Precor Resolute RSL 515 User manual

ENGLISH

Resolute™ Strength Selectorized Line

Converging Shoulder Press RSL 515

Assembly Guide

Assembly Requirements

It takes about 90 minutes to assemble this equipment. If this is your rst time doing this, allow more time.

CAUTION

At least two people are required to assemble the equipment. DO NOT attempt to assemble this by yourself. Precor recommends that all strength equipment be bolted to the

ooring at all anchoring points.

Installation Requirements

● Unpack the boxes and assemble the equipment close to where you plan to use it.

● Locate equipment at least 40 inches (1 meter) away from any walls, furniture, or objects on all sides.

● While tightening the fasteners, be sure to leave room for adjustments. DO NOT fully tighten fasteners until instructed to do so.

● Set up and assemble the equipment on a solid, at surface, so that it remains level and stable.

● DO NOT move the equipment without assistance.

Required Tools

● Torque wrench with torque range to at least 150 ft-lb (206 N-m) and ts the following hex bits: 6, 8, and 10 mm

● Socket wrench sets, metric and standard, plus extensions

● Open-end wrench sets, metric and standard

● Hex wrench sets, metric and standard, plus extensions

●Box cutter

●Rubber mallet

● Retaining ring pliers - large, medium, and small

● Pliers - large, medium, and small

Trademarks

Resolute is a trademark and Precor is a registered trademark of Precor, Incorporated.

All other trademarks belong to their respective owners.

Part # Name Quantity Part # Name Quantity

Main frame 1 Seat pad 1

Arm, left 1 Back pad 1

Arm, right 1 Weight plates 10 lb (4.5 kg) 19

Seat assembly 1 Weight labels 1

Lower cross brace 1 Collars 2

Upper cross brace 1 End plugs with sleeves 2

Bumpers 4 Roller adjustment tool (attached to Seat assembly) 1

Shaft 1 Washers, 12.2 mm ID x 35 mm OD 2

Roller assembly 1 Washers, rubber, black 3

Gas spring 1 Washers, domed, silver 2

Weight stack tower frame 1Washer, silver 13.5 mm ID x 35 mm OD 1

Top plate assembly 1Washers, 9 mm 6

Add-on weight spacer, 2½-inch 1 Hole plugs 2

Add-on weight 5 lb (2.2 kg) 1Retaining rings, 3/4-inch 2

Add-on weight handle 1Socket head cap screws (SHCS) M12 x 25 mm 2

Kick plate 1 Socket head cap screws (SHCS) M12 x 35 mm 6

Weight stack spacer, 3-inch 1Socket head cap screws (SHCS) M12 x 130 mm 2

Guide rods 2 Socket head cap screws (SHCS) M10 x 65 mm 2

Shroud, crown 1Socket head cap screws (SHCS) M10 x 40 mm 2

Guide rod with cap 1Button head cap screws (BHCS) M10 x 125 mm 2

Shroud, rear upper 1Button head cap screws (BHCS) M6 x 15 mm 2

Shroud, front upper placard 1Hex head screws 5/16-inch x 1½-inch 6

Shroud, rear lower 1Nylon lock nuts, M12 2

Shroud, front lower 1Nylon lock nuts, M10 2

Shroud, rear middle 1Washers, 13 mm 8

Shroud, front middle (left and right) 2 Washers, 11 mm 5

Top tray 1

Shroud, lower pulley cover 1

Parts List

Frame Assembly

DO NOT tighten fasteners until instructed to do so.

Have your assistant hold frame parts in place during assembly.

Image Hardware Instructions

12 M12 x 130 mm SHCS

4 washers, 13 mm

2 M12 nylon lock nuts

Tools: Hex wrench, 10 mm

Socket wrench, 19 mm

2 M10 x 125 mm BHCS

1 washer, 11 mm

Connect lower cross brace to weight stack tower and

kick plate .

Align to second hole from right.

Insert guide rod fasteners, one from each side, to align kick

plate. Hand tighten only. These will be removed temporari-

ly in a later step.

2 2 M12 x 35mm SHCS

2 washers, 13 mm

Tool: Hex wrench, 10 mm

Connect lower cross brace to main frame .

32 M12 x 35 mm SHCS

2 washers, domed, silver

Tool: Hex wrench, 10 mm

Connect upper cross brace to weight stack tower .

42 M12 x 35 mm SHCS

2 washers, 13 mm

Tool: Hex wrench, 10 mm

Connect upper cross brace to main frame .

5Tools: Hex wrench, 10 mm

Socket wrench, 19 mm

Torque wrench

Gently rock the frame to align. Tighten all M12 fasteners to

55 ft-lb (75 N-m) of torque.

Do not tighten the M10 screws installed in step 1 at this

time. They will be removed temporarily in a later step.

Moving Parts

Image Hardware Instructions

12 collars Slide collars onto arm shafts on main frame. Ensure at sides of

collars are towards main frame.

2Slide left arm and right arm onto shafts at top of main

frame . Each arm has and labels. Match the arm labels

with the labels at the top of the main frame to ensure proper

placement.

32 washers, rubber

2 washers, 12.2 mm ID x 35 mm OD

2 M12 x 25 mm SHCS

Tool: Hex wrench, 10 mm

Slide washers on to each arm in order shown. Hold washers cen-

tered and secure.

42 end plugs with sleeves

Tool: Mallet

Slide end plugs with sleeves onto ends of arms. Tap gently with

mallet if needed.

Remove all and labels.

Seat Assembly

Image Hardware Instructions

1 1 roller assembly

1 shaft

2 retaining rings, 3/4-inch

Tool: Pliers

Attach the seat assembly to the main frame . Place the roller assembly

between the seat assembly brackets and insert the shaft. Secure each side with

retaining rings.

21 gas spring Snap gas spring into place under seat and at base of main frame . The

larger body of the gas spring attaches to the seat.

3To adjust the roller clearance on the seat assembly , have your assistant apply

downward force on seat.

4Tools: Two hex wrenches, 8 mm Preinstalled on the front roller of the seat assembly is a roller adjustment tool .

Continue to apply force to the seat assembly and press the adjustment tool

downward to turn the roller. Turn until it just contacts the plastic ratchet plate

and no more than 180 degrees. Tighten the socket head screws on the sides of

the front roller (ensure the position of the roller tool does not change). Remove

tool.

54 hex head screws 5/16 x 1½-inch

4 washers, 9 mm

Tool: Socket wrench, ½-inch with extension

Attach seat pad to seat assembly .

Route the Cable

Image Hardware Instructions

1Tools: Two open end wrenches, 19 mm

Torque wrench

Ensure arms rest in frame. Attach cable to arms. Hold rod end and tighten nut.

Maximum distance is 25 mm.

Fully tighten to 50 ft-lb (67.7 N-m).

2 Tools: Hex wrench, 8 mm

Hex wrench, 4 mm

To route the cable around the lower pulley on the weight stack tower, remove

the cable retainer. Route the cable around the pulley and then replace the cable

retainer.

3Tools: Hex wrench, 8 mm

Open-end wrench, 19 mm

Torque wrench

To route the cable to the upper pulleys of weight stack tower, remove the cable

retainers, route the cables, and replace the retainers. Tighten to 50 ft-lb (67

N-m) of torque.

6 2 hex head screws 5/16 x 1½-inch

2 washers, 9 mm

2 hole plugs

Tool: Socket wrench, ½-inch with extension

Attach back pad to main frame .

30 41

Finish the Weight Stack Tower

Image Hardware Instructions

12 M10 x 125 mm BHCS

1 washer, 11 mm

Tool: Hex wrench, 6 mm

Remove the guide rod fasteners installed in step 1 of the Frame Assembly.

2 1 weight stack spacer, 3-inch

2 guide rods

Align the weight stack spacer over the holes on the base of the tower. Insert two

weight guide rods and lean outwards about 6 inches (15 cm), enough clearance

for the weights. Flat side of weight stack spacer should face user side.

32 bumpers

19 10 lb (4.5 kg) weight plates

1 top plate assembly

Slide one bumper on to each rod. Place the weight plates on the rods. Ensure the

side with three holes face the user side and single hole to the back. Place the top

plate over the weight plates. The plates and top plate should align ush on the

user side.

54 48

4Straighten the front two guide rods to a vertical position. Have your assistant lift

the guide rods up into the upper part of the frame.

5Tools: Hex wrench, 6 mm

Torque wrench

While the assistant is holding the rods into the upper frame, reinsert the two

bolts underneath the guide rods removed in step 1 above. Let the guide rods

drop onto the bolts and fully tighten the bolts. Tighten M10 screws to 32 ft-lb

(43 N-m) of torque.

6 1 M10 x 65 mm SHCS

2 washers, 11 mm

1 M10 nylon lock nut

Tools: Hex wrench, 8 mm

Socket wrench, 17 mm

1 guide rod with cap

Prepare the lower base for the add-on weight assembly. Place the retaining

screw through the bracket on the weight stack spacer.

Remove the cap from the guide rod and place the rod into bracket opening se-

cured by the screw.

7 2 bumpers

1 add-on weight spacer, 2½-inch

1 add-on weight

1 add-on weight handle

Place one bumper onto third guide rod, followed by the add-on weight spacer,

another bumper, the add-on weight, and the add-on weight handle.

46 52

54 48

Other manuals for Resolute RSL 515

Table of contents

Other Precor Elliptical Trainer manuals

Precor

Precor Resolute RSL 313 User manual

Precor

Precor Discovery Series User manual

Precor

Precor Experience Series 800 line EFX User manual

Precor

Precor Resolute RSL 515 User manual

Precor

Precor Commercial EFX EFX546 User manual

Precor

Precor EFX Series User manual

Precor

Precor EFX 556i Installation and operating instructions

Precor

Precor Elliptical Fitness Crosstrainer EFX 5.25 User manual

Precor

Precor Elliptical Fitness Crosstrainer EFX 5.25 User manual

Precor

Precor EFX5.21s User manual

Precor

Precor EFX 5.33 User manual

Precor

Precor EFX 835 Assembly Instructions

Precor

Precor EFX5.31 User manual

Precor

Precor Resolute RSL 504 User manual

Precor

Precor Experience Series User manual

Precor

Precor Resolute RSL 324 User manual

Precor

Precor EFX546 User manual

Precor

Precor Crosstrainer 800 User manual

Precor

Precor Resolute RSL 505 User manual

Precor

Precor EFX 825 User manual

Precor

Precor EFX 883 Assembly Instructions

Precor

Precor Resolute RSL 605 User manual

Precor

Precor C532i User manual

Precor

Precor AMT Series User manual

Popular Elliptical Trainer manuals by other brands

Weslo

Weslo Momentum 4.0 Elliptical Manuale d'istruzioni

Progear Fitness

Progear Fitness Air elliptical pro 1307 owner's manual

Torque Fitness

Torque Fitness XPLLP owner's manual

Octane Fitness

Octane Fitness PRO3700C Operation manual

Xterra

Xterra FS5.8e owner's manual

Bodyguard

Bodyguard E-40 user manual

Bonn Germany

Bonn Germany Concept 2.2 user manual

NordicTrack

NordicTrack E 9.2 Elliptical HASZNALATI UTASITAS

Vision Fitness

Vision Fitness X6600iNetTV Assembly guide

Matrix

Matrix MX-A5x owner's manual

SportsArt Fitness

SportsArt Fitness ECO-NATURAL Elite E874 owner's manual

Sears

Sears FREE SPIRIT C249 30737 0 owner's manual

True

True FS-64 Assembly manual

Sport-thieme

Sport-thieme ST 310 manual

VIRTUFIT

VIRTUFIT CTR 1.1 user manual

Kettler

Kettler GIRO C 1 manual

CIRCLE FITNESS

CIRCLE FITNESS E7 owner's manual

Reebok

Reebok 1000 Zx Elliptical Manuel de l'utilisateur