Riello GAS 3 Quick start guide

2915130 (5)

Installation, use and maintenance instructions

Gas burner

MODEL TYPE

GAS 3 519 T80

5130

TECHNICAL FEATURES

DIMENSIONS

Thermal output 130 - 340 kW - 112,000 - 292,000 kcal/h

Fuel Natural gas Pci 8 - 10 kWh/m

= 7000 - 8600 kcal/m

Minimum gas pressure For maximum output 11,1 mbar are needed measured at the coupling with

nil pressure in the combustion chamber and gas with calorific value of

8600 kcal/m

Maximum gas pressure 150 mbar

Electrical supply Single phase 220 V + 10% - 10% ~ 60Hz

Motor 1.85A / 220V

Capacitor 6.3 µF

Ignition transformer Primary: 1.8A / 220V - Secondary: 1 x 8 kV - 30 mA

Absorbed electrical power 0.4 kW

1– Air shutter control

2– Air shutter lock-nut

3– Wiring terminal block

4– Fair leads

5– Control box re-set button

6– Air pressure switch

7– Gas pressure test-point Fig. 1

S7495

Boiler front-plate

drilling

*Length available with special blast tube to be separately required.

Burner

160

155 M10

410 610185

*320

397

292

165

ø 140

Rp 1 1/2

D1785 S7497 S7498

5130

EQUIPMENT

FIXING TO THE BOILER

GAS SUPPLY

Quantity Burner accessories

1 Flange

1 Gasket

8 Screws

1 Flange gasket

Separate the combustion head from the

burner body by loosening the screws 1)

and 2) and withdrawing the group A) from

the holding bars 3).

Fix the group B) to the boiler front plate 4)

using the gasket 5) provided as acces-

sory.

23 5 4

S7499

1- Gas pipe line 6- Minimal gas pressure switch

2- Cock valve 7- Gas shut off valve

3- Filter 8- Burner

4- Pressure stabilizer 9- Gas safety shut off valve

5- Pressure test-point 10 - Isolator joint

43102 1

S7500

5130

WORKING RANGE

COMBUSTION CHAMBER PRESSURE - MAXIMUM OUTPUT

(in compliance with DIN 4788)

MINIMUM GAS PRESSURE - OUTPUT

Pressure

: detected at the pressure test-point 7) (fig. 1) with nil mbar into the combustion chamber.

Should the combustion chamber be pressurized, the pressure necessary will be that of the

graph plus the pressurization value.

Example

: to obtain 270 kW it is necessary a gas pressure of 8 mbar and the combustion head set as

indicated at page 7.

If the combustion chamber is pressurized at 2 mbar, the pressure detected at the test-point

7) is: 8 + 2 = 10 mbar.

If this value is too high, for very low gas pipework pressures, the gas gear 6) (page 7) could

be more open.

Do not decrease the pressure at the coupling under the values shown in the diagram.

Output

: the maximum value is obtainable with gas Pci 8600 kcal/m

CORRELATION BETWEEN GAS PRESSURE AND BURNER OUTPUT

Kcal/h

mbar

D1788

Kcal/h

mbar

D1789

5130

BURNER ELECTRICAL WIRING

(carried out in the factory)

Ignition transformer

Ionisation probe

Burner earth

CONTROL BOX

509 SE/K

Air pressure

switch

Motor Brown

Blue

Black

Capacitor

Wiring terminal block (see page 5)

S7503

5130

ELECTRICAL CONNECTIONS TO THE WIRING TERMINAL BLOCK

(to be carried out by the installer)

Notice

- Leads minimal section 1 mm

- The electric wiring carried out by the installer must be in compliance with the rules in force in the Coun-

try.

FIXING OF THE ELECTRICAL WIRES

All the electrical wires, which are to be connected to

the terminal block 3) (fig. 1) shall pass through the fair

leads 4) (fig. 1) as for this scheme.

- Single phase supply : fair lead Pg 13.5

- Adjustment thermostat : fair lead Pg 13.5

- Safety thermostat : fair lead Pg 13.5

- Gas train : fair lead Pg 13.5,

sheath ø 13

5 / 6 / 7 /8

- Pre-sheared holes

Further prospective signals or controls can be connected to the burner wiring terminal board by removing

the metal weldnuts from the pre-sheared holes and inserting a commun fair lead for the passage and the

clamping of the leads.

NOTES

- Do not exchange the neutral wire with the phase (avoid the plug-pin connection).

- Carry out a safe earth connection.

- Checkthe stopof the burner,by openingthe boilerthermostatand theburner lock-out,bydisconnecting

the lead from the flame probe.

WARNING

When closing the burner on its slide-bars, pull towards the outside the high voltage cable and the cable

of the flame detection probe, till to little tension.

gas

T6A

PE L N

1 mm2

220V ~ 60 Hz

V1 VS

V1 = Gas shut off valve

V2 = Gas safety shut off valve

S7504

S7505

5130

BURNER START-UP CYCLE

Air-purge

: loosen the screw placed on the minimal gas pressure switch mounted on the gas train

AIR PRESSURE SWITCH 6) (fig.1)

The air pressure switch setting shall be carried out after having

set all other adjustments of the burner and the air pressure

switch shall be at its lowest set-point.

When the burner is operating, increase the adjustment pressure

by turning - slowly - clockwise the knob till reaching the burner

lock-out.

Thereafter, turn the knob anticlockwise for 1 mbar and repeat

the burner start-up for checking the regularity: if lock-out inter-

venes turn the knob anticlockwise for 0.5 mbar.

CAUTION:

do not turn the ionization probe, maintain the drawing position; should it be close to the ignition elec-

trode, damage may occur to the control box amplifier.

Screw

Plug for pressure measure

Pressure switch

S7506

1 ÷ 10

mbar

Adjustment knob

S7507

0 - 1 mm

2 - 4 mm

Probe position Ignition electrode position

S7508

5130

COMBUSTION HEAD ADJUSTMENT

Two separate adjustments have to be made: air and gas.

These adjustments can be carried out when the burner is still open, during the installation (see

page 2 - Fixing to the boiler).

Air setting

Loosen the two screws 1) and move the internal

part of the combustion head 2) so that its rear

edge 3) is coincident with the desired set-point

on the plate 4). Tighten the screws 1).

Gas setting

Loosen the screw 5), move the ring 6) so that

the pointer 7) is coincident with the desired set-

point 8). Tighten the screw 5).

Attention

the set-point number is the same for air and gas

setting and is given by the following diagram.

Example:

the burner is installed on a boiler of 225 kW, assuming an efficiency of 90% the burner output should

be 250 kW. From the diagram it can be seen that the air and gas settings for this rating should be no. 4.

256

1347 S7509

Kcal/h kW

Burner output

Set-point number = for air and gas

D1793

5130

COMBUSTION CHECKS

It is advisable to not exceed 10% of CO

(gas with calorific value of 8600 kcal/m

3), in order to avoid

the risk that small changes of the adjustments due, for instance, at draught variation, may cause com-

bustion with insufficient air and consequently formation of CO.

For safety reason the value of 0.1% (one thousand p.p.m.) must not be exceeded.

IONIZATION CURRENT

The minimum current necessary for the control box operation is 3 µA.

The burner normally supplies a higher current value, so that no check is needed.

However, if a measurement of the ionization current is required, it is necessary to disconnect the

probe lead and insert a d.c. microamperometer.

BURNER START-UP

If during operation the flame shuts off, lock-out occurs within 1 sec.

Lead Probe

S7511

Normal Lock-out because no ignition

Thermostat

Motor

Ignition transf.

Start valve

Adjust. valve

Lock-out

4 s 53 s 8 s 4 s 53 s 2 s max.

D1798

5130 9

BURNER STARTING DIFFICULTIES AND THEIR CAUSES

OPERATING FAULTS

Lock-out may occur, because of: - flame failure;

- ionization probe earthed;

- air pressure switch open.

Shut-off may depend on the gas pressure switch opening.

DIFFICULTIES CAUSES

The burner goes through

the purge period normally,

the flame ignites, but the

burner goes to lock-out,

within two seconds after

the ignition if:

The ionization probe is earthed or not in contact with the flame, or

its wiring to the control box is broken, or there is a fault on its insu-

lation to earth.

The ionization current is weak (lower than 3 µA).

The burner goes to lock-

out, after the purge period,

because the flame does not

ignite; the causes may be:

The valve is passing too little gas (Low pressure in the gas pipe-

work)

The valve is defective.

The pipe has not been purged from the air.

The ignition arc is irregular or has failed.

The burner does not pass

through the pre-purge peri-

od and the control box goes

to lock-out:

The air pressure switch does not change over: it has failed or the air

pressure is too low (combustion head bad set)

Flame simulation exists (or the flame really lights).

The burner does not start at

the thermostat closing, be-

cause of:

Gas is not supplied.

The gas pressure switch does not close: incorrectly adjusted.

The air pressure switch is changed over to the operational position.

The fuse of the control box is broken.

The burner repeats the

start-up cycle without oc-

curring the lock-out:

This particular trouble is caused by the gas pipework pressure that

is very close to the value of the gas pressure switch setting, owing

to the sudden pressure decrease the valve opens and actuates -

onlytemporaneously - theopening of thepressureswitch, thereafter

the valve closes, the motor stops and the pressure increases again;

the pressure switch closes and the start-up cycle is repeated and so

forth.

To prevent this trouble, setting the gas pressure switch at a lower

value.

Other manuals for GAS 3

This manual suits for next models

Table of contents

Other Riello Burner manuals

Riello

Riello RDB3.2 VORT 58 Quick start guide

Riello

Riello Bio RLS 68/M Quick start guide

Riello

Riello COH 280 Quick start guide

Riello

Riello GAS 6/2 Quick start guide

Riello

Riello 517T80 Quick start guide

Riello

Riello G10 Quick start guide

Riello

Riello CB 512/1 Guide

Riello

Riello RS 190/M Quick start guide

Riello

Riello RLS 190/M MZ Quick start guide

Riello

Riello 970 T80 Quick start guide

Riello

Riello 40 G3RD MC Quick start guide

Riello

Riello RL 300/B MZ Quick start guide

Riello

Riello RLS 300/BP MX Quick start guide

Riello

Riello RX35 S/PV H Quick start guide

Riello

Riello RL 190/M Quick start guide

Riello

Riello Riello F10 Quick start guide

Riello

Riello G3B FIREBIRD 70K Quick start guide

Riello

Riello RS 1300/E BLU Quick start guide

Riello

Riello 3790401 Quick start guide

Riello

Riello RLS 70/EV Quick start guide

Riello

Riello RL 70/M Quick start guide

Riello

Riello DB 2 LSE FGR Quick start guide

Riello

Riello MB 412/2 User manual

Riello

Riello RG3D Quick start guide

Popular Burner manuals by other brands

True Induction

True Induction TI4B user guide

Weishaupt

Weishaupt WG20 Series manual

Carolina Cooker

Carolina Cooker M116672 owner's guide

Unigas

Unigas HTP2000 installation manual

baltur

baltur BT 250 DSG 4T manual

muenkel design

muenkel design round burner Operating and installation instructions

Ecoflam

Ecoflam Multicalor 170.1 manual

baltur

baltur BT 14 DSGW Instruction

artisan

artisan Art-SB1 Care & use manual

AESYS

AESYS TurboFire II Installation, operation and maintenance manual

IKEA

IKEA GRILLSKÄR manual

RUSTA

RUSTA SAREK manual

PROPOINT

PROPOINT 8933657 manual

baltur

baltur TBL 1000 ME Instruction manual for installation, use and maintenance

Riello Burners

Riello Burners P 200 P/G Installation, use and maintenance instructions

WLD-TEC

WLD-TEC powerjet instruction manual

MSR

MSR DRAGONFLY instruction manual

baltur

baltur COMIST 23SP Instruction