ROSE DISPLAYS ANOKIOSK-STACKABLE User manual

The AnoKiosk™ is a trademark of Rose Displays, Ltd. Neither the

manufacturer nor any sales agent may be held liable for injury, loss or

damage resulting from the use of these products. Part

#02INAnoKioskRigidStackable

Incept-09.20.02

Instruction Sheet

Note:

We recommended that two people

assemble this kiosk.

Step 1a

Slide spine into vertical rail.

Step 1b

Slide another vertical rail onto the

other edge of spine. Repeat for all

vertical rails and spines.

Step 2

Carefully insert corner brackets into

ends of bottom rails, using thumb as

shown in illustration. Two brackets

per end of each rail. Bracket can

bend if forced.

Detail- It is important that the corner

bracket tension tab faces toward

outside of frame. (2b)

Step 3

Lay out parts as they will be configured

on the floor.

Note: One kiosk will have Base Rail

other(s) will have stacker bar.

AnoKiosk™

Instructions for Assembly

Kiosk spine Corner brackets

Parts

Single rails Split rails

(Continued on other side)

2a 2b

1a 1b

35 Congress Street, Salem, MA 01970

Tel# 1- 800 631-9707 Fax# 1-800-560-2890

e-mail:signware@rosedisplays.com

Bottom Rails

with Base Rail

3-Way

4-Way

Bottom Rails

with Stacker Bar

The AnoKiosk™ is a trademark of Rose Displays, Ltd. Neither the

manufacturer nor any sales agent may be held liable for injury, loss or

damage resulting from the use of these products. Part

#02INAnoKioskRigidStackable

Incept-09.20.02

Instruction Sheet (side 2)

Instructions for Assembly continued

AnoKiosk™

35 Congress Street, Salem, MA 01970

Tel# 1- 800 631-9707 Fax# 1-800-560-2890

e-mail:signware@rosedisplays.com

Step 4

Assemble the vertical rail assem-

blies onto the upward facing

corner brackets already inserted

into the bottom rails. All four

brackets should go into the

vertical rails at one time.

Note: (4 way only) The last

vertical rail will be tensioned.

This is normal.

Step 5

Insert corner brackets into ends

of split rails, 1 per end. Use thumb

as shown in illustration.

Step 6

Assemble split rails onto top ends

of vertical rails, one inside and

one outside of each side of the

AnoKiosk.

Step 7

Insert graphics into kiosk

with Base Rails.

Step 8

Place kiosk with stacker bar on

top of first kiosk. Line up stacker

bar with split rails on lower kiosk

and snap together.

Step 9

Load graphics into upper kiosk.

Step 10

If there are more kiosks to be

stacked repeat steps 8 and 9.

Figure 8 Figure 9

The AnoKiosk™ is a trademark of Rose Displays, Ltd. Neither the

manufacturer nor any sales agent may be held liable for injury, loss or

damage resulting from the use of these products. Part

#02INAnoKioskRigidStackable

Incept-09.20.02

Instruction Sheet

Note:

We recommended that two people

assemble this kiosk.

Step 1a

Slide spine into vertical rail.

Step 1b

Slide another vertical rail onto the

other edge of spine. Repeat for all

vertical rails and spines.

Step 2

Carefully insert corner brackets into

ends of bottom rails, using thumb as

shown in illustration. Two brackets

per end of each rail. Bracket can

bend if forced.

Detail- It is important that the corner

bracket tension tab faces toward

outside of frame. (2b)

Step 3

Lay out parts as they will be configured

on the floor.

Note: One kiosk will have Base Rail

other(s) will have stacker bar.

AnoKiosk™

Instructions for Assembly

Kiosk spine Corner brackets

Parts

Single rails Split rails

(Continued on other side)

2a 2b

1a 1b

Bottom Rails

with Base Rail

3-Way

4-Way

Bottom Rails

with Stacker Bar

The AnoKiosk™ is a trademark of Rose Displays, Ltd. Neither the

manufacturer nor any sales agent may be held liable for injury, loss or

damage resulting from the use of these products. Part

#02INAnoKioskRigidStackable

Incept-09.20.02

Instruction Sheet (side 2)

Instructions for Assembly continued

AnoKiosk™

35 Congress Street, Salem, MA 01970

Tel# 1- 800 631-9707 Fax# 1-800-560-2890

e-mail:signware@rosedisplays.com

Step 4

Assemble the vertical rail assem-

blies onto the upward facing

corner brackets already inserted

into the bottom rails. All four

brackets should go into the

vertical rails at one time.

Note: (4 way only) The last

vertical rail will be tensioned.

This is normal.

Step 5

Insert corner brackets into ends

of split rails, 1 per end. Use thumb

as shown in illustration.

Step 6

Assemble split rails onto top ends

of vertical rails, one inside and

one outside of each side of the

AnoKiosk.

Step 7

Insert graphics into kiosk

with Base Rails.

Step 8

Place kiosk with stacker bar on

top of first kiosk. Line up stacker

bar with split rails on lower kiosk

and snap together.

Step 9

Load graphics into upper kiosk.

Step 10

If there are more kiosks to be

stacked repeat steps 8 and 9.

Figure 8 Figure 9

This manual suits for next models

Table of contents

Other ROSE DISPLAYS Accessories manuals

ROSE DISPLAYS

ROSE DISPLAYS ANOGOTCHA FRAME ROUND User manual

ROSE DISPLAYS

ROSE DISPLAYS BUTTERFLY CLIPS WITH CABLE AND SAUCER User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME SQUARE WITH CABLE CLIP AND BALL... User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOGOTCHA SQUARE WITH WALL HANGERS User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOQUICK WITH PEG AND MULTICLIPS User manual

ROSE DISPLAYS

ROSE DISPLAYS PIG TAIL User manual

ROSE DISPLAYS

ROSE DISPLAYS SUPERSNAP WITH CABLE CLIP AND CABLE AND... User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME SQUARE WITH NO LOAD WITH MULTICLIPS User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME ROUND ASSEMBLED-SLATWALL User manual

ROSE DISPLAYS

ROSE DISPLAYS COVER User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME VERSAMOUNT CLAMP BASE User manual

ROSE DISPLAYS

ROSE DISPLAYS RAN-BAS-CC WITH BALL CHAIN User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOMULTI ROUND WITH CABLE CLIP AND LOOP AND... User manual

ROSE DISPLAYS

ROSE DISPLAYS BUTTERFLY CLIPS WITH NON-LOCKING HOOKS User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME SQUARE WITH MULTICLIPS User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME SQUARE WITH CABLE CLIP AND CABLE AND... User manual

ROSE DISPLAYS

ROSE DISPLAYS ECONOFRAME WITH CABLE CLIP AND BALL CHAIN User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOGOTCHA ROUND WITH SLATWALL User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME ROUND NO LOAD WITH WALL HANGERS User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME ROUND ASSEMBLED-TOGGLEBOLTS User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOGOTCHA ROUND WITH WINDOW MOUNTS User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOQUICK SQUARE WITH CABLE CLIP AND BALL... User manual

ROSE DISPLAYS

ROSE DISPLAYS GOTCHA WITH ADHESIVE User manual

ROSE DISPLAYS

ROSE DISPLAYS RAN-BAS-CC WITH LOOP AND BALL User manual

Popular Accessories manuals by other brands

Hillco

Hillco 2810 Operator's manual

Siemens

Siemens QSA2700D Basic documentation

Contours

Contours ZY024 manual

Saivod

Saivod VS621 manual

Virtuox

Virtuox VirtuCLEAN 2.0 user manual

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS user manual

Z-Wave

Z-Wave HSD-200Z user manual

turck

turck FMX-IM-2UPLI63FX quick start guide

Decagon Devices

Decagon Devices 10HS manual

UPPAbaby

UPPAbaby Cup Holder user manual

Elko

Elko SmartSensor Leakage Wireless manual

Grizzly

Grizzly H8371 instructions

Panasonic

Panasonic HG-T Series user manual

IFM Electronic

IFM Electronic Efector 250 Series Brief instructions

DigiDesign

DigiDesign 888/24 I/O installation guide

PROZIS

PROZIS QUAY user manual

patagonia

patagonia PSI Vest user manual

SFC Energy

SFC Energy EFOY GO! manual