Roger Technology BRUSHLESS B70/2DC User manual

Quick Start B70/2DC

Rev01 20/08/2020

ROGER TECHNOLOGY

Via S. Botticelli 8 • 31021 Bonisiolo di Mogliano Veneto (TV) • ITALIA

P.IVA 01612340263 • Tel. +39 041.5937023 • Fax. +39 041.5937024

info@rogertechnology.com • www.rogertechnology.com

APower supply B70/2DC - Motors 3x2,5 mm2double insulated cable (max.10 m) - 3x4 mm2 (max. 30 m)

1Photocell - Receiver 5x0,5 mm2double insulated cable (max.20 m)

2Photocell - Transmitter 3x0,5 mm2double insulated cable (max.20 m)

3Flashing lamp unit 2x1 mm2double insulated cable (max.10 m)

4Antenna RG58 50 Ohm cable for external use (max.10 m)

5Selector / Keypad 3x0,5 mm2cable (max.20 m)

1. Typical installation

B70/2DC is the range of 24V DC digital controllers installed in the swing gates product.

All manuals and user guides at all-guidesbox.com

all-guidesbox.com

2. Electrical connections

3. Display: functions and settings

TRASFORMATORE

Cod. 702_10/0

PRIMARIO

MONOFASE

POT. 150 VA 50/60 Hz

SECONDARIO

CEI 61558-2-6

PROG TEST

POWER IN

M1 M2

COR

910

ANT

11 12 13 14 15 16 17 18 19 20 21 22 23 26 27 28 29 30 31 3224 25

COM

+LAM

+ES

+24V

COM

FT2

FT1

COS2

COS1

COM

ORO

PED

COM

230 Vac

115 Vac

B70/2DC115/BOX

MOTORE 1

MOTOR 1 MOTORE 2

MOTOR 2

FIFTHY/24

CS/STD

Serie

F4ES-F4S

1 2 3 2345

+- +-

TX RX

Accessories illustrated are indicative only

PROG TEST

Back

Programming Check error alarms

PARAMETER PARAMETER

VALUE

Increase value

Decrease value

PROG TEST

All manuals and user guides at all-guidesbox.com

4. Before starting ...

d) Move the gate into the completely CLOSE position.

e) Press the TEST button.

Possible alarms and safety device messages:

SEE ACQUISITION PROCEDURE

00 No safety device in alarm state and no limit switch activated.

23 STOP contact (N.C.) open.

Jumper the STOP contact.

21 Sensing edge contact COS1 (N.C.) is open. Check connection. If sensing edge

is not installed, disable with 73 00.

20 Sensing edge contact COS2 (N.C.) is open. Check connection. If sensing edge

is not installed, disable with 74 00.

19 Photocell contact FT1 (N.C.) is open. Check connection. If photocell is not

installed, disable with 50 00.

18 Photocell contact FT2 (N.C.) is open. Check connection. If photocell is not

installed, disable with 53 00.

27 Limit switch in open MOTOR 1

(BH23 Series, if enabled - 72 01).

20 Limit switch in open MOTOR 2

(BH23 Series, if enabled - 72 01).

PROG TEST

PROG

TEST

PROG TEST

a) Select the automation system model installed with the parameter A1.

b) Select the number of motors installed with the parameter 70. This

parameter is set for two motors by default.

c) Position the mechanical stops in both the open and closed positions by tightening them very tightly.

1 MOTOR 2 MOTORS

BM20 Series BR21 Series

BR20 Series BE20 Series

BH23 Series MONOS4

All manuals and user guides at all-guidesbox.com

6. Setting basic parameters

30 Motor torque

31 Obstacle impact force sensitivity MOTOR 1

33 Motor torque MOTOR 2

32 Obstacle impact force

sensitivity MOTOR 2

34 Start acceleration MOTOR 1

35 Start acceleration MOTOR 2

11 Deceleration

MOTOR 1

12 Deceleration MOTOR 2

26 Closing delay of MOTOR 1

19 Stop advance of

LEAF 1 when opening

20 Stop advance of

LEAF 2 when opening

14 Position control

13 Position control

LEAF 1 position control when

completely opens or closes

14 LEAF 2 position control when

completely opens or closes

25 Opening delay of MOTOR 2

11 Deceleration MOTOR 1

12 Deceleration

MOTOR 2

40 Speed 40 Speed

35 Start acceleration MOTOR 2

MOTOR 1

MOTOR 2

5. Acquisition procedure

1. Press and hold PROG for 4 seconds.

2. APP- appears on the display.

3. Press PROG.

4. AUTO appears on the display.

5. MOTOR 1 starts opening at low speed.

6. After the delay time set with parameter 25, MOTOR 2 starts an opening manoeuvre.

7. Once the gate is open, the message AUTO ﬂashes on the display.

8. The message AUTO stops ﬂashing.

9. MOTOR 2 starts closing.

10. After a delay set with parameter 26, MOTOR 1 closes.

11. When the gate is closed, the safety device symbols are displayed.

Press

PROG

AP P- AU to

x4 s

Press

PROG

1 click OPEN

MOTOR 1

OPENING

MOTOR 2

OPENING

PARAM. 25

ùDELAY

TIME

AU to

x2 s CLOSED

Yes

MOTOR 1

CLOSING

MOTOR 2

CLOSING

PARAM. 26

DELAY

TIME

CLOSED

All manuals and user guides at all-guidesbox.com

7. Programming a NEW transmitter

8. Copying a transmitter

L1 L2

P2 P1

L1 L2

1 click

This document is a basic quick guide for the initial installation of a BRUSHLESS swing gate motor.

For complete information concerning the control unit, the motor and the accessories mentioned in this quick guide, see the technical manuals available in the B2B area of the

website www.rogertechnology.it

x5 s x3 s x1 s

AAA

OLD

1. Press channel P1 (P2) of the receiver.

2. When LED L1 (L2) ashes 3 times (or 4 times

with rolling code function), press any button

on the transmitter.

3. If LED L1 (L2) remains steadily lit the

transmitter has been stored correctly.

1. Press buttons A and B on the NEW

transmitter simultaneously.

2. The LED ashes for 5 s.

3. Hold button (A) only on the NEW transmitter

you want to store.

4. The LED ashes 3 s.

5. Hold the previously stored transmitter as

close as possible to the NEW transmitter.

6. Press button (A) on the OLD transmitter.

7. The LED lights for 1 s to conrm that the copy

procedure was successful.

9. Photocells grounding connection

Grounding connection negative terminal (COM) photocells series F4ES/F4S or other than Roger Technology

In case of malfunction, or failure to intervene in case of dimming, or continuous detection, or abnormal behaviour of the automation (gate, overhead door,

barrier, etc.), it is advisable to connect the negative terminal (COM) of the photocells to the grounding of the system.

M1 M2

COR

910

ANT

11 12 13 14 15 16 17 18 19 20 21 22 23 26 27 28 29 30 31 3224 25

COM

+LAM

+ES

+24V

COM

FT2

FT1

COS2

COS1

COM

ORO

PED

COM

COM(-)

RXTX

12 3 12

RXTX

FT1

FT2

MASTER

SLAVE 1

345

123 12345

COM(-)

All manuals and user guides at all-guidesbox.com

Other manuals for BRUSHLESS B70/2DC

Table of contents

Other Roger Technology Gate Opener manuals

Roger Technology

Roger Technology H70/200AC User manual

Roger Technology

Roger Technology BG30 Series Operating instructions

Roger Technology

Roger Technology AG-K/KB Product manual

Roger Technology

Roger Technology H21 Series Operating instructions

Roger Technology

Roger Technology SMARTY Series Operating instructions

Roger Technology

Roger Technology B70/1DC User manual

Roger Technology

Roger Technology AG/BAJ/02 Operating instructions

Roger Technology

Roger Technology SMARTY Series Operating instructions

Roger Technology

Roger Technology B70/2ML User manual

Roger Technology

Roger Technology R30/803 User guide

Roger Technology

Roger Technology CTRL User manual

Roger Technology

Roger Technology EDGE1 User manual

Roger Technology

Roger Technology BH30 Series User manual

Roger Technology

Roger Technology BH23 Series User manual

Roger Technology

Roger Technology MONOS4/220 Operating instructions

Roger Technology

Roger Technology BH30 Series Operating instructions

Roger Technology

Roger Technology B70/2ML User manual

Roger Technology

Roger Technology RL654 User manual

Roger Technology

Roger Technology R20 Series Operating instructions

Roger Technology

Roger Technology BR21 Series Operating instructions

Roger Technology

Roger Technology H70/200AC Product manual

Roger Technology

Roger Technology R20 Series User manual

Roger Technology

Roger Technology RL651 User manual

Roger Technology

Roger Technology G30/1804 Operating instructions

Popular Gate Opener manuals by other brands

Elite

Elite CSW200UL instruction manual

CAME

CAME FROG-PM4 installation manual

SOMFY

SOMFY FX230 installation manual

Aprimatic

Aprimatic ONDA 500 installation instructions

Turnstiles

Turnstiles FSW 900 manual

Erreka

Erreka BUL BL33 Quick installation and programming guide

Erreka

Erreka VULCAN S manual

Beninca

Beninca R1-2 WBV quick start guide

Erreka

Erreka VULCAN D user manual

Motorline professional

Motorline professional FORT User& installer's manual

Beninca

Beninca BOB5024 manual

AGA

AGA GATEMASTER 900 HD installation manual

Chamberlain

Chamberlain MotorLift HC280ML Mechanical installation

SOMFY

SOMFY Dexxo RTS Pro INSTALLATION INSTRUCTIONS-ILLUSTRATIONS

Cardin

Cardin BL Series manual

Westfalia

Westfalia 85 27 06 instruction manual

CAME

CAME F500 installation manual

Extel

Extel VERA quick guide