Quantum PX502 Reference manual
Document 81-81453-02 A01, January 2006 1
Quantum PX502
Chassis Repacking Instructions
Introduction 3
Removing the Library from the Rack 3
Installing the Internal Shipping Restraints 6
Packing the Library for Shipment 12
Quantum PX502 Chassis Repacking Instructions
Document 81-81453-02 A01
January 2006
Made in the USA.
Quantum Corporation provides this publication “as is” without warranty of any kind, either express or implied, including but not
limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation may revise this publication
from time to time without notice.
COPYRIGHT STATEMENT
© Copyright 2003 by Quantum Corporation. All rights reserved.
Your right to copy this document is limited by copyright law. Making copies or adaptations without prior written authorization of
Quantum Corporation is prohibited by law and constitutes a punishable violation of the law.
TRADEMARK STATEMENT
Sun StorEdge™ L25 Tape Library and Sun StorEdge™ L100 Tape Library are trademarks of Sun Microsystems, Inc.
Other trademarks may be mentioned herein which belong to other companies.
2
Quantum PX502 Chassis Repacking Instructions
Document 81-81453-02 A01
January 2006
Introduction 3
Introduction 0
This document explains how to repack the Quantum PX502 library. Follow
these instructions carefully to ensure the library is shipped properly.
Note: All PX500 Series documentation is located on the PX500 Series
Documentation CD included in the library accessory kit.
Caution: This procedure requires the packing materials originally sent
with the library for proper shipment. If you do not have the
library packing materials, contact Quantum customer support
for replacement packaging (800) 284-5101.
This procedure consists of the following steps:
•Removing the Library from the Rack
•Installing the Internal Shipping Restraints
•Packing the Library for Shipment
Removing the Library from the Rack 0
To remove the PX502 library from the rack:
Note: You must remove all tape cartridges from the library prior to
parking the library robotics for shipment.
1Using the OCP, open the front doors, remove both tape cartridge
magazines, and remove any tape cartridges from the fixed bins or
FlexLink™ (refer to the Quantum PX500 Series User’s Guide PN 81-81290
for information on OCP operation and bin locations).
After removing the tape cartridge magazines and closing the doors, the
library inventories all possible tape cartridge locations (magazines, fixed
slots, Flexlink, and tape drives). This process takes several minutes.
2From the Library Operations screen on the OCP, select Park for Shipping.
The library shuts down automatically.
Note: If there are tape cartridges in the library, the system will NOT
park the library robotics. You must remove all tape cartridges
from the system prior to parking the library robotics.
Quantum PX502 Chassis Repacking Instructions
Document 81-81453-02 A01
January 2006
4 Removing the Library from the Rack
3From the back of the library, disconnect all power, Ethernet, and SCSI
cables from the library and note their locations for later reinstallation.
Warning: This unit has more than one power supply cord.
Disconnect all power supply cords before servicing to
avoid electric shock.
4To remove the library chassis from the rack (see figure 1):
Note: Refer to the PX502 Quick Start Guide (PN 81-81292) for
additional PX502 rack mount information.
aLoosen the captive screws securing the tape drives to the chassis and
remove the tape drive(s) from the back of the library.
bLoosen the captive screw securing the power supplies to the chassis
and remove the power supplies from the back of the library.
cRemove PHILLIPS® screws securing each side of the chassis to the
rack mounting rails and remove two Allen screws securing both
clamps on the back of the library.
dRemove the library from the rack.
Warning: At least two people are required to move the library
chassis.
Quantum PX502 Chassis Repacking Instructions
Document 81-81453-02 A01
January 2006
Removing the Library from the Rack 5
Figure 1 Removing the
PX502 Library
Power supplies
Tape drives
Right magazine
Quantum PX502 Chassis Repacking Instructions
Document 81-81453-02 A01
January 2006
6 Installing the Internal Shipping Restraints
Installing the Internal Shipping Restraints 0
To ensure that the internal robotics within the library is not damaged, you
must install the internal shipping restraints on the robotics.
Caution: Failure to install the shipping restraints on the robotics may
void your warranty.
To install the internal shipping restraints:
1Place the library on a flat surface and remove the twelve PHILLIPS screws
securing the FlexLink™ cover and top cover plate to the library chassis
(see figure 2):
Note: If the bottom FlexLink cover has been removed, replace it
before shipping the library back to Quantum.
Figure 2 Removing the
Top Cover
Top cover
FlexLink cover
Quantum PX502 Chassis Repacking Instructions
Document 81-81453-02 A01
January 2006
Installing the Internal Shipping Restraints 7
2If the library is not operational and the Park for Shipping command was
not executed, grasp the robotics and gently move it to the front of the
library (see figure 3).
Caution: Take standard ESD precautions when working within the
library chassis.
Note: If there are any cartridges in the fixed bins, you can remove
them now.
Figure 3 Moving the
Robotics
Library robotics
Front
Back
3Install the metal restraints through the chassis eyelets as shown in
figure 4.
Quantum PX502 Chassis Repacking Instructions
Document 81-81453-02 A01
January 2006
8 Installing the Internal Shipping Restraints
Figure 4 Installing the
Metal Restraints
Metal restraints
Eyelet
4Install the two halves of the robotics shipping foams as shown in figure 5:
aInstall the left-hand foam first so that it fits down into the robotics
platform, then push towards the back of the unit until it stops.
bInstall the right-hand foam onto the library robotics so the motor fits
into the foam opening, then push towards the front of the library until
it stops.
Quantum PX502 Chassis Repacking Instructions
Document 81-81453-02 A01
January 2006
Installing the Internal Shipping Restraints 9
Figure 5 Installing the
Robotics Restraints
Robotics assembly shown
outside of library for clarity.
Right-handshipping
foam
Robotics motor
Left-hand shipping
foam
Foam inside
robotics platform
5Slide the robotics with the shipping foams under the metal restraints so
the metal bands fall into the restraint cutouts. Clamp the two halves of
the metal restraints together and secure with a tie band to secure the
robotics to the library chassis (see figure 6).
Quantum PX502 Chassis Repacking Instructions
Document 81-81453-02 A01
January 2006
10 Installing the Internal Shipping Restraints
Figure 6 Securing the
Robotics
Tie band
6Install the top covers previously removed in step 1.
7Install the tape drives, and power supplies previously removed in
Removing the Library from the Rack.
8To install the tape magazines, insert the metal pick included with the
accessory kit into the release holes and trip the magazine door release for
both the right and left magazine doors (see figure 7).
The magazine access doors open.
Other manuals for PX502
1
Table of contents
Other Quantum Storage manuals
Quantum
Quantum DXi6900-S User manual
Quantum
Quantum SNC 4500 User manual
Quantum
Quantum Tape Drive A-Series User manual
Quantum
Quantum P4000 Series Installation and operating instructions
Quantum
Quantum ACL 4/52 Manual
Quantum
Quantum DX100 Parts list manual
Quantum
Quantum LTO 3 User manual
Quantum
Quantum PX720 User manual
Quantum
Quantum DXi6701 Technical manual
Quantum
Quantum Q2000 User manual
Quantum
Quantum StorNext AEL500 User manual
Quantum
Quantum DXi7500 Technical manual
Quantum
Quantum Scalar i2000 User manual
Quantum
Quantum DLTtape SDLT 600 User manual
Quantum
Quantum F2000 User manual
Quantum
Quantum SNC 4000 User manual
Quantum
Quantum Scalar i6000 User manual
Quantum
Quantum Scalar 50 User manual
Quantum
Quantum DLTtape SDLT 220 User manual
Quantum
Quantum PX500 Series Quick start guide
