Ricoh Ri 100 Quick start guide

RICOH Ri 100 Notes for Wireless LAN Users

This manual explains how to connect the machine to the network via a wireless LAN interface in

the infrastructure mode.

In the infrastructure mode, communication is established via a wireless LAN access point.

DSA072

Ad hoc mode is not supported.•

Ethernet and wireless LAN settings cannot be enabled at the same time.•

Checking Your Wireless Network Environment

Before using the wireless LAN, configure the following settings and make the check.

1. Before configuring the wireless LAN settings, configure the machine’s IP address or

make DHCP enabled.

For details about configuring the machine's IP address, see "Preparing for Printing", Operat-

ing Instructions .

2. Check that the access point is operating.

CHV600

3. Plug the wireless LAN cable into the Ethernet port before configuring the wireless

LAN settings.

DSA343

Selecting the Configuration Method

The configuration method depends on the access point being used.

"Easy Setup" is a function for automatically configuring the wireless LAN settings. The actual

name of the function may vary depending on the access point being used. See the access point

manual.

Page 3

”Easy Setup Using the

Push Button”

Page 7

”Manual setting”

Easy Setup

“PBC Method”

Easy Setup

“PIN Method” Manual setting

Does the access point support "Easy Setup" of the wireless LAN?

Is there a push button

on the access point?

Page 5

”Easy Setup Using a

PIN Code”

YesNo

Yes No

CHV626

Manual setting:• Page 7 "Configuring Settings Using Web Image Monitor"

Manual setting:• Page 12 "Configuring Settings Using the Control Panel"

Easy Setup Using the Push Button

1. Turn the machine on.

DSB151

2. Press the [ /Menu] key.

3. Press the [ ] or [ /Menu] key to display the [Host Interface] menu, and then press the

[#Enter] key.

<Menu>

Host Interface

4. Press the [ ] or [ /Menu] key to display [Wireless LAN], and then press the [#Enter]

key.

Wireless LAN

5. Press the [ ] or [ /Menu] key to select [Easy Setup], and then press the [#Enter]

key.

Easy Setup

6. Press the WPS button on the access point.

WPS

CHV607

7. Press the [ ] or [ /Menu] key to select [PBC Method], and then press the [#Enter]

key.

PBC Method

If the access point cannot be detected within 120 seconds, the search session expires.

If the connection attempt has failed, press the [#Enter] key again. If the problem persists,

check whether the access point is working properly.

Configuration is complete when connection to the access point is confirmed.

8. After you have made all the settings, press the [Escape] key.

9. Print the configuration page to check whether the machine has successfully con-

nected to the access point.

Load the print media in the cassette.

If the wireless LAN signal is reported as being unavailable (0%) on the configuration page,

the machine is not connected to the access point.

How to print the configuration page

the [ /Menu] key [List/Test Print] [Config. Page] the [#Enter] key

Easy Setup Using a PIN Code

1. Turn the machine on.

DSB151

2. Press the [ /Menu] key.

3. Press the [ ] or [ /Menu] key to display the [Host Interface] menu, and then press the

[#Enter] key.

<Menu>

Host Interface

4. Press the [ ] or [ /Menu] key to display [Wireless LAN], and then press the [#Enter]

key.

Wireless LAN

5. Press the [ ] or [ /Menu] key to select [Easy Setup], and then press the [#Enter]

key.

Easy Setup

6. Press the [ ] or [ /Menu] key to select [Display PIN], and then press the [#Enter]

key.

Display PIN

7. Check the machine's PIN.

8. Enter the machine's PIN on the access point web page.

CHV609

For details, see the manual supplied with the wireless LAN access point.

9. Execute WPS (PIN system) from the access point's web page.

10. Press the [Escape] key.

11. Press the [ ] or [ /Menu] key to select [PIN Method], and then press the [#Enter]

key.

PIN Method

If the connection attempt has failed, press the [#Enter] key again. If the problem persists,

check whether the access point is working properly.

Configuration is complete when connection to the access point is confirmed.

12. After you have made all the settings, press the [Escape] key.

13. Print the configuration page to check whether the machine has successfully con-

nected to the access point.

Load the print media in the cassette.

If the wireless LAN signal is reported as being unavailable (0%) on the configuration page,

the machine is not connected to the access point.

How to print the configuration page

the [ /Menu] key [List/Test Print] [Config. Page] the [#Enter] key

Manual Setting

If you cannot confirm the settings of the access point being used or the access point does not

support WPS, configure the wireless LAN settings manually.

You can configure the settings using Web Image Monitor or the control panel. This manual mainly

explains configuration using Web Image Monitor.

Configuring Settings Using Web Image Monitor

Connect the machine and computer with an Ethernet cable before configuring the settings.•

DSA345

Check the security method employed by the access point being used.•

Check the machine's IP address.•

the [ /Menu] key [Host Interface] [Network Setup] [IPv4 Address]

1. Launch the Web browser.

2. In the address bar, enter "http://(machine's IP address or host name)/".

3. Click [Administrator Login].

DSB201

A dialog box for entering the user name and password appears.

4. Enter the user name and password, and then click [OK].

If this is the first time to log in, enter "admin" as the user name and leave the password

blank.

5. In the menu area, click [Settings].

6. Click [Wireless LAN Settings].

7. Specify the wireless LAN settings.

If the security method is WEP

DSB202

1. Enter the network name of the access point.

2. Select [WEP].

3. Enter the password for the access point, and then select the [Apply] check box.

If the security method is WPA

DSB203

1. Enter the network name of the access point.

2. Select [WPA].

If the WPA authentication method is WPA-PSK or WPA2-PSK•

DSB205

1. Select [WPA-PSK] or [WPA2-PSK].

2. Enter the PSK (Pre-Shared Key), and then select the [Apply] check box.

Configure other settings if needed.

Other manuals for Ri 100

Table of contents

Other Ricoh All In One Printer manuals

Ricoh

Ricoh Aficio SP W2470 User manual

Ricoh

Ricoh Aficio MP C3500 User manual

Ricoh

Ricoh AFICIO 1055 User manual

Ricoh

Ricoh A151 Quick start guide

Ricoh

Ricoh Aficio 3260C User manual

Ricoh

Ricoh Pro C5100 Series User manual

Ricoh

Ricoh Aficio 2238C User manual

Ricoh

Ricoh M C240FW User manual

Ricoh

Ricoh Aficio 3025 Instruction and safety manual

Ricoh

Ricoh SP 203 SF User manual

Ricoh

Ricoh 2015 User instructions

Ricoh

Ricoh 6513 User manual

Ricoh

Ricoh Aficio SP 5200S User manual

Ricoh

Ricoh Brz-P1 Series Installation guide

Ricoh

Ricoh BizWorks 406e User manual

Ricoh

Ricoh 7025 User manual

Ricoh

Ricoh Aficio MP 2352 Installation guide

Ricoh

Ricoh Aficio MP C4502 User manual

Ricoh

Ricoh A193 User manual

Ricoh

Ricoh SP 1000S User manual

Ricoh

Ricoh FT9105 User manual

Ricoh

Ricoh 3045 - Aficio B/W Laser User manual

Ricoh

Ricoh Pro C900 User manual

Ricoh

Ricoh Aficio MP C3001 User manual

Popular All In One Printer manuals by other brands

Triumph Adler

Triumph Adler DC 2016 Instruction handbook

Epson

Epson WorkForce WF-2510 Basic guide

Epson

Epson Stylus Scan 2000 Product information guide

Epson

Epson PictureMate Snap PM 240 Start here

Konica Minolta

Konica Minolta bizhub C35 user guide

Brother

Brother MFC-J430w user guide

Konica Minolta

Konica Minolta BIZHUB 558 Quick reference guide

Lexmark

Lexmark MX710 Series setup sheet

Brother

Brother MFC-9760 owner's manual

Lexmark

Lexmark XC8155 user guide

Lexmark

Lexmark X642E Service manual

Sharp

Sharp MX-2310U Start guide

Aficio

Aficio 200 manual

Canon

Canon ImageCLASS 2300 setup sheet

Lexmark

Lexmark X925 Installation

Brother

Brother Business Smart MFC-J4510dw manual

Epson

Epson Stylus CX8400 Series Brochure & specs

Oce

Oce VarioLink 5022 user guide