Ricoh S7 D3DS Quick start guide

Double-feed Kit S7

Machine Code:D3DS

Field Service Manual

Ver 1.0

Latest Release: Nov, 2016

Initial Release: Nov, 2016

Table of Contents

1. Install.................................................................................................................................................................................. 2

Double-feed Kit S7 D3DS..................................................................................................................................................... 2

Accessories........................................................................................................................................................................ 2

Installation.......................................................................................................................................................................... 3

1.Install

Install

Double-feed Kit S7 D3DS

Accessories

No.

Description

Q’ty

1 Double-feed Sensor 1 (Emitter) 1

2 Double-feed Sensor 2 (Receiver) 1

3 Double-feed Sensor Board 1

4 Clamp 1

5 Long Harness (2-pin) 1

6 Long Harness (7-pin) 1

7 Shielded Harnesses 1

8 Short Harness (13-pin) 1

9 Screws M3x6 4

10 Screws M3x8 2

1.Install

Installation

Remove ADF Covers

1. Set the saddle clamp on the double-feed sensor board.

2. At the back of the machine, remove the cap and screw from the rear cover.

3. Raise the feed cover, and then remove the screw from the top edge of the rear cover.

4. Press the tab [A] on the end of the rear cover to release the cover, and then rotate the cover [B] down slowly.

1.Install

5. Disconnect the bottom tabs, and then remove the rear cover.

6. At the front, raise the ADF slightly.

7. Disconnect the top edge of the front cover. The embossed arrow [A] shows which direction to slide the cover to

unlock the tabs..

1.Install

8. Push the front cover [A] to the left, and then remove it [B].

9. Lower the ADF.

Remove Feed Cover, Upper Guide

1. At the left rear corner of the ADF, disconnect and free the shielded harnesses.

1.Install

2. At the front, remove the pivot screw.

3. Disconnect the hinge arm.

4. Carefully disconnect the cover at the rear [A].

5. At the front, disconnect the hinge arm [B].

1.Install

6. Remove the feed cover.

7. Lay the feed over on a flat clean surface as shown, and then disconnect the upper guide.

8. Release the edge of the upper guide from the posts.

9. Swing the upper guide up, and then remove it.

Remove Original Shielded Harnesses

1. Turn the upper guide [A] upside down.

1.Install

2. Disconnect the ground wire [B].

3. Remove the sensor bracket.

4. Disconnect the skew correction sensor [A] (white connector).

5. Disconnect the separation sensor [B] (black connector).

•These sensor harnesses must be re-connected as shown.

Table of contents

Other Ricoh Printer Accessories manuals

Ricoh

Ricoh AP600N User manual

Ricoh

Ricoh 3800H Operating manual

Ricoh

Ricoh 3800C Series Operating manual

Ricoh

Ricoh PB2030 Quick start guide

Ricoh

Ricoh Aficio 1045 Series Reference guide

Ricoh

Ricoh DDP 92 User manual

Ricoh

Ricoh Aficio 7000 Series User manual

Ricoh

Ricoh ADF DF7010 Quick start guide

Ricoh

Ricoh CS4010 Quick start guide

Ricoh

Ricoh 402011 - Network Scanning Unit Type A Scanner... User manual

Ricoh

Ricoh Aficio C3000 User manual

Ricoh

Ricoh PJ Interactive Kit Type3 Original instructions

Ricoh

Ricoh Priport DX 4640PD User manual

Ricoh

Ricoh TCRU/ORU Operating instructions

Ricoh

Ricoh M379 User manual

Ricoh

Ricoh Aficio 3228C User manual

Ricoh

Ricoh Aficio AP4510 User manual

Ricoh

Ricoh Aficio MP W3600 User manual

Ricoh

Ricoh TK2000 User manual

Ricoh

Ricoh D392 Installation guide

Ricoh

Ricoh E-25C Quick start guide

Ricoh

Ricoh 3800C Series User manual

Ricoh

Ricoh LCIT RT5100 Quick start guide

Ricoh

Ricoh E-43A Quick start guide

Popular Printer Accessories manuals by other brands

Star Micronics

Star Micronics TSP800 Series install guide

REA

REA JET HR pro 2K user manual

HP Laserjet,Color Laserjet 4si user guide

oliser

oliser MS 45 instructions

Roland

Roland DU2-64 Supplementary manual

Xerox

Xerox EFI EXP6000 Specification sheet

Canon

Canon Finisher-T1 Service manual

Sharp

Sharp FO-1MK Service manual

Labelmate

Labelmate PM-300 user manual

Epson

Epson T6248 Product information sheet

Epson

Epson OT-BZ20 user manual

Canon

Canon TonerRobot EP-27 instruction manual

GBC

GBC 16 Series user guide

Canon

Canon INNER 2-WAY TRAY-E1 INSTALLATION PROCEDURE

Develop

Develop SD-509 installation manual

Kyocera

Kyocera KM-6230 Instruction handbook

Triumph Adler

Triumph Adler DF-710 Instruction handbook

Citizen

Citizen CBM-202PC Series user manual