Redroad G10 User manual
Robot Self-cleaning Vacuum Mop G10 User Manual
Manuel d'utilisation du robot aspirateur auto-nettoyant G10
Bedienungsanleitung für selbstreinigenden Wisch- und Saugroboter G10
Manuale d’uso del Robot aspirapolvere autopulente G10
Manual de usuario de aspiradora robot autolimpiante G10
Instrukcja obsługi automatycznego robota czyszczącego G10
Робот-швабра с самоочисткой G10 Руководство пользователя
Kendi Kendini Temizleme Vakumlu Paspas Robotu G10 Kullanım Kılavuzu
셀프 클리닝 로봇 진공청소기 G10 사용자 설명서
1
23
45
67
89
111
133
155
177
2
Safety Instruction
Battery and charging
• WARNING: For the purposes of recharging the battery, only use
the detachable supply unit provided with this appliance.
• Do not disassemble, repair or modify the battery or self-cleaning
station without permission.
• Do not wipe or clean the charging shrapnel of the self-cleaning
station with wet cloth or wet hands.
• Do not place the self-cleaning station near the heat sourced
(such as radiator).
• Please don’t abandon the waste batteries at will and hand them
over to professional recycling agencies for disposal.
• If it is not used for a long time, please turn off the vacuum-mop
after fully charging and put it in a cool and dry place. It is
recommended to charge it at least once a month to avoid battery
damage. Notes:
• When disassembling the battery, make sure that the battery is
exhausted and operated away from the self-cleaning station.
• Please disassemble the whole battery pack together, and do not
damage the battery pack casing, so as to avoid short circuit or leakage
of dangerous substances.
• If you touch exudate flows out from the battery incautiously, please
rinse with plenty of water and go to the hospital promptly.
Chemical substances contained in the built-in lithium ion battery of
this product will pollute the environment.
Please invite professionals to remove it before scrapping, and
hand it over to a professional battery recycling station for
centralized disposal.
Instructions on environmental protection
Steps to disassemble the battery
The following information is only applicable when discarding this
sweeping robot, and is not a daily operation instruction:
1. Let the sweeping and mopping robot run until it is low in power
and cannot be cleaned without touching the self-cleaning station.
2. Turn off the sweeping robot.
3. Disassemble the bottom shell of the sweeping and mopping
robot.
4. Press the buckle, pull out the connector plug of the battery and
take out the battery.
3
Accessories already installed on the self-cleaning station:
Filter
(Installed on the
dust compartment)
Vacuum-mop
Other accessories:
Main brush Main brush cover Side brush
Accessories already installed on the vacuum-mop:
Dust compartment
Product Introduction
Side brush
(For replacement)
Fresh water tank Dirty water tank Dirty water filter
Self-cleaning station
Dust brush
Power cord
Mop
Note: Illustrations of product, accessories,
and user interface in the user manual are
for reference purposes only. Actual
product and functions may vary due to
product enhancements.
Mop
(For replacement)
On-off button
Press for 3s, power-on or power-off
Press for a short period of time, cleaning or pausing
Collision sensor
Edge IR sensor
On-off button
Recharging sensor
Recharging button
Indicator light
Cover
Product Introduction
Charging electrodes
Laser radar
Vacuum-mop
4
Main brush
Universal wheel
Ultrasonic sensor
Left wheel/Right wheel
Cliff sensor
Side brush
Main brush cover
Vibration mop bracket
(Non-detachable)
Recharging button
In operation state, short press, pauses cleaning
In pause state, short press, start recharging
In charging state, short press, stop recharging
Instructions to the indicator light status of the vacuum-mop
The vacuum-mop is normal
In charging
In recharging / firmware upgrading
Vacuum-mop Wi-Fi is offline
The vacuum-mop is abnormal
Off/sleepy
White light is always on
White light breathes
White light flashes
Yellow light is always on
Yellow light flashes
The light of vacuum-mop is off
Product Introduction
5
Self-cleaning station (Near the wall)
Dirty water filter
Cleaning brush
Drainage hole
Dust compartment release button
Dust compartment cover
Filter
Vibration mop bracket
Dust compartment
Vibration mop bracket
Vacuum-mop
Wi-Fi indicator light
Blue light stays on for 2s and then goes
out: Wi-Fi is connected
Blue light flashes: Wi-Fi connection in
progress / firmware upgrade in progress
Yellow light flashes: Wi-Fi waits for
connection
Reset button
Press for 3s, reset the system
Press for 10s, recover the system
Note: dust compartmentes should be installed in both the cleaning mode and the
sweeping and mopping mode, otherwise the vacuum-mop can’t be started.
Remove anti-collision protection strip
Before use, be sure to remove the anti-collision protection strips on
both sides of the vacuum-mop.
self-cleaning station is normal
In cleaning
self-cleaning station is abnormal
White light is always on
White light flashes
Yellow light flashes
6
Dirty water tank
Cleaning tray
Fresh water
tank
Cover of cleaning
station
Product Introduction
Sweeping/mopping
button
Recharging cleaning
button
Recharging tray
Cleaning brush
Place the self-cleaning station against the wall and
connect the power cord
Installation
＞0.5m
＞0.5m
＞1.5m
Instructions to the indicator light status of the self-cleaning
station
Notes:
• Do not expose the self-cleaning station to direct sunlight.
• Please ensure a space of at least 0.5m on both the left and right sides of the
self-cleaning station, and a space of at least 1.5m in front of it.
• Pay attention to the power cord, otherwise it may be dragged by the
vacuum-mop, causing the self-cleaning station to move or power off.
• The fresh water tank, dirty water tank, and dirty water filter must be installed in
place.
Notes:
•
For the first time of charging, please use it after fully charging to protect
the battery.
•
When vacuum-mop fails to power on due to low battery level, place it on
self-cleaning station for charging.
•
The vacuum-mop will start up automatically after connected to the
self-cleaning station, and cannot be shut down during charging.
Sweeping/mopping button:
In stand-by, press for a short period of time, start cleaning
In cleaning, press for a short period of time, pause cleaning
In recharging, press for a short period of time, stop recharging
7
Installation
Power on and charging
When using for the first time, please move the vacuum-mop to the
charging pole piece and align it with the charging shrapnel of the
self-cleaning station to charge.
In daily use, directly press the “ ” button to start intelligent
recharging.
Note:
Clean the dust compartment regularly to avoid the dirt affecting the cleaning effect.
Sweeping mode (Install dust compartment):
Cover opening
Recharging cleaning button:
In in-station stand-by, press for a short period of time, start cleaning
In in-station cleaning, press for a short period of time, stop cleaning
Outside-station, press for a short period of time, recharge
In in-station stand-by, press for a long period of time, start air drying
In in-station air drying, press for a long period of time, stop air drying
Install accessories based on the demanded
cleaning mode:
Open the face cover from the opening, put the dust compartment into
the vacuum-mop and make sure that the buckle is fastened securely.
8
Installation
Mopping mode (Installation of fresh water tank and mop):
Mop
Maximum water level
Hook & loop
Notes:
• In order to ensure the sterilization effect of brine electrolysis, please add
municipal tap water into the fresh water tank and do not use purified water.
• Do not inject hot water into the fresh water tank to avoid deformation of the
fresh water tank.
• When mopping the floor, please set up virtual walls or forbidden zones in
the carpet area.
• It is forbidden to use cleaning products such as detergent, disinfectant and
solid detergent to avoid corrosion and damage to the equipment.
• In case of water accumulation, please clean up the accumulated water
before using the function of cleaning or mopping.
• After mopping the floor, please take out and clean the dirty water tank in
time, and clean the cleaning brush, cleaning tray and dirty water filter to
avoid odor and mildew.
1. According to the figure, insert the mop along the slot of the
vibrating mop support and stick it on the hook & loop.
3. Install the fresh water tank and dirty water tank into the
self-cleaning station, and fasten the cover of the self-cleaning station
after completion.
2. Take out the fresh water tank and add municipal tap water
below the maximum water level.
Note
: Please check the dirty water tank regularly. If there is sewage, please
dump it in time to ensure that there is no water in the dirty water tank.
In the App, the vacuum-mop will automatically save the updated map
after quick mapping or completing cleaning and successful recharging.
After a map is completed successfully, you can split or merge zones or
name any room in the App.
Memory map
Vibration mopping mode is adopted by default when mopping the floor,
which can enhance mopping effect. The mode can be turned off in the
App.
Vibration mopping mode
In the App, a variety of cleaning modes and suction gears can be
selected.
Model/level selection
9
2. Configure the network
Connection with APP
1. Scan the QR code below or search for “Redroad” in the App store
to download and install the App.
Select and connect the device network according to the tips on the App page.
• Wi-Fi binding with Android mobile phone
• Wi-Fi binding with IOS mobile phone
Password
WiFi-2.4G
Enter the Wi-Fi setting page of the
mobile phone and select the
corresponding product hot spot until
the connection is successful; return to
the App interface, click “Next” to
complete the connection according to
the tips.
Note: Only Wi-Fi network in 2.4GHz band is supported.
Press and hold the “ + ” buttons for 7s to configure the network
Operation
3. Add the machine in the App interface and enter the Wi-Fi password
to connect
Press “ ” of the vacuum-mop for 3s, indicator light is on and the
vacuum-mop is on.
When the vacuum-mop is not charged and paused, press “ ” for 3s
to make it power-off.
Power-On/Off
In the power-on state, press the “ ” button for a short period of time,
and the vacuum-mop starts to work.
Cleaning
When the vacuum-mop is running, press the “ ” button of the
vacuum-mop for a short period of time to stop cleaning, and then press
the “ ” button for a short period of time again to continue cleaning.
Pause
Please fill the fresh water tank with fresh water before the sweeping
and mopping robot works.
Please pour out the water in the dirty water tank and clean it up after
the sweeping and mopping robot works.
Note: It is forbidden to use cleaning products such as detergent, disinfectant
and solid detergent to avoid corrosion and damage to the equipment.
Water adding or pouring in fresh water tank
This product has the function of breakpoint resume. During the cleaning
process, when the power is low, the vacuum-mop will automatically find
the cleaning station to charge, and after charging, it will return to the
breakpoint to continue cleaning. If the cleaning is manually finished or
the vacuum-mop is moved or operated during recharging or charging,
this breakpoint resume will be canceled.
Breakpoint resume
User can schedule a cleaning task in App, and vacuum-mop will start
the cleaning task as scheduled and return to cleaning station upon end
of the task.
Note: Any scheduled cleaning task will not be executed during the time
when non-disturbance mode is activated.
Scheduled cleaning
User can define virtual wall/ restricted area in App which main machine
will avoid cleaning.
Notes:
• Before using this function, you have to store a map in the App.
• Moving the main machine or change of indoor environment may
cause the original map lost and any virtual wall/ restricted area
unavailable.
Virtual Wall/ Restricted Area
10
In the process of sweeping and mopping, the vacuum-mop will
automatically return to the cleaning station to clean the mop midway;
after cleaning is completed, the vacuum-mop will automatically return to
the interruption point to continue sweeping and mopping;
In the process of sweeping and mopping, press the “ ” button of the
cleaning station for a short period of time, and the vacuum-mop will
return to the cleaning station and clean the mop;
After sweeping and mopping, the vacuum-mop will automatically return
to the cleaning station to clean the mop; after cleaning, enter the
stand-by state;
In the process of sweeping and mopping, press the “ ” button of the
vacuum-mop for a short period of time, and the vacuum-mop will start
recharging and automatically clean the mop, and then enter the
stand-by state after cleaning;
In stand-by state in the self-cleaning station, press the “ ” button of
the self-cleaning station for a short period of time to clean the mop.
After cleaning, it will enter the stand-by state.
Mop cleaning
Operation
When the vacuum-mop completes cleaning, it will automatically
recharge, and determine whether to clean the mop according to the
cleaning mode;
The vacuum-mop is outside of the station, press the “ ” button of the
vacuum-mop for a short period of time to start recharging. After
recharging successfully, judge whether to clean the mop according to
the cleaning mode.
Equipment recharge
Other manuals for G10
2
Table of contents
Other Redroad Vacuum Cleaner manuals
