Rose electronics UltraLink 2 User manual

UltraLink 2

Quick Start Guide

UL2-SA (Single Access)

FRONT

REAR

To KVM

To Computer

UL2-DA (Dual Access)

Switch 1 - Power Option switch

Switch 2 - unit configuration switch

Located on the side of all models

(S1 and S2 Off for normal operation)

To configure the UL 2, the default IP address (192.168.1.42) must be changed to be compatible with

your network. There are two different ways to configure the UltraLink 2’s network information, using the

USB ports or a network crossover cable. Following explains both methods.

1- Unit Configuration via USB ports

The configuration procedure using USB connections is shown below.

1. Position Switch 2 on the UltraLink 2 to the ON position

2. Disconnect unit from the network if connected (computer and monitor should be ON)

3. Connect the PS/2 to USB adapters to the CPU adapter cable and to the computer’s USB ports.

4. Connect the PS/2 connectors on the other end of the cable to the UltraLink 2’s PS/2 connectors.

5. When the keyboard and mouse connectors are connected to the UltraLink 2, the computer

operating system will detect the UltraLink 2 unit as a removable drive.

6. Using Windows explorer, select the UL-2 removable drive and you should see a text file name

“Config.txt”. Edit this text file using a text editor like Notepad and change the IP Address, IP

NetMask and IP Gateway to the IP address information assigned to the UltraLink 2 unit. Also the

Unit name, Use DHCP, and Reset Admin Password options can be selected here. Complete

instructions are included in the “Config.txt” file.

7. When changes are complete, save the file and close the text editor.

PS/2 to USB

adapters

Dual access model

connect to lower

PS/2 ports

DO NOT

Connect the monitor

HD15 connectors

CPU Adapter

Cable

Computer Requirements

OS – XP or Vista

2 – USB 2.0 ports

8. From Windows explorer, right click on the removable drive and “Eject” the disk.

9. Wait 2-5 seconds, and then choose “Safely Remove USB Mass Storage Device” by clicking on the

“Safely Remove Hardware” ICON in the bottom right Windows toolbar.

10. Disconnect the CPU adapter cable from the computer, wait 15 second, position S2 to the “OFF”

position.

The UltraLink 2 is now configured and ready to install to your network.

2- Unit Configuration via Network crossover connection

To modify the IP address, connect the UltraLink 2’s RJ45 port to a computer configured with

an Ethernet card. Use a network cross over cable to connect the computer to UltraLink 2.

Connect the computer to be accessed as shown below using the supplied CPU adapter

cable.

1-On a windows operating system, access the control panel, network tab on the computer

being used to configure the UltraLink 2 and change the existing IP address to

192.168.1.40 and the IP network mask to 255.255.255.0. This change creates a

compatible standalone network between the UltraLink 2 and the computer.

2- From the computer used to configure the unit, start a web browser and enter the IP

address 192.168.1.42 as the URL. The UltraLink 2 will answer with the following display in

the browser.

1-Click on the link

“Connect using built-

in VNC Viewer”.

2-The built-in viewer will

start and display the

connected computer’s

video in the window.

Initial connection screen

When the connected computer’s video display, click on the “Configure” tab in the upper right

corner to display the configuration menu.

From the configuration menu, click on “Network Configuration”, the following menu displays.

Network

cross over cable

Computer needed for power

to the UltraLink 2

Dual access

model, connect

to lower PS/2

ports

Change the IP address, network mask, and other network information that has been

assigned to the UltraLink 2. The VNC port (5900) and HTTP Port (80) should only be

changed if they conflict with existing network settings. If you choose to use DHCP, check

the box adjacent to “Use DHCP”. When complete “Save” the new IP information.

NOTE: When the unit is configured properly and connected to the network, if you have

chosen the option “Use DHCP” the IP address will change to whatever IP address your

DHCP server assigns it. Once the IP address has been changed, UltraLink 2 will lose the

connection to the computer used for configuration. Please see the user’s manual for

additional DHCP information.

When complete, change the IP information on the computer used to connect to the

UltraLink 2 back to the original values.

3- Unit Installation / Cabling

Single Access Model

1- Connect the supplied CPU adapter cable from the keyboard,

monitor, and mouse ports on the UltraLink 2 to the

corresponding ports on the computer to access.

2- Connect a standard network cable from the RJ45 connector

on the UltraLink 2 to your network.

Dual Access Model

1- Connect the supplied CPU adapter cable from the keyboard,

monitor, and mouse ports on the UltraLink 2 (bottom ports) to

the corresponding ports on the computer to access.

2- Connect a local keyboard, monitor, and mouse to the

corresponding ports (top ports) on the UltraLink 2.

3- Connect a standard network cable from the RJ45

connector on the UltraLink 2 to your network.

10707 Stancliff Road Phone: (281) 933-7673

Connecting to a KVM switch

1- Connect the supplied CPU adapter cable from the

keyboard, monitor, and mouse ports on the

UltraLink 2 to the corresponding ports on the

KVM switch to access.

2- Dual model only - Connect a local keyboard,

monitor, and mouse to the corresponding ports on

the UltraLink 2 (top ports).

3- Connect a standard network cable from the RJ45

connector on the UltraLink 2 to your network.

3- Operating Instructions (Single and Dual access models)

With all cabling in place, the default IP address changed to be compatible with your network, and power

applied to the connected computer or switch, access to the connected computer can now be made.

Connecting to the computer can be made from any computer with access to the network UltraLink 2 is

connected to. From a network workstation, start internet explorer or other web browser. Type in the

assigned IP address given to UltraLink 2 in the URL field. The below browser screen will display. Click

on “Connect using built-in Java VNC Viewer”. This will install a temporary small java applet on the

connecting computer and then display the remote computers video.

Click on the “Configure” tab in the upper right corner of the VNC viewer window. This will display

the configuration options. Click on each tab as needed to change/update the information. Below

briefly describes each configuration tab.

User Accounts tab

Allows you to create and manage up to sixteen separate user accounts, each with separate

access permissions. Account #1 is the admin account. Enter User name, password. Tick/un-tick

the Local and Remote options that are appropriate to the user.

Unit Configuration tab

Allows you to alter settings within the UltraLink-2. You can define the keyboard, set-up the admin

account, assign a name to the unit, screensaver time and encryption options

Time and Date Configuration tab

Set the time and date, this time stamps the log files

Network Configuration tab

(Similar to the initial network configuration)

Host Configuration tab

Allows configuration of various details for each host system connected to UltraLink 2. 128 entries

max, Add host names, Users, Hotkey, and Power Control Sequence.

Logging and Status tab

Provides various details about the user activity on the UltraLink 2.

Return to Host tab

Exit the configuration menu system and return to the host computer.

Other manuals for UltraLink 2

Table of contents

Other Rose electronics Switch manuals

Rose electronics

Rose electronics UltraMatrix Remote 2 User manual

Rose electronics

Rose electronics Vista L SERIES User manual

Rose electronics

Rose electronics x series User manual

Rose electronics

Rose electronics UltraView User manual

Rose electronics

Rose electronics Orion XC OXS-XC080-TP User manual

Rose electronics

Rose electronics QuadraVista User manual

Rose electronics

Rose electronics Vista KVL-4PCA Operating and safety instructions

Rose electronics

Rose electronics Vista KVL-4PCA User manual

Rose electronics

Rose electronics UltraMatrix AV DVI User manual

Rose electronics

Rose electronics Vista KM III/A1 User manual

Rose electronics

Rose electronics Xtensys XTS-V16x64D16-L User manual

Rose electronics

Rose electronics RE2-1R2X16U User manual

Rose electronics

Rose electronics VISTA DVI User manual

Rose electronics

Rose electronics UltraLink 2 User manual

Rose electronics

Rose electronics UltraLink UL-V3 User manual

Rose electronics

Rose electronics Ultraview Pro KVM SWITCH WITH ON-SCREEN... User manual

Rose electronics

Rose electronics MultiVideo MEB-4U2V User manual

Rose electronics

Rose electronics Porter PO-4P User manual

Rose electronics

Rose electronics ServeView Pro SEB-8UB User manual

Rose electronics

Rose electronics UltraLink 2 User manual

Rose electronics

Rose electronics MultiVideo HDMI MDM-4T2HD-A1MultiVideo HDMI... User manual

Rose electronics

Rose electronics Vista DVI Plus User manual

Rose electronics

Rose electronics ServeView Pro User manual

Rose electronics

Rose electronics Vista LC DVI User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual