ritetemp 8045 User manual
Customer Support: 888-515-2585
or Visit our website www.ritetemp-thermostats.com
Install Guide 8045
312-014
1 Location
Caution
Tools
To avoid electrical shock and to prevent damage heating system,
and thermostat, disconnect the power supply before beginningwork.
This can be done at the circuit breaker, or at the appliance.
• On replacement installations, mount the new thermostat in
place of the old one.
• On new Installations, follow the guidelines listed below.
Locate the thermostat on an inside wall, about 5 ft. (1.5m) above
the floor, and in the room with the heater to be controlled.
• Do not install where there are unusual heating conditions, such
as: in direct sunlight; near a lamp, radio, television, or a bove the
baseboard heater, or fireplace; near hot water pipes in a wa ll; or
any other heat source.
• Do not locate in unusual cooling conditions: in a draft fr om a
stairwell, door, or window; or on the wall of an unheated ro om.
• Do not locate in a damp area. This can lead to corrosion that
will shorten thermostat life.
• Do not locate where air circulation is poor, such as: in a corner
or an alcove; or behind an open door.
• Do not install until construction and painting is complete d.
• This thermostat does not require leveling.
You will need #1 Phillips screwdriver (small)
PG 1
C A U T I O N
•
Your thermostat is a precise instrument.
•
Please handle it with care.
•
Turn off electricity to the appliance before installing or
servicing thermostat or any part of the system. Do not
turn electricity back on until work is completed.
•
Do not short (jumper) across electric terminals at
control on furnace to test the system. This will damage
the thermostat and void your warranty.
•
All wiring must conform to local codes and
ordinances.
•
This thermostat is designed for use with 120-220 volt
AC systems. The thermostat should be limited to a
maximum of 16.0 amps; higher amperage may cause
damage to the thermostat.
PG 2
Good
5ft.
(1.5m)
Install Guide 8045
2 Remove old unit
3 Connect wires
Switch electricity to the heater OFF at the circuit breaker;
then proceed with the following steps.
Remove cover from old thermostat. Most are snap-on types
and simply pull off. Some have locking screws on the side or
front. These must be loosened to remove cover.
Remove the old unit from the terminal box, by unscrewing the
captive screws.
On your new thermostat, separate
Control Unit (front) from Wall Unit (back).
Grasp the front of the unit and the back of
the unit and pull apart. The ther mostat
body away from the base.
Connect the LOAD to the RED wire
and the LINE to the BLACK wire.
Twist wires together first,
then secure by twisting wire nut on.
Push the wires and wire nuts into the terminal box.
PG 3
PG 4
Caution
Make sure you note which wire is which when
you disconnect the old thermostat. Use only
UBC approved wire nuts to connect wires.
RED
TO LOAD
TO LOAD
TO LINE
TO LINE
Junction box in wall
BLACK
RED
BLACK
STAT
CAUTION HIGH VOLTAGE!
DISCONNECT POWER SUPPLY
BEFORE SERVICING
PG 6
PG 5
4 Attach Unit
Position (optional) wall plate over
junction box.
Align the 6-32 captive screws with
the threaded holes in the junction
box.
Screw the wall unit to the junction
box.
RED
TO LOAD TO LINE
BLACK
STAT
CAUTION HIGH VOLTAGE!
DISCONNECT POWER SUPPLY
BEFORE SERVICING
5 Install Batteries
The 8045 requires 2AA batteries.
On the control unit, Switch MODE
switch to OFF.
Install 2 AA alkaline batteries according
to the polarity noted in the compartment.
DO NOT USE Rechargeable Batteries.
Caution: The thermostat will go "off" if
the batteries die. This exposes your
house to unexpected heat or cold and
should be avoided.
NOTE: Replace the batteries when the
red LOW battery LED indicator blinks or
once a year.
AA
AA
Note: Do not reattach
control unit until batteries
have been inserted.
PG 8
PG 7
5 Install Batteries cont
• Replace front of control unit on the
wall unit
6 Check Unit
8045 Features
Follow these procedures to verify
you have correctly installed the
unit.
•
To check HEAT mode:
•
Set the mode switch to HEAT.
•
Turn TEMP DIAL counter clockwise to its stop.
This is the warmest setting. Allow the system 5
min to respond. Verify that heat is coming from
the system.
• Return dial to comfortable setting.
The 8045 can be used with
most 110/220 volt electric
heating devices. It provides
Line voltage control for
radiant cable, electric
baseboard, and resistive-
rated fan forced heaters
within the ratings listed.
Electrical Rating -
120/208/240 Vac;
16A resistive load
Table of contents
Other ritetemp Thermostat manuals
ritetemp
ritetemp 8035C User manual
ritetemp
ritetemp 8050C User manual
ritetemp
ritetemp 8025 User manual
ritetemp
ritetemp 6004 User manual
ritetemp
ritetemp 6036 User manual
ritetemp
ritetemp 8099 User manual
ritetemp
ritetemp 8022 Instruction Manual
ritetemp
ritetemp 6020 User manual
ritetemp
ritetemp 8050 User manual
ritetemp
ritetemp 6025 User manual
ritetemp
ritetemp 8095 User manual
ritetemp
ritetemp 6010 User manual
ritetemp
ritetemp 6008 User manual
ritetemp
ritetemp 8050C User manual
ritetemp
ritetemp 8030C User manual
ritetemp
ritetemp 8035C User manual
ritetemp
ritetemp 6005 User manual
ritetemp
ritetemp 8029B User manual
ritetemp
ritetemp 8082C User manual
ritetemp
ritetemp 8085 User manual
Popular Thermostat manuals by other brands
Saswell
Saswell SAS920XWHB-7-S-RF User manual and warranty card
Aircalo
Aircalo TFP1-ET85P2 operating manual
Honeywell
Honeywell CM721 user manual
Carrier
Carrier DEBONAIR 33CS Installation and operating instructions
Lennox
Lennox iHarmony Zone Thermostat Installation and setup guide
Gemtech
Gemtech GT7000 Operation
