Precor EFX 5.33 User manual

5.33 Elliptical Fitness Crosstrainer

Page 1

5.33 Elliptical Fitness Crosstrainer

Warning: This service manual is for use by Precor trained service providers only.

IfyouarenotaPrecorTrainedServicer,youmustnotattempttoserviceanyPrecorProduct;

Call your dealer for service.

This document contains information required to perform the majority of troubleshooting, and

replacement procedures required to repair and maintain this product.

This document contains general product information, software diagnostic procedures (when

available), preventative maintenance procedures, inspection and adjustment procedures,

troubleshooting procedures, replacement procedures and electrical block and wiring diagrams.

To move directly to a procedure, click the appropriate procedure in the bookmark section to the

left of this page. You may “drag” the separator bar between this page and the bookmark section

to change the size of the page being viewed.

Unauthorized Reproduction and Distribution Prohibited By Law

20039-126

5.33 Ellipitical Fitness Crosstrainer

Page 2

Section One - Things You Should Know

Right, Left, Front, and Back Conventions

In this manual, right, left, front, and back are from the perspective of a user standing on the EFX

5.33, facing the display enclosure. Three versions of 5.33 have been manufactured. Version 1

(serial code CR) and version 2 (serial code ST) are essentially the same except that version two

has the capability of remote software upload. Version 3 (serial code AAAB) incorporates changes

in the product color scheme (stone gray), the eddy current magnet mounting, lower PCA

mounting and speed sensor mounting.

Warning and Caution Statements and General Safety Guidelines

Warning statements indicate a particularly dangerous activity. Warning statements you will find in

this manual include:

• To remove power from the EFX 5.33, the power cord must be disconnected from the wall

outlet. Always ensure that the EFX 5.33 is unplugged from the wall outlet when you inspect

or adjust the EFX 5.33, or when you isolate, remove, or replace a EFX 5.33 component.

• Removing the covers exposes high voltage components and potentially dangerous

machinery. Exercise extreme caution when you perform maintenance procedures with the

hood removed.

• During service operations you will be very close to moving machinery and high voltage

components. When you perform maintenance procedures with the covers removed, remove

jewelry (especially from ears and neck), tie up long hair, remove neck ties, and do not wear

loose clothing.

• Hazardous pinch points exist between the ramp and moving arm linkage.

• Exercise caution when touching any wire or electrical component during EFX 5.33

operation.

Caution statements are intended to prevent damage to the EFX 5.33 as a result of the current

activity. Caution statements included in this manual are listed below:

• Notice the orientation notch on the PROM. These components must be positioned with the

same notch orientation.

Safety guidelines you should know and follow include:

• Read the owner’s manual and follow all operating instructions.

• Visually check the EFX 5.33 before beginning service or maintenance operations. If it is not

completely assembled or is damaged in any way, exercise extreme caution while operating

and checking the EFX 5.33.

5.33 Elliptical Fitness Crosstrainer

Page 3

• When operating the EFX 5.33, do not wear loose clothing. Do not wear shoes with heels or

leather soles. Check the soles of your shoes and remove any embedded stones. Tie long

hair back.

• Do not rock the unit. Do not stand or climb on the handlebars, display enclosure, or cover.

• Do not set anything on the handlebars, display enclosure, or cover. Never place liquids on

any part of the EFX 5.33 other than a water bottle in the water bottle holder during normal

operation.

• To prevent electrical shock, keep all electrical components, such as the power cord and

circuit breaker away from water and other liquids.

• Do not use accessory attachments that are not recommended by the manufacturer-such

attachments might cause injuries.

General Information

For the latest exploded view, part number and part pricing information, visit the Precor dealer

website at “www.precor.com/connection.

5.33 Ellipitical Fitness Crosstrainer

Page 4

Required Tools and Equipment

The following list is a summary of the tools and equipment required when you service Precor’s

EFX 5.33.

TOOLS EQUIPMENT

phillips and flat-head screwdrivers anti-static wrist strap (20024-101)

digital multimeter

standard and metric allen wrench sets

open-end wrench set Supplies

blue loctite

drive ratchet and ratchet set

socket drive allen set cable ties

chip puller Spares

rubber mallet interconnect cables

snap ring pliers

100 ft./lb. torque wrench

300 in./lb. torque wrench

belt gauge (part # 20030-117)

5.33 Elliptical Fitness Crosstrainer

Page 5

Procedure 2.1 - Accessing the Diagnostic Program

The EFX 5.33 diagnostic software cycles through the following tests:

• Display Test

• Keyboard Test

• Heart Rate Test

• Brake (eddy current) Test

Procedure

1. Plug the power cord into the wall outlet, then turn on the EFX 5.33 with the on/off switch.

Note:

For the purpose of entering the key sequences to access the various diagnostic programs, the

keypad keys are hypothetically numbered from 1 to 7 from left to right.

2. With the PRECOR EFX 5.33 banner displayed, access the diagnostic program by pressing,

keys RESET,5,1,7,6,5,7,6,1, sequentially.

Diagram 2.1 - 5.33 Display

Key #1

Key #3 Key #5

Key #7

5.33 Ellipitical Fitness Crosstrainer

Page 6

3. Watch the display as the LED test progresses. The test is programmed to display the

following LED illumination sequence:

a. The test name “DISPLAY” will be displayed for 2 seconds.

b. The left half of the L.E.D. matrix illuminates.

c. The right half of the L.E.D. matrix illuminates.

d. All remaining L.E.D.’s, including the heart rate and annunciator L.E.D.’s illuminate.

4. If you do not observe the LED illumination sequences described in Step 3...

THEN... OTHERWISE...

Replace the upper PCA as described The LED test passed successfully;

in Procedure 7.2. continue with the next step.

5. Press the ENTER key to proceed to the keyboard test.

6. The test name “KEYBOARD” will be displayed for 2 seconds.

7. A graphical representation of all the keys on the keyboard will be displayed. When a key is

pressed the representation of the key will be turned “off”. Check all of the keys on the

keyboard in this manner.

THEN... OTHERWISE...

The keyboard test passed successfully; Troubleshoot the keypad and upper

continue with the next step. PCA as described in Procedure 6.2.

8. Press and hold the ENTER key to proceed to the heart rate test.

9. The test name “HEART RATE” will be displayed for 2 seconds.

10. A chest strap heart rate transmitter or a heart rate test transmitter must be used in

conjunction with this test.

11. If no heart rate signal is being received, the message NO HR RCVR will be displayed.

12. When a heart rate signal is being received, unfiltered (U 123) and filtered (F 123) heart rate

signals will be displayed. All of the Smart Rate L.E.D.’s will turn on and the Smart Rate

L.E.D. associated with the heart rate being received will flash each time a heart beat is

detected.

13. Press the ENTER key to proceed to the brake test.

14. The test name “BRAKE” will be displayed for 2 seconds.

5.33 Elliptical Fitness Crosstrainer

Page 7

15. The resistance level will be displayed on the left side of the display and the corresponding

power bits (duty cycle) will be displayed on the right side of the display. Initially, the power

bits level will be zero, pressing the , keys will change the number of power bits being

applied to the eddy current system.

16. Press the ENTER or RESET key to exit the diagnostics program.

5.33 Ellipitical Fitness Crosstrainer

Page 8

Procedure 2.2 - Accessing the Information Display

Procedure

1. Plug the power cord into the wall outlet, then turn on the EFX 5.33 with the on/off switch.

2. With the PRECOR EFX 5.33 banner displayed, press keys RESET,6,5, sequentially.

The EFX 5.33 Information display cycles through the following displays:

a. Odometer

b. Hour meter

c. Software version

d. Error log

5. The display name “ODOMETER” will be displayed for 2 seconds. Then the odometer value

will be displayed, as total strides accumulated.

6. Press the ENTER key to proceed to the hour meter display.

7. The display name “HOUR METER” will be displayed for 2 seconds. Then the hour meter

value will be displayed, as the total number of hours of use. Fractional parts of an hour are

stored internally, the display will be truncated to the nearest full hour.

8. Press the ENTER key to proceed to the software version display.

9. The display name “SW VERSION” will be displayed for 2 seconds.

10. The upper software version (UPPER X.XX) will be displayed. Pressing either SELECT key

will toggle between the upper and lower software version display.

11. Press the ENTER key to proceed to the error log display

12. The display name “ERROR LOG” will be displayed for 2 seconds.

13. The first error log entry will be displayed (1: ERXX).

14. Pressing the , keys will move you through the log entries. Entry 1 will be the most recent

error log entry, with each succeeding entry being older than the preceding entry.

15. Pressing the SELECT key will toggle the display between the log entry (ERROR), the

odometer reading (STRIDES) when the error occurred and the hour meter (HOURS) when

the error occurred.

5.33 Elliptical Fitness Crosstrainer

Page 9

16. Pressing and holding the QUICK START key for 2 seconds will cause the prompt CLEAR?

to be displayed, holding the QUICK START for an additional 2 seconds will clear all existing

entries from the error log. The display will confirm that the error log has been cleared by

displaying OK. The display will revert to the first log entry and show it as a null entry (1: ---).

If the QUICK START key is not held for a minimum of 4 seconds, the error log will not be

cleared.

17. Press the ENTER or RESET key to exit the information display program.

5.33 Ellipitical Fitness Crosstrainer

Page 10

Procedure 2.3 - Accessing the Set User Parameters Display

Selecting United States standard units causes information to be displayed in miles. Information is

displayed in kilometers if metric units are selected. After you select a measurement standard, the

software accumulates and records workout information in the units of the measurement standard

selected.

Procedure

1. Plug the power cord into the wall outlet, then turn on the EFX 5.33 with the on/off switch.

2. With the PRECOR EFX 5.33 banner displayed, press keys RESET,5,6,7,1, sequentially.

3. The display name “SELECT UNITS” will be displayed for 2 seconds.

4. One of two measurement standards will be displayed, U. S. Standard or Metric.

5. If U. S. Standard is selected, weights will be in pounds and distances will be in miles. If

Metric is selected, weights will be in kilograms and distances in kilometers.

6. If you wish to change the measurement standard...

THEN... OTHERWISE...

Use the or  keys to toggle Continue with the next step.

to an alternate measurement standard;

then continue with the next step.

7. Press the ENTER key to save the currently displayed selection and exit the set user

parameters display or press the RESET key to leave the selection unchanged and exit the

set user parameters display.

Other manuals for EFX 5.33

Table of contents

Other Precor Elliptical Trainer manuals

Precor

Precor Resolute RSL 324 Operating manual

Precor

Precor Resolute RSL 208 User manual

Precor

Precor EFX 885 Assembly Instructions

Precor

Precor Elliptical Fitness Crosstrainer EFX 5.21 User manual

Precor

Precor Resolute RSL 310 User manual

Precor

Precor C546i User manual

Precor

Precor EFX546 User manual

Precor

Precor Resolute RSL 414 User manual

Precor

Precor Discovery Series User manual

Precor

Precor EFX 425 User manual

Precor

Precor Resolute RSL 515 User manual

Precor

Precor EFX User manual

Precor

Precor Move Beyond EFX556 NAVY User manual

Precor

Precor Resolute RSL 314 User manual

Precor

Precor Elliptical Fitness Crosstrainer EFX 5.25 User manual

Precor

Precor Elliptical Fitness Crosstrainer EFX 5.25 User manual

Precor

Precor 5.21i User manual

Precor

Precor PRECISION SERIES User manual

Precor

Precor Resolute RSL 623 User manual

Precor

Precor 5.17 User manual

Precor

Precor EFX 556i Installation and operating instructions

Precor

Precor Discovery Series User manual

Precor

Precor EFX 600 Line User manual

Precor

Precor Resolute RSL 618 User manual

Popular Elliptical Trainer manuals by other brands

Weslo

Weslo Momentum 4.0 Elliptical Manuale d'istruzioni

Progear Fitness

Progear Fitness Air elliptical pro 1307 owner's manual

Torque Fitness

Torque Fitness XPLLP owner's manual

Octane Fitness

Octane Fitness PRO3700C Operation manual

Xterra

Xterra FS5.8e owner's manual

Bodyguard

Bodyguard E-40 user manual

Bonn Germany

Bonn Germany Concept 2.2 user manual

NordicTrack

NordicTrack E 9.2 Elliptical HASZNALATI UTASITAS

Vision Fitness

Vision Fitness X6600iNetTV Assembly guide

Matrix

Matrix MX-A5x owner's manual

SportsArt Fitness

SportsArt Fitness ECO-NATURAL Elite E874 owner's manual

Sears

Sears FREE SPIRIT C249 30737 0 owner's manual

True

True FS-64 Assembly manual

Sport-thieme

Sport-thieme ST 310 manual

VIRTUFIT

VIRTUFIT CTR 1.1 user manual

Kettler

Kettler GIRO C 1 manual

CIRCLE FITNESS

CIRCLE FITNESS E7 owner's manual

Reebok

Reebok 1000 Zx Elliptical Manuel de l'utilisateur