Robe onePATT User manual
Version 1.4
2
Table of contents
1. Safety instructions ......................................................................................................... 3
2. Description of the xture .............................................................................................. 4
3. Installation....................................................................................................................... 5
3.1 Mounting the onelPATT ............................................................................................. 5
3.2 Connecting the pixelPATT with the PATT Driver ........................................................ 5
4. Technical specications ................................................................................................ 7
3
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE INSTALLING THE PRODUCT .
1. Safety instructions
CAUTION!
The onePATT was designed for indoor use only.
The product is for professional use only, it is not for household use.
This product has left our premises in absolutely perfect condition. In order to maintain this condition and to
ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this manual.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this
manual or any unauthorized modication to the product.
If the device has been exposed to drastic temperature uctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation water might damage your device. Leave the device switched o until
it has reached room temperature.
The onePATT should be operated with the PATT Driver only.
The onePATT becomes hot during its operation, a
llow it to cool prior
to manipulation.
The onePATT unit never must be covered with cloth or other materials during
operation.
Refer servicing to qualied service personnel.
Warning! Risk Group 2 LED product according to EN 62471
LED light emission. Risk of eye injury. Do not look into the beam at short distance of
the of the product. Do not view the light output with optical instruments or any
device that may conncentrate the beam.
The light source contains blue LEDs.
When choosing the installation spot, please make sure that the onePATT are not exposed to extreme heat,
moisture or dust.
Operate the onePATT only after having familiarized with its functions. Do not permit operation by persons not
qualied for operating the onePATT. Most damages are the result of unprofessional operation!
Please use the original packaging if the onePATT is to be transported.
Please consider that unauthorized modications on the xture are forbidden due to safety reasons!
4
2. Description of the xture
1 - Yoke with mounting hole
2 - Tilt lock
3 - Front net cover
4 - Control Output (4-pin XLR)
5 - Control Input (4-pin XLR)
6 - Parabolic aluminium reector Control
5
3. Installation
The onePatt must be installed by a qualied electrician in accordance with all
national and local electrical and construction codes and regulations.
3.1 Mounting the onePATT
The xture can be rigged to the truss or fastened to the oor stand via a mounting yoke. The hole of diameter
of 13 mm in the yoke serves for fastening of a clamp (or a spigot) to the yoke.
Note: the spigot has to be inserted into the oor stand and always secured.
For overhead installation the onePATT has to be always secured to the truss by means of a safety wire (that
can hold at least 10 times the weight of the xture) which is fastened to the truss and around mounting yoke
of the onePATT.
3.2 Connecting the onePATTs with the PATT Driver
1. Disconnect the PATT Driver from mains.
2. Connect the onePATT to the PATT Driver by means of the 4-pin data cable.
3. Connect next 6 onePATTs to the onePATTs chain. The rst xture connected to the PATT Driver is
a pixel 1, the second xture connected to the xture 2 behaves as a pixel 2.....
Up to 7 xtures can be connected to one PATT Driver.
4. Connect the PATT Driver to mains and make desired setting of it.
ALWAYS DISCONNECT THE PATT DRIVER FROM MAINS BEFORE CONNECTING/DISCONNECTING
THE onePATT.
6
For CE only: If you do not use the original Robe Data Cable 4-pin XLR for connection between onePATT and
PATT Driver, the ferrite RRC 17-11-28-M-K5B (Robe P/N 13051799) should be installed on the 4-pin XLR cable
closely to the onePATT (the rst onePATT connected to the PATT Driver) as shown on the picture bellow.
If you use the original Robe 4-pin XLR cable, this ferrite is part of the cable and you do not need to install
another ferrite on the cable.
Ferrite RRC 17-11-28-M-K5B
7
4. Technical specications
Input voltage: 48V
Max. power consumption: 30W
Compatible control driver: PATT Driver (max. 7 onePATTs can be connected to the driver)
Light source: RGBW LED multichip
LED life expectancy: min. 20 000 hours
Typical lumen maintenance: 70% @ 20 000 hours
Optical System: 200 mm parabolic aluminium reector with high reectivity coating
Control input/output: Locking 4-pin XLR (male/female)
Mounting Points: Mounting horizontally or vertically via mounting yoke (360° tilt range)
Rigging: M12 mounting for clamp or spigot.
Operation position: any
Ingress protection: IP20 (for dry location only)
Weight: 162 kg
Max. surface temperature: 70°C (at 45°C ambient)
Maximum ambient temperature: 45 °C
Total heat dissipation (calculated):102 BTU
Min. distance from ammable surfaces: 0.2 m
Min. distance of illuminated objects: 0.2 m
Dimensions (mm)
Wiring of control input/output:
Optional accessories
(P/N 13052797) Data cable 4 pin XLR 10m, ferrite, EU
(P/N 13052798) Data cable 4 pin XLR 5m, ferrite, EU
(P/N 13052799) Data cable 4 pin XLR 10m, US
(P/N13052800) Data cable 4 pin XLR 5m, US
(P/N 17030386) Doughty Trigger Clamp
(P/N 99011963) Safety wire 35 kg
(P/N 13051799) Ferite RRC 17-11-28-M-K5B
(P/N 10055002) PATT Driver
1 - 0V
2 - Signal -
3- Signal +
4- +48V
8
Beam distribution
Copyright © 2017-2018 Robe Lighting - All rights reserved
Specications are subject to change without notice.
January 19, 2018
Made in ROBE Lighting s.r.o., Palackého 416, 757 01 Valašské Meziříčí, Czech Republic
Table of contents
Other Robe Light Fixture manuals
Robe
Robe Robin 300E Spot User manual
Robe
Robe Color Spot 575AT User manual
Robe
Robe ROBIN Spote User manual
Robe
Robe Anolis ArcSource 4 MC II User manual
Robe
Robe ROBIN T1 Fresnel User manual
Robe
Robe Beam 250XT User manual
Robe
Robe ANOLIS Eminere Inground 2 User manual
Robe
Robe ROBIN DL4S User manual
Robe
Robe ColorWash 575 AT ZOOM User manual
Robe
Robe Robin miniPointe User manual
Robe
Robe Color Wash 750 AT Tungsten User manual
Robe
Robe ROBIN T1 PC User manual
Robe
Robe DigitalSpot 7000 DT User manual
Robe
Robe scan 1200 XT User manual
Robe
Robe DigitalSpot 3000 DT User manual
Robe
Robe Eminere 1 User manual
Robe
Robe Color Wash 2500E User manual
Robe
Robe Ambiane User manual
Robe
Robe Robin 300 Plasma Wash User manual
Robe
Robe ROBIN ParFect 150 User manual
Popular Light Fixture manuals by other brands
Emos
Emos CLASSIC ZY1431T manual
Westinghouse
Westinghouse Outdoor Lighting Fixture owner's manual
Hedler
Hedler C 12 silent Operation manual
Blizzard Lighting
Blizzard Lighting Puck: CSI manual
Energetic Lighting
Energetic Lighting ELYSL-5004 Series installation instructions
Lightmaxx
Lightmaxx Shaft 5R user manual
Cooper Lighting
Cooper Lighting Halo L3232E Specification sheet
Stageline
Stageline ODW-2410RGBW instruction manual
Light Sky
Light Sky Tornado Series user manual
Lightolier
Lightolier Paralyte 2424 PLA2G9LS26U specification
Lightolier
Lightolier Lytespan 83ED17S specification
Lightolier
Lightolier Calculite CS8226 specification