PROAIM P-W5P24-BASE User manual

What’s In The Box

Please inspect the contents of your shipped package to ensure you have received everything that

is listed below.

No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,

electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright

statutes or in wring by the Publisher.

24 Camera Crane Base Kit (P-W5P24-BASE)

Assem b l y M a n u a l

Packaging Material of Box-1

 D-37 Dolly

 Dolly plaorm

Packaging Material of Box-2

 Tripod Stand

Packaging Material of Box-3

 Head Plaorm

 1st Jib Secon - 6th Secon

Packaging Material of Box-4

 14.5 Cable

 2x 13.5 Cables

 7.9 Cable

 6.9 Cable

 6.7 Cable

 3x 3.7 Cables

 3.1 Cable

 2.4 Cable

 2.2 Cable

 Safety Chain

 Cable Guide

 Supporng Rod

 Central Fork

 Wire Tensioners

 Hooks

 Screws

 Weigh Bar with Closers

Please use following sequence of pictures and text in order they appear to set up your new PROAIM

24FT BASE KIT. Technical assistance is available by contacng our sales representave.

14.5

Cable 13.5 Cables 7.9

Cable

6.9

Cable 6.7

Cable

3.7 Cables 3.1 Cable

Safety Chain Cable

Guide

Supporng

Rod

Screws

Central Fork

Weight Bar

with Closers

Hooks

Wire

Tensioners

2.4

Cable

2.2

Cable

Safety Hints

ATTENTION: PLEASE READ THIS BEFORE USING TO PREVENT DAMAGE TO EQUIPMENT

& OPERATOR!

 The crane may not be assembled or operated under the inuence of alcohol, drugs or any other

intoxicang substances. Lack of aenon while connecng the components can cause substanal

damage to equipment/operator.

 The crane may only be operated on levelled horizontal posion. Make sure that the surface is stable.

 Make sure the dolly and stand are correctly installed before the crane setup is put on.

Dolly & Tripod Stand Setup

 You will receive your D-37 dolly collapsed for shipping/storage purposes. To extend the legs, take out

the Allen bolts from both outer legs & pull out each leg unl it reaches to joining connecons and secure

with the bolts as shown below.

 To prevent any harm or injury, properly join all secons of the crane. It is suggested to use the support

stand while telescoping the complete length.

 Test operaon before usage. Neglect of such a step can cause harm to equipment or operator.

 Always connect the steel cables properly to provide stability to the system. They should not negavely

impact the movements of the crane in any way.

 Aer setup of the crane, the pan-lt head / gimbal head shall be posioned under the central pivot

secon. In the assembled state, when the pan-lt head / gimbal head is higher than the central pivot

secon, there should be someone to look aer the crane system.

 The complete panning & liing range around it must be kept free. Avoid anybody standing under the

crane. No loose objects may be stored or placed on it. Be very careful while using it indoors.

 Never operate the crane near high-voltage power cables. It holds danger to life.

 Parcular care is required when operang the crane in unfavourable weather condions. The crane

must be shut down in sucient me. When it is used on a rainy day, the pan-lt head / gimbal head and

controlling bar shall be protected against rain.

 When you want to transport the crane, make sure that the components do not rub together and cause

any material wear.

 Before the counterweights are removed, ensure the remote head is resng on the support stand. Then

gradually remove the counterweights before the remote head, camera or other parts.

 In the interest of safe crane operaon, avoid abruptly swivelling or stopping the crane; otherwise, it may

cause severe damage to equipment.

FOLLOWING THESE GUIDELINES WILL PROVIDE BETTER SHOTS AND TROUBLE-FREE OPERATION.

SHOULD YOU NEED ADDITIONAL INFORMATION, TECHNICAL ASSISTANCE IS AVAILABLE ‘ONLINE’ BY

CONTACTING THE SALES REPRESENTATIVE.

 Set the posion of wheels and lock wheels with

provided lever which allows you to have stable shoots.

 Aach dolly plaorm to D-37, screw in the Allen bolts to desired posions and ghten all connecons

with the help of Allen key.

 Aach the legs of tripod stand with D-37 dolly as shown

in the image.

 Detach Locking clamp from central fork, mount central fork to tripod bowl, again aach Locking clamp

for secure connecon.

Locking clamp

 To add stability to your Jib, aach wire tensioner with hook on Locking clamp, then aach one end of

safety chain with hook on D-37 dolly and aach other end with wire tensioner as shown below.

Jib Secons Setup

 Wire tensioner and safety chain setup should be

properly aligned to ensure stability.

 Install the 5th Secon to the rear of vercal pivot point through bolt, washers and nut. Tighten the nut

properly to secure the secon.

 Slide in 6th secon to the rear to join the 5th secon. Install the Allen screws to the joining holes of

both the secons and ghten.

 Using the same approach insert 4th, 3rd and remaining secons to the joints and secure via bolts as

shown below.

Cable Guide & Rod Support Setup

 Aach cable guide to cable guide clamp on 5th secon properly. Loosen the bolts on cable guide clamp

in order to aach cable guide support rod to it. Reghten the bolt.

 Aach hooks to provided hook slots on all secons of the jib as shown below.

Cable guide

Support rod

 Then aach 3 hooks to the hook that you aached (as per above image) with 1st secon & 1 hook to

3rd secon.

 Aach 3 hooks one aer another to four wire tensioners.

 Aach 2 hooks on both slots on cable guide. Then aach two extra hooks to hook aach to front side

and two hooks to hook aached on back side.

 Now aach one end of 2.2 cable with Red Sleeves to hook on back side of cable guide and another

end to hook on 1st slot on jib secon with the help of wire tensioner.

Cables Setup

 Aach 3.1 cable with Red Sleeves to same hook on cable guide and another end with hook on 2nd

slot of rear secon as shown below.

 Now join 3.7 cable & 6.7 Cable with Red Sleeves.

 Aach the end of 6.7 cable to one of the hook aached on front side of cable guide and another end

of 3.7 cable with hook aached to 3rd secon of jib.

 Aach 14.5 cable with Red Sleeves to hook aached on 1st secon of jib and another end with 2nd

hook aached to cable guide as shown below.

 Now join 3.7 cable & 13.5 cable with Blue sleeves.

 Then aach the end of 13.5 cable to wire tensioner with hooks aached to 6th secon and another

end of 3.7 cable with 2nd hook aached on 1st secon.

 Using the same approach aach cable to wire tensioner on another side of jib and one end with 3rd

hook on 1st secon.

 Now pass both side cables through space on boom of cable guide support rod as shown below.

 Install Head Plaorm assembly (leveling arm up) to the end of the smallest secon with the provided

bolt, sha collars, washers and nut. Tighten all the Allen bolts and nuts to secure properly.

NOTE: Install the pan lts head.

 Now Join 2.4 cable, 6.9 cable & 7.9 cable with yellow sleeves.

 Aach one end of cable to slot on head plaorm with the help of wire tensioner and another end with

the cable already aached to central fork with wire tensioner as shown below.

Head Plaorm Setup

Cable aached to

central fork

 Loosen the knob on rear secon, remove closers from weight bar and insert it to slot on rear secon.

Reghten the knob to ensure slip free connecon.

 Aach weights (Not supplied) to both ends of weight bar, secure with the help of closers.

 Aach LCD mount L-bracket to bracket already aached to rear secon with knob.

 Now mount LCD (not included) to L-bracket and ghten with screw driver.

YOUR PROAIM 24 CAMERA CRANE BASE KIT

ALL DRESSED UP AND READY TO GO

(SHOWN WITH OPTIONAL ACCESSORIES)

Other manuals for P-W5P24-BASE

Table of contents

Other PROAIM Camera Accessories manuals

PROAIM

PROAIM CAMTREE HUNT User manual

PROAIM

PROAIM P-OHBP-01 User manual

PROAIM

PROAIM E-FOCUS PRO ZOOM Manual instruction

PROAIM

PROAIM RN-244-00 User manual

PROAIM

PROAIM CH-FS7-TBK User manual

PROAIM

PROAIM VCTR-CP User manual

PROAIM

PROAIM P-MWP-D User manual

PROAIM

PROAIM P-12-JS User manual

PROAIM

PROAIM CINEMA Series User manual

PROAIM

PROAIM P-18-JS User manual

PROAIM

PROAIM CINEMA Series User manual

PROAIM

PROAIM LV-3WAY-01 User manual

PROAIM

PROAIM CINEMA Series User manual

PROAIM

PROAIM Follow Focus X1 User manual

PROAIM

PROAIM Quad Bazooka User manual

PROAIM

PROAIM CINEMA Series User manual

PROAIM

PROAIM CINEMA Series User manual

PROAIM

PROAIM CINEMA Series User manual

PROAIM

PROAIM CINEMA Series User manual

PROAIM

PROAIM Astra User manual

PROAIM

PROAIM QR-ELMG-01 User manual

PROAIM

PROAIM RS274 User manual

PROAIM

PROAIM Cinema Series Comet User manual

PROAIM

PROAIM JB-FR6T-00 User manual

Popular Camera Accessories manuals by other brands

Viltrox

Viltrox EF-NEX Mount instructions

Calumet

Calumet 7100 Series CK7114 operating instructions

Ropox

Ropox 4Single Series User manual and installation instructions

Cambo

Cambo Wide DS Digital Series Main operating instructions

Samsung

Samsung SHG-120 Specification sheet

Ryobi

Ryobi BPL-1820 Owner's operating manual

Aegis

Aegis ABL-36020P user manual

Pentax

Pentax Data Back Fc operating manual

Fantasea

Fantasea EyeGrabber F Series instruction manual

Honeywell

Honeywell HDZ20HD user manual

EGO

EGO BA1400T Operator's manual

Sima

Sima SRW-62 user guide

Shape

Shape A7SSMKIT Assembly manual

Slide Kamera

Slide Kamera HST-2 user manual

Power works

Power works 2902613 Original instructions

SES

SES SE-2047-2 user manual

Olympus

Olympus PT-EP05L instruction manual

Starlite

Starlite OctoDome nxt instructions