ROSE DISPLAYS ANOFRAME VERSAMOUNT SCREW BASE User manual

Parts

35 Congress Street, Salem MA 01970

Tel# 1-800-631-9707 Fax# 1-800-560-2890

e-mail:signware@rosedisplays.com

AnoFrame VersaMountTM Screw Base

Step 1

Locate the two split rails and the solid

rail that is the same length as the split

rails.

Insert two corner brackets into each

end of the solid side Ano rail. Insert

one corner bracket into each end of

each split side Ano rail. Fig. 2

Note: Tension tabs on corner

brackets face towards outside of

frame. Fig. 1

Step 2

For ceiling application, slide screw

tabs into channel of top Ano rail. For

wall applications, slide into side Ano

rail. Fig. 3

Step 3

Place one transitional collar over each

screw tab and push onto frame. Fig. 4.

Step 4

Finish assembling frame following the

sequence in Fig. 5.

Note: Placement of split rails will

depend on type of frame. Split rails

will be on the top for top-loading

frames and on the side for side-

loading frames.

split rails

solid rail

Instructions For Assembly

Incept-9.6.02

Figure 1

The AnoFrame VersaMount is a trademark of Rose Displays, Ltd. Neither

the manufacturer nor any sales agent may be held liable for injury, loss

or damage resulting from the use of these products.

Part #02INSVersaMountScrewBase

Figure 3

Corner

Brackets

AnoFrame

Rails

AnoFrame

Split Rails

Figure 2

Figure 4

Screw Tabs

Transitional

Collars Posts

Screw

Bases

Instruction Sheet (page 1 of 2)

solid rail

split rails

Figure 5

Wood Screws

or Togglebolts

Screws

#97-0451R

Parts

Step 5

Screw posts onto screw tabs and

tighten. Fig. 6

Note: Use the end of the post with

the smaller opening.

Step 6

Insert one screw through the middle

opening on each screw base and into

the posts. Fig. 7

Tighten with screwdriver. Fig 8

Step 7

Install screw bases using wood screws

and screwdriver. Fig. 9

Note: Togglebolts are recommended

for drywall installations (predrilling

3/8” holes is necessary)

Step 8

Slide your graphic into the AnoFrame.

Fig. 10

Instructions For Assembly

Incept-9.6.02

Figure 6

The AnoFrame VersaMount is a trademark of Rose Displays, Ltd. Neither

the manufacturer nor any sales agent may be held liable for injury, loss

or damage resulting from the use of these products.

Part #02INSVersaMountScrewBase

Figure 7

Finished Look

35 Congress Street, Salem, MA 01970

Tel# 1- 800 631-9707 Fax# 1-800-560-2890

e-mail:signware@rosedisplays.com

Instruction Sheet (page 2 of 2)

AnoFrame VersaMountTM Screw Base

Figure 8 Figure 9

#97-0451R

Figure

Parts

AnoFrame VersaMountTM Screw Base

Step 1

Locate the two split rails and the solid

rail that is the same length as the split

rails.

Insert two corner brackets into each

end of the solid side Ano rail. Insert

one corner bracket into each end of

each split side Ano rail. Fig. 2

Note: Tension tabs on corner

brackets face towards outside of

frame. Fig. 1

Step 2

For ceiling application, slide screw

tabs into channel of top Ano rail. For

wall applications, slide into side Ano

rail. Fig. 3

Step 3

Place one transitional collar over each

screw tab and push onto frame. Fig. 4.

Step 4

Finish assembling frame following the

sequence in Fig. 5.

Note: Placement of split rails will

depend on type of frame. Split rails

will be on the top for top-loading

frames and on the side for side-

loading frames.

split rails

solid rail

Instructions For Assembly

Incept-9.6.02

Figure 1

The AnoFrame VersaMount is a trademark of Rose Displays, Ltd. Neither

the manufacturer nor any sales agent may be held liable for injury, loss

or damage resulting from the use of these products.

Part #02INSVersaMountScrewBase

Figure 3

Corner

Brackets

AnoFrame

Rails

AnoFrame

Split Rails

Figure 2

Figure 4

Screw Tabs

Transitional

Collars Posts

Screw

Bases

Instruction Sheet (page 1 of 2)

solid rail

split rails

Figure 5

Wood Screws

or Togglebolts

Screws

#97-0451R

Parts

Step 5

Screw posts onto screw tabs and

tighten. Fig. 6

Note: Use the end of the post with

the smaller opening.

Step 6

Insert one screw through the middle

opening on each screw base and into

the posts. Fig. 7

Tighten with screwdriver. Fig 8

Step 7

Install screw bases using wood screws

and screwdriver. Fig. 9

Note: Togglebolts are recommended

for drywall installations (predrilling

3/8” holes is necessary)

Step 8

Slide your graphic into the AnoFrame.

Fig. 10

Instructions For Assembly

Incept-9.6.02

Figure 6

The AnoFrame VersaMount is a trademark of Rose Displays, Ltd. Neither

the manufacturer nor any sales agent may be held liable for injury, loss

or damage resulting from the use of these products.

Part #02INSVersaMountScrewBase

Figure 7

Finished Look

Instruction Sheet (page 2 of 2)

AnoFrame VersaMountTM Screw Base

Figure 8 Figure 9

#97-0451R

Figure

This manual suits for next models

Table of contents

Other ROSE DISPLAYS Accessories manuals

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME VERSAMOUNT CLAMP BASE User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOKIOSK-STACKABLE User manual

ROSE DISPLAYS

ROSE DISPLAYS RAN-BAS-CC WITH LOOP AND SAUCER AND... User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOCONNECTOR WITH ANOQUICK User manual

ROSE DISPLAYS

ROSE DISPLAYS ECONOSTAND WITH ANOQUICK User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME ROUND NO LOAD WITH MULTICLIPS User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOSCREEN WITH ANOFOOT User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOQUICK ROUND WITH MULTICLIPS User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOGOTCHA ROUND WITH CABLE CLIP AND CABLE AND... User manual

ROSE DISPLAYS

ROSE DISPLAYS QUICKGRIP WITH MULTICLIPS User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOQUICK WITH PEG User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOGOTCHA ROUND WITH CABLE AND SAUCER User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOQUICK ROUND WITH CABLE CLIP AND CABLE AND... User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOMULTI ROUND WITH CABLE AND SAUCER User manual

ROSE DISPLAYS

ROSE DISPLAYS CABLE CLIP User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOGOTCHA PLUS WITH MULTICLIPS User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOGOTCHA ROUND WITH CABLE AND BALL User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME VERSAMOUNT MAGNET BASE User manual

ROSE DISPLAYS

ROSE DISPLAYS GOTCHA WITH FISH CLIP User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOQUICK ROUND WITH CABLE AND CRIMP SLEEVES User manual

ROSE DISPLAYS

ROSE DISPLAYS RAN-BAS-CC WITH CORD AND BARB User manual

ROSE DISPLAYS

ROSE DISPLAYS TOPPER CLIPS User manual

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME VERSAMOUNT CEILING ANCHORS User manual

ROSE DISPLAYS

ROSE DISPLAYS QUICKGRIP WITH WINDOW MOUNTS User manual

Popular Accessories manuals by other brands

Hillco

Hillco 2810 Operator's manual

Siemens

Siemens QSA2700D Basic documentation

Contours

Contours ZY024 manual

Saivod

Saivod VS621 manual

Virtuox

Virtuox VirtuCLEAN 2.0 user manual

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS user manual

Z-Wave

Z-Wave HSD-200Z user manual

turck

turck FMX-IM-2UPLI63FX quick start guide

Decagon Devices

Decagon Devices 10HS manual

UPPAbaby

UPPAbaby Cup Holder user manual

Elko

Elko SmartSensor Leakage Wireless manual

Grizzly

Grizzly H8371 instructions

Panasonic

Panasonic HG-T Series user manual

IFM Electronic

IFM Electronic Efector 250 Series Brief instructions

DigiDesign

DigiDesign 888/24 I/O installation guide

PROZIS

PROZIS QUAY user manual

patagonia

patagonia PSI Vest user manual

SFC Energy

SFC Energy EFOY GO! manual