Precor Resolute RSL 313 User manual
ENGLISH
Resolute™ Strength Selectorized Line
Back Extension RSL 313
Assembly Guide
©2019 Precor Inc. | Back Extension RSL 313 | Assembly Guide 3
Assembly Requirements
It takes about 90 minutes to assemble this equipment. If this is your rst time doing this, allow more time.
CAUTION
At least two people are required to assemble the equipment. DO NOT attempt to assemble this by yourself. Precor recommends that all strength equipment be bolted to the
ooring at all anchoring points.
Installation Requirements
● Unpack the boxes and assemble the equipment close to where you plan to use it.
● Locate equipment at least 40 inches (1 meter) away from any walls, furniture, or objects on all sides.
● While tightening the fasteners, be sure to leave room for adjustments. DO NOT fully tighten fasteners until instructed to do so.
● Set up and assemble the equipment on a solid, at surface, so that it remains level and ble.
● DO NOT move the equipment without assistance.
Required Tools
● Torque wrench with torque range to at least 150 ft-lb (206 N-m) andt ts the following hex bits: 6, 8, and 10 mm
● Socket wrench sets, metric and standard, plus extensions
● Open-end wrench sets, metric and standard
● Hex wrench sets, metric and standard, plus extensions
●Box cutter
●Rubber mallet
● Retaining ring pliers - large, medium, and small
● Pliers - large, medium, and small
Trademarks
Resolute is a trademark and Precor is a registered trademark of Precor, Incorporated.
All other trademarks belong to their respective owners.
©2019 Precor Inc. | Back Extension RSL 313 | Assembly Guide 4
Part # Name Quantity Part # Name Quantity
Main frame 1 Back pad 1
Seat frame 1 Seat pad 1
Lower cross brace 1 Roller pad 1
Upper cross brace 1 Washer, rubber, black 1
Pivot arm 1Washers, domed, silver 2
Pivot cover 1 Weight labels 1
Roller pad cap 1 Hex head screws 5/16-inch x 1½-inch 2
Roller pad cap ring 1 Hole plug 1
Seat frame end cap 1 Socket head cap screws (SHCS) M12 x 35 mm 4
Weight stack tower frame 1Socket head cap screws (SHCS) M12 x 130 mm 2
Bumpers 4 Socket head cap screws (SHCS) M10 x 65 mm 2
Top plate assembly 1Socket head cap screws (SHCS) M10 x 40 mm 2
Add-on weight spacer, 2½-inch 1Button head cap screws (BHCS) M10 x 125 mm 2
Add-on weight 5 lb (2.2 kg) 1Button head cap screw (BHCS) M6 x 15 mm 1
Add-on weight handle 1Socket head cap screws (SHCS) M12 x 125 mm 6
Kick plate 1 Shoulder bolt M10 x 25 mm 1
Weight stack spacer, 3-inch 1Hex head screw 5/16-inch x 3-inch 1
Guide rods 2 Hex head screw 5/16-inch x 1-inch 2
Shroud, crown 1Nylon lock nuts, M12 2
Guide rod with cap 1Nylon lock nuts, M10 2
Counterweight 1Washers, 13 mm 12
Shroud, rear upper 1Washers, 11 mm 6
Shroud, front upper placard 1Washer, silver 13.5 mm ID x 35 mm OD 1
Shroud, rear lower 1Washers, 9 mm 5
Shroud, front lower 1Washer, 11 mm (for pivot cap) 1
Shroud, rear middle 1Retaining ring, 38 mm 1
Shroud, front middle (left and right) 2 Retaining ring, 35 mm 1
Top tray 1Weight plates 10 lb (4.5 kg) 19
Shroud, lower pulley cover 1Wave washer 1
1
10
11
12
13
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
3
30
31
32
33
34
37
39
4
40
42
43
44
45
46
47
48
49
6
7
8
9
2
5
14
Parts List
38
41
50
51
52
53
54
55
56
57
58
35
36
©2019 Precor Inc. | Back Extension RSL 313 | Assembly Guide 5
Seat Assembly
Image Hardware Instructions
11 hex head screw 5/16-inch x 3-inch
2 hex head screws 5/16-inch x 1½-inch
3 washers, 9 mm
Tool: Socket wrench, ½-inch with extension
Attach seat pad to seat frame .
CAUTION! Do not lose hardware in tube.
2 2 washers, 9 mm
2 hex head screw 5/16-inch x 1-inch
1 hole plug
Tool: Socket wrench, ½-inch with extension
1 seat frame end cap
Tool: Mallet
Attach back pad to seat frame .
CAUTION! Do not lose hardware in tube.
Tap seat frame end cap into top of seat frame .
2
2
2
53
31
36
46
53
2
30
53 47
37
9
2
30
31
37
46
47
9
53
53
36
©2019 Precor Inc. | Back Extension RSL 313 | Assembly Guide 6
Frame Assembly
DO NOT tighten fasteners until instructed to do so.
Have your assistant hold frame parts in place during assembly.
Image Hardware Instructions
12 M12 x 130 mm SHCS
4 washers, 13 mm
2 M12 nylon lock nuts
Tools: Hex wrench, 10 mm
Socket wrench, 19 mm
2 M10 x 125 mm BHCS
2 washers, 11 mm
Connect main frame to lower weight stack tower
and to kick plate .
Align to far right hole under lower pulley.
Insert both guide rod fasteners from user side to align the
kick plate. Hand tighten only. These will be temporarily
removed in a later step.
2 2 M12 x 35 mm SHCS
2 washers, domed
Tool: Hex wrench, 10 mm
Connect main frame to side of weight stack tower .
1
1
4
3
2
16
10
38
1
34
16
48
50
39
50
42
51
10
1
10
16
34
42
48
38
50
10
39
51
©2019 Precor Inc. | Back Extension RSL 313 | Assembly Guide 7
32 M12 x 125 mm SHCS
2 washers, 13 mm
Tool: Hex wrench, 10 mm
Connect lower cross brace to main frame .
42 M12 x 35 mm SHCS
2 washers, 13 mm
Tool: Hex wrench, 10 mm
Connect upper cross brace to main frame .
5 2 M12 x 125 mm SHCS
2 washers, 13 mm
Tool: Hex wrench, 10 mm
Connect lower cross brace to seat frame .
6 2 M12 x 125 mm SHCS
2 washers, 13 mm
Tool: Hex wrench, 10 mm
Connect upper cross brace to seat frame .
7Tools: Hex wrench, 10 mm
Socket wrench, 19 mm
Torque wrench
Gently rock the frame to align. Tighten all M12 fasteners to
a torque of 55 ft-lb (75 N-m).
Do not tighten the M10 screws installed in step 1 at this
time. They will be removed temporarily in a later step.
3
4
2
1
1
3
2
4
1
44
4
3
50
50 38
4
3
2
50
44
50
44
44
38
50
50
44
50
44
50
©2019 Precor Inc. | Back Extension RSL 313 | Assembly Guide 8
Moving Parts
Image Hardware Instructions
1Tool: Mallet Slide pivot arm onto shaft on main frame . Use a mallet to gently
tap frame so shaft goes through the arm and ensures room for retaining
ring.
2 1 retaining ring 35 mm
Tool: Retaining ring pliers
Secure pivot arm with retaining ring.
31 wave washer
1 washer, 11 mm
1 shoulder bolt M10 x 25 mm
Tool: Hex wrench, 6 mm
Slide pivot cover onto pivot arm and secure.
4 1 roller pad cap ring Snap roller pad cap ring onto roller pad .
5 Slide roller pad onto pivot arm shaft.
6 1 retaining ring 38 mm
1 roller pad cap
Tool: Retaining ring pliers
Secure roller pad with retaining ring and snap on roller pad cap.
1
5
54
5
6
45
56
58
8
32
5
55
7
1
6
7
8
5
5
5
5
32
45
54
55
56
58
©2019 Precor Inc. | Back Extension RSL 313 | Assembly Guide 9
Route the Cable
Image Hardware Instructions
1Tools: Socket wrench, 8 mm
Socket wrench, 4 mm
To route the cable around the lower pulley on the weight stack tower, remove
the cable retainer. Route the cable around the pulley and then replace the cable
retainer.
2 Tools: Hex wrench, 8 mm
Open-end wrench, 19 mm
Torque wrench
To route the cable to the upper pulleys of weight stack tower, remove the cable
retainers, route the cables, and replace the retainers. Tighten to 50 ft-lb (67 N-m)
of torque.
Finish the Weight Stack Tower
Image Hardware Instructions
12 M10 x 125 mm BHCS
2 washers, 11 mm
Tool: Hex wrench, 6 mm
Remove the guide rod fasteners installed in step 1 of the Frame Assembly.
2 2 guide rods
1 weight stack spacer, 3-inch
Align the weight stack spacer over the holes on the base of the tower. Insert two
weight guide rods and lean outwards about 6 inches (15 cm), enough clearance
for the weights. Flat side of weight stack spacer should face user side.
42
51
18
17
17
18
42
51
©2019 Precor Inc. | Back Extension RSL 313 | Assembly Guide 10
32 bumpers
19 10 lb (4.5 kg) weight plates
1 top plate assembly
Slide one bumper on to each rod. Place the weight plates on the rods. Ensure the
side with three holes face the user side and single hole to the back. Place the top
plate over the weight plates. The plates and top plate should align ush on the
user side.
41 M10 x 65 mm SHCS
2 washers, 11 mm
1 M10 nylon lock nut
Tools: Hex wrench, 8 mm
Socket wrench, 17 mm
1 guide rod with cap
Prepare the lower base for the add-on weight assembly. Place the retaining
screw through the bracket on the weight stack spacer.
Remove the cap from the guide rod and place the rod into bracket opening se-
cured by the screw.
5 2 bumpers
1 add-on weight spacer, 2½-inch
1 add-on weight
1 add-on weight handle
Place one bumper onto the third guide rod, followed by the add-on weight spac-
er, another bumper, the add-on weight, and the add-on weight handle.
6 1 counterweight Place counterweight over front two rods and handle.
12
57
11
49
20
40
51
15
14
11
13
11
21
11
12
13
15
20
21
40
49
14
51
57
11
©2019 Precor Inc. | Back Extension RSL 313 | Assembly Guide 11
7Straighten the front two guide rods to a vertical position. Have your assistant
lift the guide rods up into the upper part of the frame.
8 Tools: Hex wrench, 6 mm
Torque wrench
While the assistant is holding the rods into the upper frame, reinsert the two
bolts removed in step 1 underneath the guide rods in the bottom frame, and
secure to the kick plate. Let the guide rods drop onto the bolts and fully tight-
en the bolts. Tighten M10 screws to 32 ft-lb (43 N-m) of torque.
91 M10 x 65 mm SHCS
2 washers, 11 mm
1 M10 nylon lock nut
Tools: Hex wrench, 8 mm
Socket wrench, 17 mm
Replace the cap to the top of the rod and secure top of rod to weight stack
tower frame.
10 1 washer, rubber, black
1 washer, silver 13.5 mm ID x 35 mm OD
Place the washers into the top of the cable connector in the add-on weight
handle.
52
33
40
49
51
33
52
42
51
51
40 49
Other manuals for Resolute RSL 313
1
Table of contents
Other Precor Elliptical Trainer manuals
Precor
Precor EFX5.31 User manual
Precor
Precor Move Beyond EFX556 NAVY User manual
Precor
Precor EFX 825 User manual
Precor
Precor Resolute RSL 605 User manual
Precor
Precor EFX EFX 5.23 User manual
Precor
Precor EFX User manual
Precor
Precor EFX546 User manual
Precor
Precor Resolute RSL 204 User manual
Precor
Precor Discovery Series User manual
Precor
Precor EFX 5.33 User manual
Precor
Precor Precision 400 Series User manual
Precor
Precor EFX546 User manual
Precor
Precor 5.37 User manual
Precor
Precor HANDBOEK EFX 556i Installation and operating instructions
Precor
Precor Resolute RSL 620 User manual
Precor
Precor Resolute RSL 621 User manual
Precor
Precor Resolute RSL 505 User manual
Precor
Precor Experience Series User manual
Precor
Precor Resolute RSL 606 User manual
Precor
Precor Elliptical Fitness Crosstrainer EFX 5.21 User manual
Popular Elliptical Trainer manuals by other brands
Bonn Germany
Bonn Germany Concept 2.2 user manual
NordicTrack
NordicTrack E 9.2 Elliptical HASZNALATI UTASITAS
Vision Fitness
Vision Fitness X6600iNetTV Assembly guide
Matrix
Matrix MX-A5x owner's manual
SportsArt Fitness
SportsArt Fitness ECO-NATURAL Elite E874 owner's manual
Sears
Sears FREE SPIRIT C249 30737 0 owner's manual
