Risco Agility 3 Datasheet

Installation Quick Start Guide

For detailed information please refer to the full Agility 3

Installer Manual provided on our website: www.riscogroup.com

Table of Contents

1. INSTALL THE MAIN UNIT ........................................................................................................................................3

2. KEYPAD ALLOCATION AND LANGUAGE SELECTION................................................................................................3

3. WIRELESS DEVICE ENROLLMENT (AFTER KEYPAD ENROLLMENT)...........................................................................3

4. KEYPAD PROGRAMMING.......................................................................................................................................4

5. ACCESSING INSTALLER MENU ................................................................................................................................5

. SETING THE SYSTEM CLOCK ...................................................................................................................................5

7. MEASURE NOISE AND CALIBRATE THE RECEIVER ...................................................................................................5

8. ZONES....................................................................................................................................................................5

9. KEYFOBS ................................................................................................................................................................

10. KEYPADS................................................................................................................................................................7

11. SIRENS ...................................................................................................................................................................8

12. PROGRAM COMMUNICATION MODULES ..............................................................................................................8

13. PROGRAM MS COMMUNICATION .........................................................................................................................8

14. SET UP FOLLOW-ME DESTINATIONS.......................................................................................................................9

15. SET SYSTEM PARAMETERS (CONTROLS).................................................................................................................9

1 . CUSTOMIZE THE VOICE MENU ...............................................................................................................................9

17. SET UP USERS....................................................................................................................................................... 10

18. CONNECTING THE AGILITY 3 TO THE CLOUD ........................................................................................................ 10

19. PIR CAMERA ........................................................................................................................................................ 10

20. USER DEFINITIONS AND SYSTEM OPERATION...................................................................................................... 11

21. TEST THE SYSTEM................................................................................................................................................. 11

Agility 3 Installation Quick Start Guide 3

Agility 3 Installation Quick Start Guide

Thank you for purchasing the Agility 3 Flexible Wireless Solution from RISC Group. This quick

start guide will describe the main steps for installing and programming the Agility 3 using the 2-

way wireless keypad.

1.Install the main unit

1. Disconnect the mounting bracket from the main unit by releasing the locking screws and

disconnecting the ribbon flat cable.

2. Secure the mounting bracket to the wall.

3. Connect a power wire to the power terminal located on the power supply unit of the

mounting bracket.

4. Remove the battery compartment cover screw and connect the flying leads to the battery

according to the correct polarity (Red +) (Black -).

5. n the main unit connect a phone cable, a network (IP) cable, and insert a SIM card to the

GSM/GPRS module as required (If fitted)

6. Re-connect ribbon flat cable, connect the main unit back to the mounting bracket and lock the

locking screws.

7. Power up the Agility. "Security system is on" message will be announced.

2. Keypad Allocation and Language Selection

New systems require a default language specification before any further configuration. System

language specification through “enrollment” (see below) of new system initial keypad is performed

as follows:

To define the keypad and system language:

1. After the Agility is connected to the power supply press the button on the main unit for 5

seconds. The unit beeps once and enters “Learn” mode. The LEDs light up one after the

other.

2. Send an RF signal “write message” from the 2-way LCD keypad by pressing both keys

and simultaneously for at least 2 seconds until a generic device allocation message is

broadcast and also displayed on the keypad.

3. In the displayed language menu, select the system language (and customer default) settings

and then press

Note: If the keypad lapses into sleep-mode before you have chosen the language, restore the

choose-system-language display through simultaneously pressing [*] and [9])

3.Wireless Device Enrollment (After Keypad Enrollment)

Each wireless device must identify itself to the system receiver, in a process termed “enrollment”.

Agility 3 Installation Quick Start Guide4

Enrolling the wireless devices can be performed either from the main unit, a wireless keypad or via

the Configuration Software. Enrollment can be performed by sending an RF signal from each

device, or by entering the device s unique serial code into the system.

The following steps describe quick enrollment by RF signal. For enrollment through the keypad or

via the Configuration Software refer to the installer manual.

To enroll wireless devices via RF signal:

1. If the panel is no longer in learn mode, press the button on the main unit for 5 seconds. The

unit beeps once and enters “Learn” mode. The LEDs light up one after the other.

2. Send an RF signal “write message” from each device. The unit beeps once to accept or three

times to reject. Once accepted the system sounds a local message describing the device type

and its assignment (e.g., zone 1). For future use, you may want to note down the assignment

of each device.

How to send a write message (transmission):

Wireless Device Sending Write Message

2-Way Keypad Press both keys and simultaneously for at

least 2 seconds.

Detector/Contacts Press the tamper switch for 3 seconds.

1-Way Keypad Press the key twice.

1-Way Key ob Press the button for at least 2 seconds.

2-Way Key ob Press both keys and simultaneously for at

least 2 seconds.

Smoke Detector Insert battery. Write message is sent automatically

when the tamper is closed.

Siren Press the reset switch on the siren. After a squawk

is sounded at the siren you have 10 seconds to

press on the tamper switch for at least 3 seconds.

Gas, CO detectors Press the tamper switch for 3 seconds.

2 Panic Button Key ob Press both buttons for at least 7 seconds.

Wrist Band Panic Press the button(s) for at least 7 seconds.

3. When all the devices have been enrolled, give the panel button a short press to exit “Learn”

mode. The unit beeps once and the LEDs stop flashing.

4.Keypad Programming

There are several options for programming the Agility: Configuration Software, wireless keypad, or

memory card (PTM). The following sections explain how to program Agility from the LCD keypad.

The following table describes the uses of the keypad keys during programming:

Agility 3 Installation Quick Start Guide 5

- to wake the keypad up, go back one level, exit menus, disregard

change (similar to the Esc key)

- to select (similar to the Enter key)

- to scroll

- to change selections (e.g., Y to )

- to exit the programming mode from the root menu

5.Accessing Installer Menu

1. Press to wake up the keypad.

2. Enter the installer's code 0132 (default code).

6.Seting the System Clock

To set the system clock

1. From the Engineer menu, select 5) Clock.

2. Set the Time & Date.

7.Measure Noise and Calibrate the Receiver

Once a keypad has been enrolled, you can use it to control the main unit. The first step is to measure

the background "noise" that the receiver can "hear" on the same frequency as the Agility wireless

devices. This noise may be generated by other devices operating on the same frequency nearby.

This gives an indication of whether you have chosen a good location for the main unit. Any

communication between the devices and the main unit should be stronger than this noise level.

To calibrate the noise level from the keypad

1. From within the Installer menu, use the keys to scroll between menus and the

key to select menu options. Open the 2) Testing > 1) Main Unit > 1) Noise Level > 2)

Calibrate.

2. The noise level is displayed. The lower the noise level the better the communication will be.

If the noise level seems very high, try to find a better location for the panel.

8.Zones

To program the zones

The parameters available per zone vary according to the zone type.

1. From within the Installer menu select 1) Programming > 2) Radio Device > 2) Modification >

1) Zones > 2) Parameters.

2. Use the keys select the required zone and press .

3. Set the basic parameters for each zone as follows:

•Label – provide a meaningful name

Agility 3 Installation Quick Start Guide6

Key Data Sequence

1 1 . , ' ? ! " – ( ) @ / : _ + & * #

2 2 a b c A B C

d e f E F

4 4

h i G H I

k l J K L

6 6 m n o M N O

7 7

r s P Q R S

8 8 t u v T U V

9 9 w x y z W X Y Z

0 0

Use these ke

s to to

le forwards and backwards throu

h all the

available characters.

•Partition - Use the 1, 2, or 3 keys to set the partition assignment (default is 1)

•Type – Using the arrow keys, select the desired zone type from the list and press

•Sound – Use the arrows and select the desired sound, in most cases this will be "Bell

Only"

•Advanced – includes chime, supervision, forced arm enabled, and additional

parameters for -way detectors depending on the type of detector

To test the zones

1. Use to go back up to the root of the Programming menu. Press to exit programming

and press to confirm.

. Using the keys select 2) Testing > 2) Zones > 1) Comm Test.

3. Select the zone that you wish to test.

4. Use the keys to scroll to the tested zone and observe a number representing the last

measured signal received from the detector.

Note: The signal should be higher than the measured calibrated level of the receiver previously set.

9.Keyfobs

Each keyfob can be set up to perform different system operations and control different utility

outputs. Up to eight keyfobs can be enrolled in the system. The programming options under the

parameters menu vary according to the type of the remote control, 1-Way or -Way.

To program the key ob parameters

1. From the installer menu select 1) Programming > 2) Radio Device > 2) Modi ication menu 2)

Key obs > 1) Parameters.

. Select a keyfob and press to set its basic parameters. Use the keys to scroll

between menus and the key to select menu options:

a. 1-Way keyfob basic parameters:

Agility 3 Installation Quick Start Guide

•Label – provide a meaningful name (see keypad's label table above for details)

•Partition assignment (in most cases this is left as 1)

•Button 1 functionality: (the lock button), normally ‘ rm’

•Button 2 functionality: (the Unlock button), normally ‘Disarm’

•Button 3 functionality: (panic or output control button), normally ‘Disabled’

•Button 4 (The sunken button), normally ‘Stay rm’

b. 2-Way keyfob (8-button) parameters:

•Label – provide a meaningful name (see keypad's label table above for details)

•Partition assignment (in most cases this is left as 1)

•PIN code – if required set the PIN Code for the 8-button remote control

•Panic – define whether sending a panic alarm from the remote control is permitted

(disabled by default)

• ssign the buttons to utility outputs

3. Press to go back up to the Keyfobs menu and select 2) Control.

4. Use the to toggle between Y/N to enable:

•Instant Arm: way (Full ) rm without exit delay

•tay Arm: Stay (Home) arming without exit delay

•Disarm with Code when using the 8-button remote control.

To test the Keyfobs

1. Use to go back up to the root of the Programming menu. Press to exit Programming

and then press to confirm.

2. Using keys select 2) Testing > 3) Keyfobs > 1) Comm Test

3. Select the keyfob that you wish to test.

4. Use the arrow keys to scroll to the tested keyfob and view the last received communication

level. The signal should be higher than the measured calibrated level of the receiver

previously set.

10. Keypads

Up to three keypads can be enrolled to the system (LCD or Slim).

To program the keypads

1. From the installer menu select 1) Programming > 2) Radio Device > 2) Modification menu

3) Keypads > 1) Parameters.

2. Select a keypad, press and set its basic parameters. Use the keys to scroll

between menus and the key to select menu options:

•Label – provide a meaningful name (see keypad's label table above for details)

•Emergency keys: Defines whether the emergency keys will be activated or not.

Agility 3 Installation Quick Start Guide8

•Function key (LCD keypad only): Define the operation of the keys.

•Output control: Assign outputs for the keypad's keys 1-3.

•Door bell sound (Slim keypad only): Press bell key to activate a door bell sound on

the ain Agility syste

3. Press to go back up to the Keypads enu and select 2) Control.

•RF akeup: Defines whether the keypad LCD will light up auto atically during the

entry delay ti e.

11. Sirens

Up to 3 sirens can be enrolled in the syste (internal or external).

To program the siren parameters

1. Fro the installer progra ing enu select 1) Programming > 2) Radio Device >

2) Modification enu 4) Sirens

2. Select a siren and press and set its basic para eters. Use the keys to scroll

between enus and the key to select enu option:

•Label – provide a eaningful na e

•Supervision – define if the siren is supervised

•Volume – set the volu e produced fro the siren during alar , squawk or exit/entry

ti e

•Strobe – set the strobe operation of the external wireless siren

To test the sirens

1. Use to go back up to the root of the Programming enu. Press to exit progra ing

and press to confir .

2. Using keys select 2) Testing > 5) Sirens > 1) Comm Test

3. Use the keys to scroll to the tested sirens and view the last received co unication

level. The signal should be higher than the easured calibrated level of the receiver

previously set

12. Program Communication Modules

Agility’s enus include only those co unication odules installed on-board.

1. Fro the installer enu select 1) Programming enu and select 4) Communication > 1)

Method.

2. Select each ethod (PSTN, IP and/or GSM) and define its para eters.

13. Program MS Communication

You can define up to three MS accounts and several associated para eters that define the nature of

co unication, event reporting and confir ation between the owner and the MS.

Agility 3 Installation Quick Start Guide 9

1. Use to go back up to 1) System, then > 2)Controls > 3)Communication and enable the

RC option by changing ‘N’ to ‘Y’ and pressing to confirm.

2. Use to go back up to 1) Programming > 4) Communication menu and select 2) MS.

3. Select the report type for each MS and define its parameters.

4. Define the ccount number for each MS.

5. Go through the menus to program any other communication parameters.

14. Set Up Follow-Me Destinations

Now that you have set up the methods for gility to communicate with the MS and the owner, you

can define the destinations to which event notifications will be sent.

1. Use to go back up to the 4) Communication menu and select 4) Follow Me.

2. Under 1) Define FM set each destination’s:

•Report Type (SMS, Email, Voice) (Reporting events by voice or email can be

established through different channels, depending on the hardware installed in the

system.)

•The events that will be sent, organized by category ( larms, rm/Disarm, Troubles,

GSM, Environmental, Miscellaneous)

•The restore events that will be sent

•The operations the user will be able to perform through remote connection via phone

or SMS

Note: The actual destinations (telephone numbers and email addresses) are defined outside of the

Programming menu or from the User menu.

15. Set System Parameters (Controls)

There are several system-wide parameters that define how the gility works. They are collected

under the System menu. ll these parameters are set with default values that apply for most

installations. If you wish to make a change, go through the menus to program any other system

parameter.

16. Customize the Voice Menu

Users can use the voice menu to hear local messages on system status, troubles and events, and to

control the system through remote phone operation.

1. Use to go back up to the 1) Programming menu and then 5) Audio Messages.

2. Under Local Messages, select which messages will be sounded locally (on the main unit or

the external audio unit).

3. Under Assign Message, create the phrases that will be used in place of the default messages

(e.g., instead of Zone 1 define “Front Entrance and Hall”). Refer to the Descriptor Directory

in the Installer Manual for the codes.

Agility 3 Installation Quick Start Guide10

17. Set Up Users

As the installer, you must set up the system’s users. The owner (Grand Master) will be allowed to

subsequently set their passwords.

1. Use to o back up to the 1) Programming menu and select 3) Codes.

2. Under the User option define for each user a label identifyin the user, his/her authority

level and the partitions he/she can control with his/her code.

3. Chan e the default installer code.

18. Connecting the Agility 3 to the Cloud

A ility 3 can be confi ured to be constantly connected to a server, enablin picture transfer

and user Smartphone applications. When connected to the server, the server handles all

communication between the system, service providers and web users, enablin monitorin

and control to be performed via the Web.

To enable cloud communication:

1. From the Installer menu select: 1) System > 2) Controls > 3) Communication > Cloud Enable

[ ]

To establish IP network connection to the server using the IP or GSM/GPRS module:

From the Installer menu select : 4) Communication > 5) Cloud

1) IP Address: The server IP address (riscocloud.com or that of your or anization's server)

2) IP Port: The server port is set to 33000.

3) Password — The password for server access as provided by your provider (if required).

This password MUST be identical to the Password defined in the Cloudserver. If Self-

Re istration is to be performed, do not chan e from the default.

4) Channel: Select IP Only or GSM Only dependin on the communication module in the

A ility. If GSM selected, APN Name must be entered in the GSM/GPRS menu.

Note: When in Cloud mode, the settings defined through it are applied to all reporting channels (including

MS communication and FM destination). If the cloud connection is lost/terminated and the gility

reverts to Back up mode, then the direct channel communication settings become active.

19. PIR Camera

The A ility 3 enables the use of advanced PIR-based detection cameras. This offers combined

detection with ima e recordin . Up to ei ht PIR cameras can be assi ned to the A ility 3.

To install the PIR camera detectors with the Agility 3:

1. Enroll the PIR camera as any other detector (see 3 Wireless Device Enrollment)

2. Set the PIR camera parameters as they appear under the Advanced Zone parameters

3. Set communication between the A ility 3 and the Cloud server (See 18 Connecting the Agility

3 to the Cloud-section)

4. Lo in to the Web Application with the re istered user name and password.

5. Go to the main display and select the Video option

Other manuals for Agility 3

Table of contents

Other Risco Security System manuals

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual