Roger Technology EDGE1 User manual
Quick Start EDGE1
Rev03 18/08/2020
ROGER TECHNOLOGY
Via S. Botticelli 8 • 31021 Bonisiolo di Mogliano Veneto (TV) • ITALIA
P.IVA 01612340263 • Tel. +39 041.5937023 • Fax. +39 041.5937024
info@rogertechnology.com • www.rogertechnology.com
AEDGE1 - Motors connection 3x2,5 mm2double insulated cable (max 10 m) - 3x4 mm2 (max 30 m)
1Photocell - Receiver 5x0,5 mm2double insulated cable (max 20 m)
2Photocell - Transmitter 3x0,5 mm2double insulated cable (max 20 m)
3Flashing lamp unit 2x1 mm2double insulated cable (max 10 m)
4Antenna RG58 or KX6 50 Ohm cable for external use (max 10 m)
5Selector / Keypad 3x0,5 mm2cable (max 20 m)
1. Typical installation
EDGE1 is the range of 36V DC digital controllers installed with the swing gates applications.
EN
2
2
3
4
1
A
A
5
1
PRIMARY
SECONDARY
PROG TEST
+
-
F3 F2
F1
M1 M2
X
-+
X
YY
ZZ
COR
13 14
ANT
F4
15 16 17 18 19 20 21 22 23 24 25 26 27 31 32 33 34 35 36 3729 30
COM
+LAM
+ES
+24V
COM
SC
COM
FT2
FT1
COS2
COS1
COM
ST
COM
ORO
AP
CH
PED
COM
COM
COM
COM
COM
COM
COM
LAM
PED
PP
CH
AP
IN1
ST
CS1
IN2
FT1
FT2
SC
24V
ES
PP
28
AUX
L
N
0190 26
SEC2
SEC1
1
2
3
4
BATTERY CHARGER
BATTERY
TRANSFORMER
Blu/Blue
Blu/Blue
L
N
Nero/Black
Nero/Black
Nero/Black
Nero/Black
Blu/Blue
Blu/Blue
-+
MOTOR
1M
OTOR 2
FIFTHY/24
+-
F4ES-F4S
Series
1 2 3 2345
+- +-
TX RX
1
CS/STD
12
POWER SUPPLY
230 Vac / 115 Vac
BATTERIES
2 x 12V 4,5Ah
2. Electrical connections
3. Display: functions and settings
Accessories illustrated are indicative only
PROG TEST
+
-
Back
Programming Check error alarms
PARAMETER PARAMETER
VALUE
Increase value
Decrease value
Next
PROG TEST
+
-
00 No safety device in alarm state and no limit switch activated.
27 STOP contact (N.C.) open.
Jumper the STOP contact.
25 Sensing edge contact COS1 (N.C.) is open. Check connection. If sensing edge
is not installed, disable with 73 00.
24 Sensing edge contact COS2 (N.C.) is open. Check connection. If sensing edge
is not installed, disable with 74 00.
23 Photocell contact FT1 (N.C.) is open. Check connection. If photocell is not
installed, disable with 50 00.
22 Photocell contact FT2 (N.C.) is open. Check connection. If photocell is not
installed, disable with 53 00.
dATA
Incorrect travel length values / Parameter 71 modied: enabling absolute
encoder (only SMARTY Series).
• Disconnect from mains power or remove the main fuse (F3) and wait 5 seconds.
• Reconnect to mains power or ret the fuse.
• Press and hold PROG until the message ATA and A appear on the display.
Repeat acquisition procedure.
4. Before starting ...
d) Move the gate into the completely CLOSE position.
e) Press TEST button
Possible alarms and safety device messages:
SEE ACQUISITION PROCEDURE
PROG TEST
+
-
PROG
TEST
+
-
PROG TEST
+
-
a) Select the automation system model installed with the parameter A1.
b) Select the number of motors installed with the parameter 70.
This parameter is set for two motors by default.
c) Position the mechanical stops in both the open and closed positions by tightening them very tightly.
* the parameter 71 01 must be set and SMARTY/EMA installed for all applications with the SMARTY REVERSIBLE motor.
1 MOTOR 2 MOTORS
BE20/200/HS SMARTY 5R5 *
BR20 Series SMARTY 4HS
BH23/282 BH23/252/HS
BR21 Series BR21/351/HS
SMARTY 5 BE20/400
SMARTY 7 MONOS4
SMARTY 7R * BR20/400/R
Motor torque
Obstacle impact force
sensitivity MOTOR 1
Motor torque MOTOR2
Obstacle impact force
sensitivity MOTOR 2
Start acceleration MOTOR 1
during opening
Start acceleration MOTOR 1
during closing
Start acceleration MOTOR 2
during closing
Deceleration MOTOR 1 during CLOSING
Deceleration MOTOR 1 during OPENING
Deceleration MOTOR 2 during CLOSING
Deceleration MOTOR 2 during OPENING
Alignment MOTOR1
Stop advance of LEAF 1
when opening
Opening approach distance setting MOTOR1
Closing approach distance setting MOTOR1
Opening approach distance setting MOTOR2
Closing approach distance setting MOTOR2
Stop advance of LEAF 2 when opening
Position control
Position control
Position control
Position control
Alignment MOTOR2
Deceleration MOTOR 1
during CLOSING
Deceleration MOTOR 2
during CLOSING
Opening speed
Opening speed
Closing speed
Closing speed
Start acceleration
MOTOR 2 during opening
MOTOR 1
MOTOR 2
6. Setting basic parameters
5. Acquisition procedure
1. Press and hold PROG for 4 seconds.
2. APP- appears on the display.
3. Press PROG.
4. AUTO appears on the display.
5. MOTOR 1 starts opening at low speed.
6. After the delay time set with parameter 25, MOTOR 2 starts an opening manoeuvre.
7. Once the gate is open, the message AUTO flashes on the display.
8. The message AUTO stops flashing.
9. MOTOR 2 starts closing.
10. After a delay set with parameter 26, MOTOR 1 closes.
11. When the gate is closed, the safety device symbols are displayed.
Press
PROG
AP P- AU to
x4 s
Press
PROG
1 click OPEN
MOTOR 1
OPENING
MOTOR 2
OPENING
PARAM. 25
ùDELAY
TIME
AU to
x2 s CLOSED
AU
AU
to
to
Yes
MOTOR 1
CLOSING
MOTOR 2
CLOSING
PARAM. 26
DELAY
TIME
CLOSED
7. Programming a NEW transmitter
8. Copying a transmitter
P1
L1 L2
P2 P1
L1 L2
P2
ON
P1
L1 L2
P2
1 click
This document is a basic quick guide for the initial installation of a BRUSHLESS swing gate motor.
For complete information concerning the control unit, the motor and the accessories mentioned in this quick guide, see the technical manuals available in the B2B area of the
website www.rogertechnology.it
x5 s x3 s x1 s
AAA
A
B
OLD
1. Press channel P1 (P2) of the receiver.
2. When LED L1 (L2) ashes 3 times (or 4 times
with rolling code function), press any button
on the transmitter.
3. If LED L1 (L2) remains steadily lit the
transmitter has been stored correctly.
1. Press buttons A and B on the NEW
transmitter simultaneously.
2. The LED ashes for 5 s.
3. Hold button (A) only on the NEW transmitter
you want to store.
4. The LED ashes 3 s.
5. Hold the previously stored transmitter as
close as possible to the NEW transmitter.
6. Press button (A) on the OLD transmitter.
7. The LED lights for 1 s to conrm that the copy
procedure was successful.
9. Photocells grounding connection
Grounding connection negative terminal (COM) photocells series F4ES/F4S or other than Roger Technology
In case of malfunction, or failure to intervene in case of dimming, or continuous detection, or abnormal behaviour of the automation (gate, overhead door,
barrier, etc.), it is advisable to connect the negative terminal (COM) of the photocells to the grounding of the system.
M1 M2
XX
YY
ZZ
COR
13 14
ANT
15 16 17 18 19 21 22 23 24 25 26 27 31 32 33 34 35 36 3729 30
COM
+LAM
+ES
+24V
SC
COM
FT2
FT1
INP2
COS1
COM
ST
COM
INP1
AP
CH
PED
COM
PP
RXTX
12 3 12
RXTX
FT1
FT2
MASTER
SLAVE 1
345
123 12345
COM(-)
COM(-)
COM(-)
COM(-)
COM(-)
COM(-)
Table of contents
Other Roger Technology Gate Opener manuals
Roger Technology
Roger Technology H70/200AC Product manual
Roger Technology
Roger Technology G30 Series Operating instructions
Roger Technology
Roger Technology BG30 Series Operating instructions
Roger Technology
Roger Technology AG-K/KB Product manual
Roger Technology
Roger Technology R20 Series User manual
Roger Technology
Roger Technology SMARTY Series Operating instructions
Roger Technology
Roger Technology B70/2ML User manual
Roger Technology
Roger Technology B70/1DC User manual
Roger Technology
Roger Technology H70/200AC User manual
Roger Technology
Roger Technology BR21 Series Operating instructions
Roger Technology
Roger Technology BH23 Series User manual
Roger Technology
Roger Technology B70/2ML User manual
Roger Technology
Roger Technology BH23 Series Operating instructions
Roger Technology
Roger Technology H21 Series Operating instructions
Roger Technology
Roger Technology AG/BAJ/02 Operating instructions
Roger Technology
Roger Technology R20 Series Operating instructions
Roger Technology
Roger Technology BE20 Series Operating instructions
Roger Technology
Roger Technology MONOS4/220 Operating instructions
Roger Technology
Roger Technology M30 Series Operating instructions
Roger Technology
Roger Technology G30/1804 Operating instructions
