix the panel to

the wall.

Securit 7 Alarm Panel

Stock No. 436-881

Garage

Kitchen

Dining

Room

Lounge

Hall

A A

Figure 1. Ground floor view of a domestic premises

Office

Factory

Lobby

Accounts

Figure 2. Ground floor view of a commercial premises

A. Magnetic door contact zone 1

B. Zone 2

C. Zone 3

D. Magnetic door contact zone 4

E. Zone 5

F. Zone 6 may be a PIR on the

first floor landing

G. PIR

H. Siren

I. Personal attack switch

J. Vibration detector

K. Keypad

L. Control panel

Note: Alarm control panel should

be located within the

protected area

A. Magnetic contact zone 1

B. Zone 2

C. Dual tech zone 3

D. Seismic detector zone 4

E. Zone 5

F. Zone 6

G. PIR

H. Siren

I. Personal attack switch

J. Keypad

K. Control panel

L. Additional keypad

Keypad

1. Pushing a terminal screwdriver into the slot on the right-

hand side of the keypad to release the back plate.

2. Mark the wall using the holes at the left and right-hand side

of the back plate. Also mark the large cable entry hole.

3. Fix the back plate to the wall using suitable fixings for the

wall material.

Note: The cable entry hole should also be made if

applicable.

Wiring

Keypad

Install a 6-core cable (RS stock no. 365-587) between the

panel and the keypad. Connect units as shown in figure 3.

Note: If the tamper circuit is used throughout the installation it

is recommended that an additional connector block

(such as RS stock no. 423-655) be used to loop the

tamper circuit between zones (see figure 4 for wiring

details).

Mains

A mains supply should be connected via an unswitched 3A

fused spur wired in accordance with the current IEE

regulations. The mains unit cable should be brought in a

separate entry to the panel to the low voltage cables. If in

doubt consult a qualified electrician.

At this stage it is worth checking the panel for correct operation,

this can be done as follows:

1. Check that the terminals marked Ô24 hour tamper, 1, 2, 3,

4, 5, 6 and PAÕ have loop connections as shown below:

Screw the lid on the control panel.

2. Switch on the mains.

3. Enter Ô1234Õ the buzzer will emit a steady sound and the

exit time start. Press the Ô*Õ key followed by the Ô9Õ key.

The exit buzzer will stop and all LEDs will light. After the

10 seconds LED test the internal sounder, which will

operate for 5 seconds, the control will then emit an accept

tone and revert to the ÔDAYÕ mode. You may end the test

at any time by pressing the Ô*Õ key.

4. The test is now complete.

5. Should the above not occur re-check your wiring and

repeat steps 1. to 4.

BELL

SPK AUX L ID D C

R S 12 3 4 56PA

24 HR

TAMPER

TAMPER 12V

B C

LINK 1

Figure 3. Keypad connections

12 3 4 56PA

24 HR

TAMPER

Figure 4.

TamperPA

* * *

Power

supply

Tamper

detect

N/C N/C

BELL

SPK AUX L ID D C

R S 123456PA

24 HR

TAMPER

I I

Figure 5. Control panel detector connections

A. Securit 7 control panel

B. Tamper switch

C. Bleeper

D. Remote keypad

A. Securit 7 control panel

B. AC lead connection

C. Link 2 memory default

D. Battery fuse 1A

E. Auxiliary 12V supply for PIRs etc.

F. Link 1 (remove this link for panel tamper)

G. Part set volume

H. 6-core cable

I. Additional tamper connectors

J. Passive infrared detector zone 1

K 4-core cable

L. Zone 3

M. Magnetic contacts N/C

N. Personal attack switch

*Additional zone loops show detector normally closed contacts only for clarity

Detectors

The detection circuits consist of 2 series loops, (see figure 6).

The actual detection zone and the 24 hour tamper loop. The

detectors have normally closed contacts that break the series

loop in the event of an alarm or a device being tampered with.

Hence when wiring to a passive infrared (PIR) or vibration

detector or any other electronic detection device 6-core cable

(RS stock no. 365-587) is required to provide zone, 24 hour

and 12V power for magnetic door contacts.

A 4-core cable (RS stock no. 365-571) would be required.

Where a mixture of detectors are used 6-core can be used

throughout and 2-cores ignored for magnetic contacts. Figure

5 illustrates typical connections.

For detectors in the RS product range run the required cable to

each detector and connect up as illustrated.

Testing

Replace the lid on the control panel. Switch the mains on. If

the internal sounder sounds and the ÔTamperÕ LED is lit on the

keypad then there is a break in the tamper series circuit.

Check the covers on all detectors, keypads and control panel to

ensure that the tamper switches are operating. If this does not

cure the fault re-check the tamper wiring connections.

The test procedure is as follows:

1. Type Ô1234Õ into the keypad, the exit time buzzer will begin.

2. Before the exit times out press Ô*Õ followed by Ô9Õ and Ô4Õ.

The buzzer will emit a low level steady tone.

3. Walk around to each detector and check for operation. The

keypad will give a loud pulsing tone to indicate correct

operation and the zone number LED will light whilst the

detector is operated.

4. When the test is over press the Ô*Õ key to finish.

Should any detector not operate at the end of the test re-check

your wiring and re-test.

Sounder/strobe connections

The sounder strobe wiring should now be installed.

Connections for the RS range of units are given in figure 7.

The installation and testing of these units should be as the

included instructions with each sounder/strobe unit.

Internal sounder (speakers)

The control panel is not fitted with a speaker in the box. If

internal speakers are required they should be connected to the

terminals marked SPEAKER (see figure 6). A maximum of two

16½ speakers may be fitted in parallel.

Programming

Programming of the panel can be divided into ÕuserÕ and

ÔengineerÕ programming facilities. The user facilities are those

that may need to be changed in day to day use of the panel

and the engineer facilities are those that will be set up when the

alarm is initially installed. The panel is also set up initially with

factory default settings, these are listed below.

Factory defaults

User/customer code 1 1234

User/customer code 2 Disabled (0000)

Engineer code 7890

Circuit 1 Entry circuit (fixed)

Circuit 2 Alarm circuit isolated in part set

Circuit 3 Alarm circuit

Circuit 4 Alarm circuit

Circuit 5 Alarm circuit

Circuit 6 Alarm circuit

Circuit 7 PA circuit (fixed)

Full set exit time 30 seconds

Part set exit time 15 seconds

Entry time 30 seconds

Bell ring time 15 minutes

Chimes Disabled

User programming

These are functions alterable whilst the panel is unset or by

using the user code.

Changing the user code

There are two separate user codes available. At default the

second user code will be disabled.

1 Master user

2 Second user

Enter the four digit user code, the buzzer will emit a steady

sound and the exit time start. Press the Ô*Õ key followed by the

Ô9Õ key, followed by the key for the user to be altered. The

LEDs 1, 2, 3 and 4 will now come on to indicate a new 4 digit

code is required. Enter your new code. As you press each key

one LED will go out. If your new code is allowed an accept

tone will be given. If the new code is barred an error tone will

be given and your old code will still be valid. Start again and

enter a different four digit code.

24 HR

TAMPER

etc.

N/C

12V

Figure 6. Schematic diagram of detector connections

BELL

SPK AUX L ID D C

R S

stock no.

740-427 Ret sig 0V

740-433 Ret sig 0V

437-660 Return -Ve

Siren

trig.

Strobe

trig.

Siren

trig.

Strobe

trig.

-Ve N/A

+Ve

Figure 7. Sounder/strobe unit connections

A. Magnetic contact

B. PIR

A. Securit 7 control panel

B. AC indicator

C. Battery

D. 2 x 16½ speakers max.

E. RS sounder/strobe

connections

To remove or disable a second user code enter the four digit

user code, the buzzer will emit a steady sound and the exit time

start. Press the Ô*Õ key followed by the Ô9Õ key followed by the Ô2Õ

key. The LEDs 1, 2, 3 and 4 will come on to indicate a new 4

digit code is required. Enter Ô0-0-0-0Õ (four zero keys). As you

press each key one LED will go out. After the last key an accept

tone will be given and the second user code will be disabled.

Chime zones

During the day there may be an area in the building that you

would want to know the presence of a person (e.g. garage)

without setting the alarm. This can be done using the chime

setting. When the detector in the chime zone is activated the

keypad will chime. This can be set as follows:

Whilst the panel is unset press the Ô*Õ key the display will show

the zones currently in chime mode. Press the key number of

the zone you wish to change. If the zone does not have a

chime (e.g. fire or PA zone) an error tone will be given. Press

the Ô*Õ key to finish.

Engineer programming

To enter the engineer programming mode the following

procedure must be followed.

1. The lid should be off the control panel.

2. Switch the mains supply on. The internal sounder will start.

3. Enter Ô1234Õ followed by the Ô#Õ button, this will silence the

sounder, the tamper LED will flash on the remote keypad.

4. Enter Ô7890Õ, the tamper LED will go out and the mains LED

will flash, the panel is now in Ôengineer programming

modeÕ.

The following options are now available for programming to

individual requirements.

Exit time 3-0 range 10-90 seconds

Enter 3-0 LED 3 will light up. This has been preset for factory

default - at 30 seconds. A new time may be programmed by

entering one key from the following table. Once program is set

press Ô*Õ to confirm. The accept tone will sound.

Enter 1 10 seconds

Enter 2 15 seconds

Enter 3 30 seconds

Enter 4 45 seconds

Enter 5 60 seconds

Enter 6 90 seconds

Entry time 3-1 range 10-90 seconds

Enter 3-1 LED 3 will light up. Again this has been preset for

factory default at 30 seconds. To reprogram the entry time

follow exactly the same directions as the EXIT. Again press Ô*Õ

to confirm option. The accept tone will sound.

Enter 1 10 seconds. LED 1 on.

Enter 2 15 seconds. LED 2 on.

Enter 3 30 seconds. LED 3 on.

Enter 4 45 seconds. LED 4 on.

Enter 5 60 seconds. LED 5 on.

Enter 6 90 seconds. LED 6 on.

Bell duration (Bell ring time) 3-2 range 3-20 minutes

Enter 3-2 LED 5 will light up. This has been preset for factory

default at 15 minutes. A new time may be programmed by

entering one key from the following table. Once program is set

press Ô*Õ to confirm. The accept tone will sound.

Enter 1 3 minutes. LED 1 on.

Enter 2 4 minutes. LED 2 on.

Enter 3 5 minutes. LED 3 on.

Enter 4 10 minutes. LED 4 on.

Enter 5 15 minutes. LED 5 on.

Enter 6 20 minutes. LED 6 on.

Part set exit time 3-3 range 0-90 seconds.

Enter 3-3 LED 2 will light up. This has been preset for factory

default at 15 seconds. A new time may be programmed by

entering one key from the following table. Once program is set

press Ô*Õ to confirm. The accept tone will sound.

Enter 0 0 seconds. All LEDs off (instant set in part set).

Enter 1 10 seconds. LED 1 on.

Enter 2 15 seconds. LED 2 on.

Enter 3 30 seconds. LED 3 on.

Enter 4 45 seconds. LED 4 on.

Enter 5 60 seconds. LED 5 on.

Enter 6 90 seconds. LED 6 on.

Note: The exit sounder volume can be altered in part set only

by the control marked PART SET VOLUME. The level

can be reduced to almost zero. When the control sets

an accept tone will sound.

Circuit programming

Circuits 2-6 can be reprogrammed to suit your requirements.

Circuit 1 is fixed as a final exit circuit. Circuit 7 is fixed as a PA

circuit. Circuit 8 is the global tamper circuit. The method of

programming is as follows:

Enter 4-2 for zone 2 Enter 4-3 for zone 3

Enter 4-4 for zone 4 Enter 4-5 for zone 5

Enter 4-6 for zone 6

Select the circuit you wish to alter. That circuit may then be

programmed by entering one key from the following table.

Once program is set press Ô*Õ to confirm, the accept tone will

sound.

Enter 1 Alarm.

Enter 2 Alarm with walkthrough.

Enter 3 Alarm with isolate in part set.

Enter 4 Alarm with walkthrough isolated in part set.

Enter 5 Full set alarm with walkthrough and part set entry.

Enter 6 Fire.

Extended programming options

Once all zones have been programmed you now have further

options available. Again bring up the LED to enable the option

and extinguish the LED to remove the option. ENTER Ô7Õ to

access the extended options then enter a key from the table

below.

Enter 1 - LED 1 Disable external bell and strobe in part set.

Enter 2 - LED 2 Chime enable.

Enter 3 - LED 3 Full set door sense setting.

Enter 4 - LED 4 Convert ID output to signal mains fail.

Enter 5 - LED 5 Allow the isolation of zone 1 (Entry/Exit) in

part set.

Enter 6 - LED 6 Allow PA from remote keypad by pressing Ô*Õ

and Ô#Õ together.

Press * to confirm. The accept tone will sound.

Engineering access code

The engineer access code is programmed to Ô7890Õ as a

factory default. To change this code:

Enter 1-1 LEDs 1, 2, 3 and 4 will light up. Enter the new 4 digit

code. After each keypress one LED will go out. The speaker

will emit an accept tone if the new code is accepted. If the

speaker emits an error tone and all LEDs are extinguished the

old access code is still valid. Repeat the procedure using a

different code.

Engineer event log review

The engineer log is organised into SET and UNSET events.

The log will show the first to alarm and subsequent alarms as

well as isolated circuits. First to alarm is shown by the LED

being ÔonÕ continuously. Subsequent alarms are shown by the

LED(s) flashing and isolated circuits are shown by LED(s)

pulsing slowly. The buzzer will sound whilst reviewing the

ÔSETÕ logs and silent whilst reviewing the ÔUNSETÕ logs.

To view the engineer logs proceed as follows:

From the program mode press the Ô5Õ key. The log routine will

start with DAY 1 SET. The remaining logs are viewed by

pressing the relevant key Ô2Õ for 2nd, Ô3Õ for 3rd etc. on to log 9.

Pressing the Ô0Õ key gives the last alarm condition. The Ô#Õ key

will alternate between ÔSETÕ and ÔUNSETÕ logs and can be used

at any time. To exit logs press the Ô*Õ key.

Factory programming defaults 9-9

Factory defaults have been split into two sections,

programming and codes.

To return to factory programming defaults enter 9-9 the

sounder will give a rapid pipping sound (the entry hurry up

warning). Then enter the engineer code. If entered correctly

an accept tone will sound and the factory programming defaults

will be restored. If any error is made an error tone will sound

and the programming will not be altered. The user and

engineer codes are not changed.

If at any stage you want to return the panel to factory default

user/customer codes, place the small link supplied with the

spare fuses, on the memory link (positioned below the

microprocessor in the centre of the PCB (see figure 4) then

remove the mains and battery supply. When the supply is

restored, the speaker will omit the accept tone and the factory

user code defaults will be restored.

Remove the link.

Once programming is complete exit engineer program mode by

pressing Ô*Õ followed by Ô#Õ, the panel will now be day mode.

Disconnect the mains from the panel. Now connect in the

backup battery (usually 12V 2.8 AH RS stock no. 597-829), the

sounder will indicate a tamper, screw the control panel lid on

and press Ô1234Õ (or your user code if re-programmed) to

silence the alarm. The system is now ready for use.

Note: It is strongly advised that both the user and engineer

code are changed from the factory default.

In the event of the panel not working as described above

please re-check your wiring against the wiring diagrams figures

3, 4 and 5. Remember you can isolate zones by installing wire

links shorting the zone out at the panel.

User instructions

1.0 Setting

1.1 Full set

To start the exit procedure ensure all alarmed doors and

windows are closed and enter the four digit user code, the

buzzer will emit a steady sound and the exit time start.

Leave the building by the approved exit route and close the

final exit door. Wait outside the door until the buzzer has

stopped to indicate that the panel has armed.

If any zones are in fault the buzzer will pulse and the LED

for that zone will be lit. Return to the panel and press the

Ô#Õ key or enter the user code to abort the exit procedure.

Investigate the fault and correct if possible, then start the

exit procedure again. If you do not complete the exit

procedure before the exit time runs out the internal sounder

will start. Enter your user code to stop the sounder. See

section 3.3 to reset the control.

1.2 Part guard

Start the exit procedure as for full set as above. Then press

the Ô*Õ key followed by the Ô0Õ key. The buzzer will change

tone and the LEDs for any zones programmed to be

isolated in part guard will flash. The programmed part

guard exit time will be selected and the exit procedure will

continue. If your system does not allow part guard an error

tone will sound and the exit procedure will be aborted.

1.3 Manual isolation

Start the exit procedure as for full set as above. Then press

the Ô*Õ key followed by the number for each of the zones you

require to isolate. If the zone is isolated the LED for the

required zone will flash and the exit procedure continue.

2.0 Unsetting

Enter by the usual route, the buzzer will sound, do not stop

go directly to the control. Enter the four digit code, the

buzzer will stop and the control return to the ÔDAYÕ mode. If

the exit time has less than 10 seconds remaining the

buzzer will emit a quick pulsing sound to indicate ÔHURRY

UPÕ.

3.0 Tamper faults during day

A tamper fault during the day is indicated by the internal

sounder and the tamper LED. Enter the four digit user code

to stop the sounder, the sounder will now change to a low

level two tone alternating sound to indicate that there is a

ÔRESET REQUIREDÕ. Press the Ô#Õ key to reset the control.

3.1 Alarms during the set period

Enter the four digit user code to unset the system. The

LED display will indicate which zone caused the alarm.

See section 3.3 to reset the control.

3.2 Personal attack alarms

Enter the four digit user code to stop the sounder. Reset

the personal attack button with the key provided. See

section 3.3 to reset the control.

3.3 Resetting the system

To reset the control enter the user code, the sounder will

emit a low level two tone alternating sound to indicate that

there is a ÔRESET REQUIREDÕ. Press the Ô#Õ key to reset

the control. An accept tone will be given, the LEDs for the

zones in alarm will go out and the control will return to the

ÔDAYÕ mode.

4.0 User options

4.1 Auto test

Enter the four digit user code, the buzzer will emit a steady

sound and the exit time start. Press the Ô*Õ key followed by

the Ô9Õ key. The exit buzzer will stop and all LEDs will light.

After the 10 seconds LED test the internal sounder, bell and

strobe will each operate for 5 seconds, the control will then

emit an accept tone and revert to the ÔDAYÕ mode. You

may end the test at any time by pressing the Ô*Õ key.

4.2 Reviewing the alarm logs

The logs are organised as ÔSETÕ and ÔUNSETÕ events. All

events are recorded. The first alarm is shown by the

relevant LED being lit continuously. Subsequent alarms are

shown by a fast pulse of the zone LED. Any zones isolated

are shown by a slow pulse of the zone LED. The buzzer

will sound whilst viewing the ÔSETÕ logs but will be silent

whilst viewing the ÔUNSETÕ logs.

Pressing the Ô#Õ key will change between viewing the ÔSETÕ

and ÔUNSETÕ logs. This may be done at any time. The log

review will automatically end after 15 seconds if no keys are

pressed.

Enter the four digit user code, the buzzer will emit a steady

sound and the exit time start. Press the Ô*Õ key followed by

the Ô9Õ key, then press the Ô3Õ key. The log routine will start

viewing ÔDAYÕ 1 ÔSETÕ.

Key View

1 Log 1

2 Log 2

3 Log 3

4 Log 4

5 Log 5

6 Log 6

7 Log 7

8 Log 8

9 Log 9

0 The last alarm

Press the Ô*Õ key to finish.

4.3 Walk test

You should test your system at regular intervals, to aid this

a walk test mode is provided. You are allowed to test all

ALARM devices. DO NOT TEST ANY PERSONAL

ATTACK BUTTONS.

Enter the four digit user code, the buzzer will emit a steady

sound and the exit time start. Press the Ô*Õ key followed by

the Ô9Õ key, then press the Ô4Õ key. The buzzer will emit a

low level steady tone.

As you test each device the internal sounder will give a loud

pulsing tone to indicate the correct operation of that device.

The zone number LED will light. When the device test is

over the sounder will stop and the zone LED will go out.

The buzzer will emit a low level steady tone as before.

Report any faults to your alarm company.

Press the Ô*Õ key to finish.

Technical specification

Power supply

Mains supply voltage 240V~ Nom

PSU input voltage 13.7V~ Nom

PSU output voltage 12V Nom

Maximum output current 1A (total)

Aux. current 500mA max

Battery fuse 1A (20mm)

Panel quiescent 40mA

Keypads

Supply voltage 12V

Quiescent current 20mA

Active 45mA

Maximum cable run 100 metres

General

Operating temperature 10 to 50¡ centigrade

Humidity Up to 80% non condensing

Dimensions 263mm (W)

223mm (H)

82mm (D)

Control panel weight 2.7kg excluding batt.

Standby battery 2.6AH 12V rechargeable

6AH max.

RS Components Issued November 1994 9954

This manual suits for next models

Table of contents

Other RS Security System manuals

RS 566-780 User manual

RS 408-735 User manual

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual