Premier Mounts AM100 User manual
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
1321 S. State College Blvd., Fullerton, CA 92831 USA
Installation Guide
AM100
Low-Prole Ultra-Slim Swingout Mount for Flat-Panels
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Included Components
Required for installation
AM100
Installation Guide
Maximum Flat Panel Weight:
100 lb. / 45.5 kg.
5/16” x 3” Lag Bolts
(Qty 4)
Green Level
(Qty 1)
Universal Spacers
(Qty 8)
5/16” Flat Washers
(Qty 4)
Universal Washers
(Qty 4)
Depth Measuring Straw
(Qty 1)
10mm Socket
(Qty 1)
M4 Allen Key
(Qty 1)
M2.5 Allen Key
(Qty 1)
Finned Anchor
(Qty 4)
Pencil Protective Eyewear
Electronic Stud Finder M6 or 1/4” Wood Drill Bit 3/8” Concrete Drill Bit
Portable Drill Hammer
Phillips Head ScrewdriverLeveler Socket Wrench
13mm or 1/2” Socket
M6 x 16mm (Qty 4)
M6 x 25mm (Qty 4)
M8 x 16mm (Qty 4)
M8 x 25mm (Qty 4)
Wall Mount
(Qty 1)
Template
(Qty 1)
Page 2
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Installation Guide
AM100
A1
A2
Prior to initial step 1 of the installation, your AM100 can easily
have the main “swing left” pivot point of the main swing out
arm moved to either the center, left or right of the mount by
simply placing the mount on a flat surface and removing the
eight flat head screws, then separating the upper and lower
wall plates.
Pivot
Set Screw
Locations
Set Screw
Locations
Remove the plastic hole covers from the upper and lower
plates. Loosen the (2) set screws on the plate using the
2.5mm allen key supplied. Reposition the upper and lower
pivot rods to mate to either the center or right side pivot
receiver holes, push the upper and lower plate fully on to the
rods, and re-tighten the set screws. Reinstall the side plate
with the eight flat head screws and confirm they are secure.
Reinstall the round plastic hole covers.
M2.5 Allen Key
Page 3
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Installation Guide
AM100
1
2
Using a suitable stud-finder device for frame walls, mark the
position of the stud centers.
Measure the desired height of the center of the screen and
mark it.
Take the thick cardboard mounting template supplied and
place the it over the mounting studs with the screen center
facing up. Confirm that the template is level horizontally and
that the wall place outline is to the center of your desired
height.
Page 4
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Installation Guide
AM100
3
4
Using a 1/4” drill bit, drill pilot holes minimum 2” (50mm)
deep into the four marked mounting points on the wall
surface. For solid concrete wall construction, the supplied
plastic wedge anchors are recommend to be used with the
5/16 x 3” lag bolt and washers supplied.
To ease the installation process you have the option to
remove the wide front plate and mounting brackets by simply
removing the three M5 x 10mm flat head screws, holding
the plate assembly to the swing out arm assembly and set-
ting them aside.
1/4” / M6
Wood Only
Page 5
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Installation Guide
AM100
5
6
Raise the AM100 assembly so the mounting slots are
over the four drilled mounting holes. Confirm mount
level with spirit level and secure the mount to the wall
surface with the four each 5/16 x 3” lag bolt and 5/16”
flat washer supplied.
Level the wall mount in the following order on figure 5
and below
Re-confirm secured assembly is level horizontally and
vertically or level again if necessary before proceeding.
NOTE: Do not over tighten lag bolts
1. Level the wall mount in following order on figure 6
and below.
2. Mark the pointing points.
3. Drill the concrete wall using a 3/8” concrete drill bit.
4. Lighty hammer the four (4) Finned Anchors into the wall.
5. Tighten the (4) 5/16” washers and (4) 5/16” x 3” lag bolts into
the wall.
Wood Stud
Concrete Wall
Leveler
Leveler
1/2”
1/2”
x4
x4
x4
x4x4
Page 6
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Installation Guide
AM100
8
7Re-install the front wall arm plate to the arm with the three
M5 flat head screws you set aside earlier. Confirm screws
are fully seated and tight.
Take the plastic depth straw supplied and confirm the overall
“safe” screw depth that can be used.
Page 7
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Installation Guide
AM100
10A
Once the correct pitch and depth screws are pulled from
the hardware pack supplied, secure the two brackets to the
rear of the display with the proper screws and plate washer
holes. Plastic spacers are also supplied in case you need
additional clearance between the bracket and the rear of the
display. NOTE: Do not over tighten the screws.
9Place the display face down on a smooth flat surface. Place
the left and right mounting brackets over the four mounting
points on the rear of the display arrow pointing up to the top
of the display, making sure the brackets are lined up with the
center top to bottom on the display.
x4
x4
x4
x4
Page 8
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Installation Guide
AM100
11
10B With the upper and lower security screws loosened on each
bracket (two people recommended) raise the display and
place the top hook of the bracket over the receiver plate on
the wall mount. Allow the lower end of the bracket to lay flat
against the mating plate on the mount.
Center the display horizontally on the plate and check the
display is level on the mount. To adjust level, adjust the left
or right top screw to achieve desired level of the display.
Once level, secure the lower left and right security screws
on the bracket to “fix” the mount to the wall mount.
Page 9
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Installation Guide
AM100
13 We recommend where possible that the power and signal
cables be run separately through the mount until mating at
the display plug in points to minimize possible “cross talk”
interference. With the covers removed, cable can be run
inside the upper and lower main arm and through the slots
behind the plastic beauty covers.
12 Tilting of the display on the mount is easily accomplished by
placing one hand on top of the display edge center and one
hand on the bottom of the display edge center and gently
pulling out on the top edge to the desired tilt angle. No lock-
ing of the set tilt angle is required as the mount has built-in
friction control. If additional tension is required, use the
socket and M4 allen key to adjust the desired tension.
Extra tension can be applied to the pivot of the arms by
tightening the nuts on the arm with supplied 10mm deep
socket, and the set screws on the base with the supplied
2.5mm allen key. NOTE: Do not over tighten.
10mm Deep Socket
M2.5 Allen key
M2.5 Allen key
Page 10
Other manuals for AM100
2
Table of contents
Other Premier Mounts Rack & Stand manuals
Premier Mounts
Premier Mounts Elliptical Floor Cart and Stand PSD-EB72C User manual
Premier Mounts
Premier Mounts PTM User manual
Premier Mounts
Premier Mounts GB-AVSTOR4 User manual
Premier Mounts
Premier Mounts Rotary RTM-S User manual
Premier Mounts
Premier Mounts PDS-PLUS User manual
Premier Mounts
Premier Mounts PSD-TS User manual
Premier Mounts
Premier Mounts EST100 User manual
Premier Mounts
Premier Mounts LMVSP User manual
Premier Mounts
Premier Mounts Multi-Monitor with table adapter MMT User manual
Premier Mounts
Premier Mounts AM300-B User manual
Premier Mounts
Premier Mounts MM-CB3 User manual
Premier Mounts
Premier Mounts USA User manual
Premier Mounts
Premier Mounts PTM-B User manual
Premier Mounts
Premier Mounts AM225 User manual
Premier Mounts
Premier Mounts CONVERGENT SAM-IFJ Series User manual
Premier Mounts
Premier Mounts PSD-TTS/B User manual
Premier Mounts
Premier Mounts Convergent A-A27 Series User manual
Premier Mounts
Premier Mounts CTM-MS1 User manual
Premier Mounts
Premier Mounts UNI User manual
Premier Mounts
Premier Mounts UMB-DBTS User manual
Popular Rack & Stand manuals by other brands
Salamander
Salamander Acadia AC/W/L400/WH Assembly instructions
Fohhn
Fohhn VAT-09 Mounting instruction
ricoo
ricoo FS0522 quick start guide
AMSOIL
AMSOIL BMK-22 Installation and service instructions
Kargo Master
Kargo Master 48220 installation guide
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 installation instructions
