Prorack K657 User manual
K657
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 4 x 4 x 8 x 2
x 2 x 4 x 4 x 2
x 2 x 2 x 2
Revision No: 1A 1
Fitting Kit K657
MAX kgs (lbs)
W/P WHD
Hyundai
Santa Fe , 5dr SUV 12-+ ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
Santa Fe , 5dr SUV 12-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Santa Fe , 5dr SUV 12-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Santa Fe Sport, 5dr SUV 13-+ US 75 kgs (165 lbs) 75 kgs (165 lbs)
Santa Fe , 5dr SUV Aug 12-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
2
Fitting Kit EN
K657
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
3
Fitting Kit EN
K657
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment.
●Ensure each end of the crossbar is
adjusted equally.
●Set bars to length (refer to the crossbar
instructions for crossbar adjustment).
●Clamps onto flush roof rail. Pins locate on
inside of rail.
4
Fitting Kit EN
K657
●Tighten adjusting screw to 5 Nm (3.7 ft lb).
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Remove both pins from each leg. Use
tapered end of spanner located inside left
hand cover to assist.
5
Fitting Kit EN
K657
●Detach foot from leg. Store loose parts in a
safe place.
●Repeat for all legs.
●Select four feet assemblies and match the
left and right assemblies to the left and
right roof rack legs.
●Assemble foot from kit into leg by pressing
it down.
●Ensure foot interlocks with leg.
●Using short capscrew and washer, secure
assembly onto leg (use Hex Screwdriver
supplied with crossbar to assist)
●Do not over tighten.
●Repeat for all legs.
6
Fitting Kit EN
K657
●Use two M5 x 12 mm self tapping screws to
secure the assembly onto the leg.
●Do not over tighten.
●Apply protective strip as shown.
Trim if required.
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 915A
B = 929A
7
Fitting Kit EN
K657
Fitment
●Locate three holes at each position along
the inside of the roof rails.
●Place crossbars approximately above
these holes on roof rails.
●Ensure back edge of foot sits flush with the
back edge of vehicle roof rail.
●Place one hand on the leg and apply
downward pressure.
●Slide clamp through opening in leg.
8
Fitting Kit EN
K657
●Ensure the pins of the clamps engage
correctly with the holes in the roof rail.
●Thread the coach bolt through the clamp
and the leg.
●Tighten the red plastic knob.
●Ensure the red plastic knob is in the
position shown when fully tightened.
●Do not over tighten.
●Repeat for all four positions.
●Ensure the clamp engages correctly on
inside of roof rail.
●Use keys to fit and lock covers
●Check crossbar is securely attached to the
vehicle.
9
Fitting Kit EN
K657
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack WHISPBAR S53 Operation and installation manual
Prorack
Prorack K639 User manual
Prorack
Prorack K723 User manual
Prorack
Prorack Whispbar S42 User manual
Prorack
Prorack K470 User manual
Prorack
Prorack K446W Operation and installation manual
Prorack
Prorack K802 User manual
Prorack
Prorack K843 User manual
Prorack
Prorack K692 User manual
Prorack
Prorack K188 User manual
Prorack
Prorack K175 User manual
Prorack
Prorack K536 User manual
Prorack
Prorack K082 User manual
Prorack
Prorack K417 User manual
Prorack
Prorack K100 User manual
Prorack
Prorack K568 User manual
Prorack
Prorack K607 User manual
Prorack
Prorack K577 Operation and installation manual
Prorack
Prorack K814 User manual
Prorack
Prorack K311 User manual
