Ricoh L5160 Installation guide

2Throughput

CIP Training

L5160/L5130

CIP Training L5160/L5130

Throughput

Names and Functions of Components

This section describes the names and functions of the machine's components.

•Do not obstruct the machine's vents. Doing so risks fire caused by

overheated internal components.

Front View

DWT106

1. Center cover

Open this cover when setting media, dealing with media misfeeds, or cleaning

the platen.

2. Right cover

Open this cover when doing maintenance work such as cleaning the caps or

replacing the cleaning cartridge, etc.

3. Control panel

CIP Training L5160/L5130

Throughput

4. Media holding lever (front)

A lever to hold media on the feeding surface. Use this lever when setting media

or dealing with media misfeeds, etc. The media holding lever (front) and media

holding lever (back) work in conjunction with each other.

5. Waste ink bottle

Accumulates discharged waste ink from head cleaning, etc. To replace the waste

ink bottle.

6. Roll-up switch

Changes the rolling direction of the media. When this switch is turned off, the

media is not rolled up.

7. Roll core holder

Use to set the roll core and roll up printed roll media.

8. Media cutter

Cuts media.

9. Media output location

Outputs printed media.

10. Left cover

Open this cover when cleaning the underside of the carriage for the nozzle

surface of the print heads, media sensor, etc.

11. Ink cartridge

Set the ink cartridges of each color correctly.

12. Ink indicator

Stays lit when the ink cartridges are not set correctly or unlocked. Also, the LED

stays lit to notify when an ink cartridge is empty.

13. Attention light (option)

Notifies of errors during printing such as media misfeeds or media replacement

by lighting or flashing.

CIP Training L5160/L5130

Throughput

Rear/Side View.

DWT107

78 66

1. Vents

Prevents overheating.

2. Ethernet port

Port for connecting an Ethernet interface cable.

3. Pre-heater cover

Open this cover when setting media or cleaning the pre-heater. There are media

input locations and a media sensor inside of this cover.

4. Roll holder

Use to set roll media.

5. Roll feed unit

Pull out when setting or replacing media.

6. Media support

Use to place media temporarily when setting heavy media.

7. Handle

Use when pulling out the roll feed unit.

CIP Training L5160/L5130

Throughput

8. Media holding lever (back)

A lever to hold media on the feeding surface. Use this lever when setting media,

dealing with media misfeeds, etc. The media holding lever (front) and media

holding lever (back) work in conjunction with each other.

9. Power inlet 1

A power inlet for supplying power to the pre-heater and cure heater. Connect

the included power cord to the power socket.

10. Power inlet 2

A power inlet for supplying power to the machine. Connect the included power

cord to the power socket.

11. Main power switch

To operate the machine, the main power switch must be on. If it is off, turn the

switch on.

"Turning On the Power".

12. Media sensor

Detects the presence of media.

Inside View

DWT108

43 52

CIP Training L5160/L5130

Throughput

1. Cleaning cartridge

A maintenance cartridge that is made up of a wiper and flushing pad. Use this

cartridge when performing head cleaning. To replace the cleaning cartridge, see

"Replacing a Cleaning Cartridge".

2. Head height adjustment knob

When the machine cannot be operated due to a media misfeed etc., raise the

print heads by turning the knob, and then move the carriage out.

3. Carriage

Discharges ink onto the media, and is equipped with print heads and a media

sensor. It is possible to adjust the height of the print heads to match the thickness

of the media. To adjust the height of the print heads, see page 147 "Head

Height".

4. Capping station

Prevents nozzles from drying by capping the print heads. To clean caps, see

"Cleaning the Caps", Requests for Daily Care and Maintenance.

5. Flushing cartridge

Use when performing head cleaning or auto maintenance. To replace the

flushing cartridges, see page 242 "Replacing a Flushing Cartridge".

6. Media guide

Set media in accordance to its width. Set the media so that both edges pass under

the media guides.

7. Platen

This is the media feeding surface (printing range). Clean this area if the back of

the printed media becomes dirty. See "Cleaning the Platen", Requests for Daily

Care and Maintenance.

8. Vacuum hole

Sucks media and prevents it from rising.

9. Feed roller

Feeds media.

10. Pinch roller

Holds down set media from above.

Symbols for Power Switch

Symbols for power switch that are used for this machine are as follows:

• : POWER ON

• : STANDBY

Heater

There are 4 heaters built into this machine to maintain print quality. The location of

each heater and its function is as follows.

CIP Training L5160/L5130

Throughput

•The media feeding surface is hot while the heater is heated. When opening the

center cover or replacing media, lower the temperature of the heater and make

sure the temperature of the media feeding surface has lowered sufficiently

before working.

•When replacing thin media, lower the temperature of the heater. If replacing

media when the media feeding surface is hot, it may cause the media to affix to

the feeding surface as well as wrinkles or warping to occur.

DWT113

1. Media feed direction

2. Pre-heater

Pre-heats media before printing and suppresses sudden changes in the

temperature on the platen.

3. Print heater

Heats media during printing and increases image quality.

4. Post-heater

Drys ink from below media after printing.

5. Cure heater

Heats and cures ink from above the media with far-infrared rays.

CIP Training L5160/L5130

Throughput

Guide to Functions of the Attention Light

•Do not push or pull the attention light when it is installed to the machine. Doing so

may result in damage or malfunction of the attention light or the machine.

CUV121

The attention light notifies the user

by light when there is a media jam

or no media is left. The colors of

the lamp and their meanings are as

follows:

Lamp Status

The bottom lamp lights blue. Printing

The bottom lamp flashes blue. Data in

The top lamp lights red. Error occurred

(Example)

• When the service call message appears

• Media jam

• Out of media

• Out of ink

Read the message on the display panel, and then

take appropriate action.

Lamp Status

The top lamp flashes yellow. Warning

(Example)

• Ink has nearly run out.

• Waste ink bottle is nearly full.

Read the message on the display panel, and then

take appropriate action.

•

The main power switch is on the left rear of the machine. When this switch is turned on, the main power

turns on and the main power indicator on the right side of the control panel lights up. When this switch is

turned off, the main power turns off and the main power indicator on the right side of the control panel

goes out. When this is done, machine power is off.

The machine has two power cords. Each power cord plug must be connected to a different power source

that has an independent circuit breaker.

Normally, do not turn off the power of the machine. When the power is turned off for long periods, the

auto maintenance function is not performed successfully. When unavoidably turning off the power or

when removing the power plug, turn the power back on as soon as possible. If the auto maintenance

function does not run, a dried print head may cause nozzles to clog, possibly leading to damage.

Turning On the Power

•This machine automatically enters Sleep mode if you do not use it for a certain amount of time.

1. Make sure the power cord is ﬁrmly plugged into the wall outlet.

2. Press the main power switch on the left rear of the machine.

Do not push the main power switch repeatedly.

When you push the main power switch, wait at least 10 seconds after it is conﬁrmed that the main

power indicator has lit up or gone out.

If the main power indicator does not light up or go out in 5 minutes after you push the main power

switch, contact your service representative.

CIP Training Pro C7200 series

Throughput

Turning On/Off the Power

The main power indicator on the control panel lights up.

DWT114

3. Turn on the power of the computer connected to the machine.

Other manuals for L5160

This manual suits for next models

Table of contents

Other Ricoh Printer manuals

Ricoh

Ricoh B245-62 Manual

Ricoh

Ricoh Aficio GX7000 User manual

Ricoh

Ricoh fax3900l User manual

Ricoh

Ricoh PRO C9100 User manual

Ricoh

Ricoh AP2600 User manual

Ricoh

Ricoh Aficio AP600LU User manual

Ricoh

Ricoh Pro 8100S User manual

Ricoh

Ricoh Lef-C1 Installation guide

Ricoh

Ricoh SP 210 User manual

Ricoh

Ricoh Aficio SP 3410DN Installation instructions

Ricoh

Ricoh FAX2700L User manual

Ricoh

Ricoh Infoprint 1754 Express User manual

Ricoh

Ricoh AP610N - Aficio B/W Laser Printer User manual

Ricoh

Ricoh Aficio SPC222SF User manual

Ricoh

Ricoh PRO C7200 User manual

Ricoh

Ricoh Aficio MP1812L User manual

Ricoh

Ricoh Pro 8200s User manual

Ricoh

Ricoh Aficio 3228C User manual

Ricoh

Ricoh C220N - Aficio SP Color Laser Printer User manual

Ricoh

Ricoh AficioSP C410DN User manual

Ricoh

Ricoh J2SS Service manual

Ricoh

Ricoh Aficio SP C320DN User manual

Ricoh

Ricoh DDP User manual

Ricoh

Ricoh SG 7100DN User manual

Popular Printer manuals by other brands

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series quick start guide

Evolis

Evolis Elypso user guide

Kyocera

Kyocera FS-9530DN specification

Canon

Canon LASER SHOT LBP-1210 Specifications

Samsung

Samsung BIXOLON SRP-350plusF user manual

Canon

Canon PIXMA PRO-1 Series Getting started

Canon

Canon PIXMA G3560 Online manual

Dell

Dell Color Laser Printer 2130cn user guide

Tektronix

Tektronix Phaser 840 user guide

Epson

Epson ET-7750 Programming guide

Canon

Canon CLBR 460ps Service manual

Eltron

Eltron P210 Guide manual

Epson

Epson SC-F7100 series user guide

Epson

Epson Stylus C40UX Service manual

Canon

Canon imagePASS-A2 Service guide

Canon

Canon S820D user guide

IRA3D

IRA3D POETRY4 Original instructions