Renishaw MCU5 User manual
MCU1,MCUlite‐2andMCU5user'sguide
Part Number H-1000-5067-08-A
Pa
g
e 1 of 31MCU1, MCUlite-2 and MCU5 user's
g
uide
02/01/2013file://C:\TEMP\~hhC0D2.htm
Disclaimer&trademarks
This document may not be copied or reproduced in whole or in part, or transferred to any other media
or language, by any means, without the prior written permission of Renishaw.
The publication of material within this document does not imply freedom from the patent rights of
Renishaw plc.
Disclaimer
RENISHAW HAS MADE CONSIDERABLE EFFORTS TO ENSURE THE CONTENT OF THIS
DOCUMENT IS CORRECT AT THE DATE OF PUBLICATION BUT MAKES NO WARRANTIES OR
REPRESENTATIONS REGARDING THE CONTENT. RENISHAW EXCLUDES LIABILITY,
HOWSOEVER ARISING, FOR ANY INACCURACIES IN THIS DOCUMENT.
Trademarks
RENISHAW®, REVO and the probe emblem used in the RENISHAW logo are registered trademarks
of Renishaw plc in the UK and other countries.
apply innovation is a trademark of Renishaw plc.
All other brand names and product names used in this document are trade names, service marks,
trademarks, or registered trademarks of their respective owners.
© 2003 - 2011 Renishaw plc. All rights reserved.
Renishaw part no: H-1000-5067-08-A
Issued: 01 2011
Pa
g
e 2 of 31MCU1, MCUlite-2 and MCU5 user's
g
uide
02/01/2013file://C:\TEMP\~hhC0D2.htm
FCC
Informationtouser(47CFR:2001part15.19)
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
Informationtouser(47CFR:2001part15.105)
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses and can radiate radio frequency energy and, if not used in accordance
with this installation guide, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case you will be
required to correct the interference at your own expense.
Informationtouser(47CFR:2001part15.21)
The user is cautioned that any changes or modifications, not expressly approved by Renishaw plc or
authorised representative, could void the user’s authority to operate the equipment.
Pa
g
e 3 of 31MCU1, MCUlite-2 and MCU5 user's
g
uide
02/01/2013file://C:\TEMP\~hhC0D2.htm
ECdeclarationofconformity
RENISHAW plc of New Mills, Wotton-under-Edge, Gloucestershire, GL12 8JR, England declares that:
1. We are the manufacturers of the equipment identified by the following particulars:
2. The equipment complies with the protection requirements of directive 89/336/EEC as amended.
3. The equipment conforms to the following standards -
The full EC declaration of conformity is held in the Renishaw technical file. A copy is available on
request.
Equipment type: Manual control unit
Model: MCU1 / MCU5
BS EN 61326:1998/ Electrical equipment for measurement
A1:1998/ A2:2001/ Control and laboratory use
A3:2003 EMC requirements Immunity to annex A - industrial locations.
Emissions to class A (non-domestic) limits.
BS EN 60204-1: 2006 Safety of machinery - electrical equipment of machines -
Part 1 General Requirements.
Renishaw plc declare that the product:
has been manufactured in conformity with the following standards:
and that it complies with the requirements of the following directives:
Name: MCUlite-2
Description: Manual control unit
BS EN 61326-1:2006 Electrical equipment for measurement,
control and laboratory use
- EMC requirements -
Part 1: General requirements
Immunity to Table 2 - industrial locations.
Emissions to Class A - industrial locations.
BS EN 60204-1: 2006 Safety of machinery - electrical equipment of machines -
Part 1 General Requirements.
2004/108/EC Electromagnetic compatibility (EMC)
2006/95/EC Low voltage
Pa
g
e 4 of 31MCU1, MCUlite-2 and MCU5 user's
g
uide
02/01/2013file://C:\TEMP\~hhC0D2.htm
The above information is summarised from the full EC Declaration of Conformity. A copy is available
from Renishaw on request.
Pa
g
e 5 of 31MCU1, MCUlite-2 and MCU5 user's
g
uide
02/01/2013file://C:\TEMP\~hhC0D2.htm
Care&warranty
Careofequipment
Renishaw probes and associated systems are precision tools used for obtaining precise
measurements and must therefore be treated with care.
ChangestoRenishawproducts
Renishaw reserves the right to improve, change or modify its hardware or software without incurring
any obligations to make changes to Renishaw equipment previously sold.
Warranty
Renishaw plc warrants its equipment for a limited period (as set out in our standard terms and
conditions of sale) provided that it is installed exactly as defined in associated Renishaw
documentation.
Prior consent must be obtained from Renishaw if non-Renishaw equipment (e.g. interfaces and/or
cabling) is to be used or substituted. Failure to comply with this will invalidate the Renishaw warranty.
Claims under warranty must be made from authorised service centres only, which may be advised by
the supplier or distributor.
Pa
g
e 6 of 31MCU1, MCUlite-2 and MCU5 user's
g
uide
02/01/2013file://C:\TEMP\~hhC0D2.htm
References&associateddocuments
It is recommended that the following documentation be referred to when installing an MCU.
Renishawdocuments
Document number Title
H-1000-5223 UCC2 installation guide
H-1000-5109 UCClite-2 installation guide
H-1000-5198 UCCFusion installation guide
External documents
National and international standards including the following may be applicable to the finished machine
or installation:
BS EN ISO 12100:2003 parts 1 and 2 Safety of Machinery - Basic Concepts, General Principles for
Design.
BS EN 60204-1:2006 Safety of machinery - Electrical equipment of machines - Part 1: General
requirements.
Pa
g
e 7 of 31MCU1, MCUlite-2 and MCU5 user's
g
uide
02/01/2013file://C:\TEMP\~hhC0D2.htm
Safety
Environmentalrequirements
Indoor use IP40
Altitude up to 2000 m
Operating
temperature +10 °C to +40 °C
Storage temperature -25 °C to +70 °C
Relative humidity Relative humidity 80% maximum (non-condensing) for temperatures up to
+31 °C.
Linear decrease to 50% at +40 °C
Pollution degree Pollution degree 2
NOTE: For safety reasons it is recommended that the optional joystick docking station is
mounted outside of the working area of the CMM.
Pa
g
e 8 of 31MCU1, MCUlite-2 and MCU5 user's
g
uide
02/01/2013file://C:\TEMP\~hhC0D2.htm
Manualcontrolsystemsdescription
NOTE: Unless otherwise specified, all information supplied in this guide applies to the MCU1,
MCUlite-2 and the MCU5.
MCU1
The manual control unit (MCU1) is a comprehensive CMM joystick controller designed for use with
Renishaw’s universal CMM controller range. Including the functionality of both the Renishaw
standard UCC joystick interface and Renishaw PHC10 hand control unit (HCU1), the MCU1 connects
to the UCC controllers as shown.
MCUlite‐2
The MCUlite-2 is a basic low cost joystick . It has the controls necessary to control a 3-axis touch-
trigger CMM but without the sophistication of a LCD display screen.
MCU5
The MCU5 is a derivative of the MCU1 joystick, the only difference being the addition of a STOP
switch on the membrane keypad.
The MCU5 has been developed for use with Renishaw’s REVO dynamic measuring head and probe
system, where the STOP switch is provided to augment the ESTOP switch. The ESTOP switch has
to cut the motor power to all the axes, including the two REVO axes. This is not always appropriate
as the REVO A axis will drop to 0° by gravity. Operation of the STOP switch will bring the CMM to a
fast stop but the motors will remain engaged in the ‘hold’ state.
NOTE: The MCUlite-2 is not compatible with UCC1.
Pa
g
e 9 of 31MCU1, MCUlite-2 and MCU5 user's
g
uide
02/01/2013file://C:\TEMP\~hhC0D2.htm
NOTE: The MCU5 is not compatible with UCC1.
Pa
g
e 10 of 31MCU1, MCUlite-2 and MCU5 user's
g
uide
02/01/2013file://C:\TEMP\~hhC0D2.htm
This manual suits for next models
2
Table of contents
Other Renishaw Controllers manuals
Renishaw
Renishaw UCClite-2 User manual
Renishaw
Renishaw PHC10-3 PLUS User manual
Renishaw
Renishaw UCC T3 PLUS User manual
Renishaw
Renishaw UCC T3-2 User manual
Renishaw
Renishaw UCC S5 REVO-2 User manual
Renishaw
Renishaw UCC MMI-2 User manual
Renishaw
Renishaw UCC1 User manual
Renishaw
Renishaw UCC MMI User manual
Renishaw
Renishaw UCC dynamic mapping tool User manual
Renishaw
Renishaw UCC PI 80 User manual
Popular Controllers manuals by other brands
Digiplex
Digiplex DGP-848 Programming guide
YASKAWA
YASKAWA SGM series user manual
Sinope
Sinope Calypso RM3500ZB installation guide
Isimet
Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions
LSIS
LSIS sv-ip5a user manual
Rockwell Automation
Rockwell Automation 1769-L31 installation instructions
