Ritetemp 6020 User manual

Other manuals for 6020

1

Table of contents

Other ritetemp Thermostat manuals

Popular Thermostat manuals by other brands

EWELLY

EWELLY EW-181 manual

Prolon

Prolon T1100 Hardware guide

Computherm

Computherm Q20 operating instructions

Heatmiser

Heatmiser neoStat user manual

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA user manual

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat user manual

Saswell

Saswell SAS920XWHB-7-S-RF User manual and warranty card

Aircalo

Aircalo TFP1-ET85P2 operating manual

Honeywell

Honeywell CM721 user manual

Carrier

Carrier DEBONAIR 33CS Installation and operating instructions

Lennox

Lennox iHarmony Zone Thermostat Installation and setup guide

Gemtech

Gemtech GT7000 Operation

Rollei

Rollei Smartes 45000 manual

Sinope

Sinope TH1300RF user guide

Honeywell

Honeywell RLV4305 owner's guide

Honeywell

Honeywell Prestige 2.0 THX9421 manual

NuTone

NuTone NTBZ48 Installation & operation guide

Stelpro

Stelpro MAESTRO ASMT402AD user guide

PG 1

PG 2

Statement of use: The 6020 can be used with millivolt,

24VAC, 1 and 2 stage conventional gas/oil/elec heat, 1 and 2

stage heat pumps, 2 or 3 wire zoned hot water, zoned forced

air, 1 and 2 stage cooling and hybrid systems. 

It cannot be used with 120 volt heating systems.

HEAT

HEAT

COOL

OFF

FAN

AUTO

ON

TEMP

UP button

TEMP DOWN button

Temperature

Display HEAT/COOL

Mode Switch

Fan

Switch

Configure

Set HEAT/COOL mode switch to HEAT or COOL. The unit will display the

Room temperature. Set the Fan switch to AUTO.

Press the TEMP UP and TEMP DOWN buttons to select the desired

temperature. The TARGET icon will be displayed with your desired

temperature. (Display will return to room temp in 5 sec).

In the winter, set the system switch to HEAT to control your heating system.

In the summer, set the system switch to COOL to control your AC.

In spring and fall or when windows are open, 

you can set the system switch OFF.

Setting the FAN switch to AUTO automatically runs your system's fan during

heating and cooling.

Setting the FAN switch to ON runs your system's fan continuously even

without heating or cooling.

Operate

Farenheit/Celcius

indicator

Current Temperature

Display SET Temperature

Display

ROOM TEMP TARGET TEMP

Operation 6020

PG 4

Celsius

jumper

Reset

button

Aux Only

Heat Pump

Customer Support: 877-505-2353 Visit our webiste

www.ritetemp-thermostats.com 1611-010

F

0

/ C

0

Select

The F/C jumper is under the top cover Jumper #5. It determines which

temperature system is displayed on the LCD display. With the jumper off, the

display is Fahrenheit (default setting), with the jumper on both pins, the

display is Centigrade. When the jumper is changed, the unit must be reset

(under the top cover on the left).

Low Battery

When the batteries are low, the battery icon will flash. The two AAA

batteries in the unit need to be replaced. The HVAC system will stop

functioning when the thermostat loses power; replace batteries as soon

as you see this warning. Press RESET after replacing batteries

If you have a heat pump with auxiliary heat, and the heat pump is not

working, you can use the auxiliary heat only by moving jumper 1 [heat pump]

to jumper position 2 [ Aux only].

1234567

To set a Heat Pump's Aux only mode