Roger Technology H70/104AC User manual

Quick Start H70/104-105AC

Rev01 17/08/2020

ROGER TECHNOLOGY

Via S. Botticelli 8 • 31021 Bonisiolo di Mogliano Veneto (TV) • ITALIA

P.IVA 01612340263 • Tel. +39 041.5937023 • Fax. +39 041.5937024

info@rogertechnology.com • www.rogertechnology.com

APower supply H07RN-F 3x1,5 mm2double insulated cable

1Photocell - Receiver 4x0,5 mm2double insulated cable (max.20 m)

2Photocell - Transmitter 2x0,5 mm2double insulated cable (max.20 m)

3Flashing lamp unit 2x1 mm2double insulated cable (max.10 m)

4Antenna RG58 50 Ohm cable for external use (max.10 m)

5Selector / Keypad Cavo 3x0,5 mm2 cable (max.20 m)

1. Typical installation

H70/104-105AC is the range of 230V AC digital controllers installed with the M30, H30, R30, G30 and E30 product series for

sliding gate applications.

2. Electrical connections

3. Display: functions and settings

PROG TEST

Back

Programming Check error alarms

PARAMETER PARAMETER

VALUE

Increase value

Decrease value

PROG TEST

Accessories illustrated are indicative only

412 3789 106

27 28

12 13 14 15 16 17 18 19

PROG TEST

COM

COR

LAM

COM

CS1

CS2

FT1

FT2

24V

COM

CORLNPE LAM

24V~

COM

FT2

FT1

COS2

COS1

ORO

PED

COM

ANT

FUSE

F6,3A

FUSE

F315mA

H93/RX22A/I

RICEVITORE RADIO

RADIO RECEIVER

230Vac

PR1

PR2

MOTORE

MOTOR

verde / green

rosso/ red

blu / blue

ENCFC

Orologio / Timer

Apertura parziale

Paral opening

Passo passo / Step by step

Chiusura / Closing

Apertura / Opening

Spia cancello aperto /

Open gate light 24 Vac 2 W

STOP

Bordo sensibile 1

Safety edge 1

Bordo sensibile 2

Safety edge 2

Antenna

RG58 max 10 m

CONDENSATORE

CAPACITOR

H70/104AC

M30

H30

R30

G30

E30

230Vac

ANT

FUSIBILE F200mA

FUSE F200mA

Marrone/Brown

Blu/Blue

RG58 max 10 m

910

12 13 14 15 16 17 18 19

LAM

24V~

COM

FT2

FT1

COS2

COS1

ANT

FIFTHY/230

12 3

LNPE

230Vac

RXTX

12 12345

11 12 13 14 15 16 17 18 19

24V~

COM

FT2

FT1

COS2

COS1

ANT

CS1

CS2

FT1

FT2

24V

COM

24V

FT1

CONNECTION WITH 1 PAIR OF PHOTOCELLS

RECOMMENDED USE for Series

F2ES - F2S photocells

CONNECTION WITH FLASHING LIGHT

4. Before starting ...

e) Select the appropriate self-acquisition procedure for your installation:

A) SELF-ACQUISITION PROCEDURE WITH ENCODER ENABLED, WITH OR WITHOUT LIMIT SWITCHES

B) SELF-ACQUISITION PROCEDURE WITH LIMIT SWITCHES, WITHOUT ENCODER

C) SELF-ACQUISITION PROCEDURE WITHOUT LIMIT SWITCHES AND WITHOUT ENCODER

d) Press the TEST button Possible alarms and safety device messages:

SEE ACQUISITION PROCEDURE

00 No safety device in alarm state and no limit switch activated.

Sb (Sb) Release handle or lock open.

18 STOP contact (N.C.) open.

Jumper the STOP contact.

17 Sensing edge contact COS1 (N.C.) is open. Check connection. If sensing

edge is not installed, disable with 73 00.

16 Sensing edge contact COS2 (N.C.) is open. Check connection. If sensing

edge is not installed, disable with 74 00.

15 Photocell contact FT1 (N.C.) is open. Check connection. If photocell is not

installed, disable with 50 00.

14 Photocell contact FT2 (N.C.) is open. Check connection. If photocell is not

installed, disable with 53 00.

fe Both limit switches in error state. Check connections and settings of limit

switches.

fa If gate is open, gate open limit switch is detected.

fC If gate is closed, gate closed limit switch is detected.

a) Select the position of the motor relative to the gate with the parameter

71 . The default setting for this parameter is with the motor installed

on the right hand side of the gate (seen from interior side).

b) Adjust the (mechanical or magnetic) limit

switches so that, once triggered, the gate stops

slightly before it reaches the mechanical stop.

To verify the correct direction of position with

respect to the passage press TEST.

If the gate is in closed position, FC will be

displayed; if the gate is in open position, FA will

be displayed.

GATE OPENS TO LEFT GATE OPENS TO RIGHT

CLOSING LIMIT SWITCH OPENING LIMIT SWITCH

WARNING: PARAMETER 30 MUST BE THE SAME AS 01

PROG TEST

PROG

TEST

PROG TEST

5. Acquisition procedure (with encoder enabled, with or without limit switches - 75 01)

5. Acquisition procedure (with limit switches, without encoder)

5. Acquisition procedure (without limit switches and without encoder)

1. Press and hold PROG for 4 seconds.

2. APP- appears on the display.

3. Press PROG.

4. AUTO appears on the display.

5. The gate starts to open.

6. When the gate is open after a few seconds AUTO ﬂashes for 2 seconds.

7. When the message AUTO stops ﬂashing sul display the gate starts closing.

8. When the gate is closed, the safety device symbols are displayed.

1. Press and hold PROG for 4 seconds.

2. APP- appears on the display.

3. Press PROG.

4. The gate starts to open.

5. AP1 appears on the display.

6. Once the relative limit switch is activated, the gate stops brieﬂy.

7. PA ﬂashes on the display for 2 seconds.

8. After this 2 second interval, gate closes automatically. The message CH1 appears on the display.

9. When the gate is closed, the safety device symbols are displayed.

1. Press and hold PROG for 4 seconds.

2. APP- appears on the display.

3. Press PROG.

4. The gate starts to open.

5. AP1 appears on the display.

6. When the gate reaches the open position mechanical stop, wait 3-4 seconds then press PROG.

7. PA ﬂashes on the display for 2 seconds.

8. After this 2 second interval, gate closes automatically. The message CH1 appears on the display.

9. When gate reaches the closing mechanical stop, wait 3-4 seconds then press PROG.

10. When the gate is closed, the safety device symbols are displayed.

PROG

AP P- AU to

x4 s

PROG

1 click OPENING OPEN

CLOSING CLOSE

Yes

PARTIALLY

OPEN

AU to

PROG

AP P-

x4 s

x2 s

PROG

1 click

Yes

CH 1

AP 1

OPENING OPEN

CLOSING CLOSE

PARTIALLY

OPEN

PROG

AP P-

x4 s

x2 s

PROG

1 click

PROG

1 click

Yes

CH 1

AP 1

3-4 s

PROG

1 click

3-4 s

OPENING OPEN

CLOSING CLOSE

PARTIALLY

OPEN

6. Setting basic parameters

 Set deceleration space (%)  Set deceleration space (%)

 Set deceleration during closure  Set deceleration during opening

 Set initial acceleration during opening  Set initial acceleration during closing

 Set braking time

 Set braking force

 Adjustment of the motor torque during the total opening and closing manoeuvre

 Set motor torque during deceleration

 Set motor torque boost at starts of manoeuvre

 Set obstacle detection sensitivity during deceleration

 Set obstacle detection sensitivity during manoeuvres

 Setting reverse time after activation of sensing

edge or obstacle detection

(crush prevention)

IN THE CASE OF COUNTRIES WITH VERY COLD TEMPERATURES WE RECOMMEND THAT YOU VIEW

PARAMETERS 36 AND 37 AND THE ACTIVATION OF THE MAXIMUM STARTING POINT.

7. Programming a NEW transmitter

8. Copying a transmitter

1. Press channel P1 (P2) of the receiver.

2. When LED L1 (L2) ashes 3 times (or 4 times

with rolling code function), press any button

on the transmitter.

3. If LED L1 (L2) remains steadily lit the

transmitter has been stored correctly

1. Press buttons A and B on the NEW

transmitter simultaneously.

2. The LED ashes for 5 s.

3. Hold button (A) only on the NEW transmitter

you want to store.

4. The LED ashes 3 s.

5. Hold the previously stored transmitter as

close as possible to the NEW transmitter.

6. Press button (A) on the OLD transmitter.

7. The LED lights for 1 s to conrm that the copy

procedure was successful.

L1 L2

P2 P1

L1 L2

1 click

x5 s x3 s x1 s

AAA

OLD

This document is a basic quick guide for the initial installation of a sliding gate motor.

For complete information concerning the control unit, the motor and the accessories mentioned in this quick guide, see the technical manuals available in the B2B area of the

website www.rogertechnology.it

Other manuals for H70/104AC

This manual suits for next models

Table of contents

Other Roger Technology Gate Opener manuals

Roger Technology

Roger Technology RL651 User manual

Roger Technology

Roger Technology BG30 Series Operating instructions

Roger Technology

Roger Technology B70/1DC User manual

Roger Technology

Roger Technology MONOS4/220 Operating instructions

Roger Technology

Roger Technology BH30 Series Operating instructions

Roger Technology

Roger Technology B70/2ML User manual

Roger Technology

Roger Technology G30/1804 Operating instructions

Roger Technology

Roger Technology BH23 Series Operating instructions

Roger Technology

Roger Technology R20 Series User manual

Roger Technology

Roger Technology H70/200AC User manual

Roger Technology

Roger Technology BRUSHLESS B70/2DC User manual

Roger Technology

Roger Technology B70/2ML User manual

Roger Technology

Roger Technology G30 Series Operating instructions

Roger Technology

Roger Technology R30/803 User guide

Roger Technology

Roger Technology AG/BAJ/02 Operating instructions

Roger Technology

Roger Technology BH23 Series User manual

Roger Technology

Roger Technology BRUSHLESS B70/2DC User manual

Roger Technology

Roger Technology H21 Series User manual

Roger Technology

Roger Technology SND/BA/68/DW User manual

Roger Technology

Roger Technology SMARTY Series Operating instructions

Roger Technology

Roger Technology BE20 Series Operating instructions

Roger Technology

Roger Technology H70/200AC Product manual

Roger Technology

Roger Technology BH30 Series User manual

Roger Technology

Roger Technology R20 Series Operating instructions

Popular Gate Opener manuals by other brands

Elite

Elite CSW200UL instruction manual

CAME

CAME FROG-PM4 installation manual

SOMFY

SOMFY FX230 installation manual

Aprimatic

Aprimatic ONDA 500 installation instructions

Turnstiles

Turnstiles FSW 900 manual

Erreka

Erreka BUL BL33 Quick installation and programming guide

Erreka

Erreka VULCAN S manual

Beninca

Beninca R1-2 WBV quick start guide

Erreka

Erreka VULCAN D user manual

Motorline professional

Motorline professional FORT User& installer's manual

Beninca

Beninca BOB5024 manual

AGA

AGA GATEMASTER 900 HD installation manual

Chamberlain

Chamberlain MotorLift HC280ML Mechanical installation

SOMFY

SOMFY Dexxo RTS Pro INSTALLATION INSTRUCTIONS-ILLUSTRATIONS

Cardin

Cardin BL Series manual

Westfalia

Westfalia 85 27 06 instruction manual

CAME

CAME F500 installation manual

Extel

Extel VERA quick guide