PR Lighting XPar 360 User manual

This manual suits for next models

1

Table of contents

Other PR Lighting Lighting Equipment manuals

PR Lighting

PR Lighting CUBIX300 User manual

PR Lighting

PR Lighting XR 1400 Framing User manual

PR Lighting

PR Lighting AQUA 580 BWS User manual

PR Lighting

PR Lighting PR-8836 User manual

PR Lighting

PR Lighting XR 380 BWS User manual

PR Lighting

PR Lighting PR-8846 User manual

PR Lighting

PR Lighting PR-8120 User manual

PR Lighting

PR Lighting PR5000 User manual

PR Lighting

PR Lighting PR-8170A User manual

PR Lighting

PR Lighting PR5000 User manual

PR Lighting

PR Lighting XL 1500 User manual

PR Lighting

PR Lighting Junior JNR-8142D User manual

PR Lighting

PR Lighting ARC LED 372 User manual

PR Lighting

PR Lighting XR250 User manual

PR Lighting

PR Lighting PR-2330 User manual

PR Lighting

PR Lighting XR130 Beam User manual

PR Lighting

PR Lighting TANGO SPOT User manual

PR Lighting

PR Lighting PR-111ER MOON User manual

PR Lighting

PR Lighting XLED 4007 BEAM User manual

PR Lighting

PR Lighting PR-6000 FRAMING User manual

PR Lighting

PR Lighting DESIGN 150 User manual

PR Lighting

PR Lighting PR-2203 XR 200 User manual

PR Lighting

PR Lighting XPar 150 Zoom User manual

PR Lighting

PR Lighting CHAMELEON PR-2012H User manual

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions

XPar 360

PR-8955

This product manual contains important information about the safe installation and use of this

projector. Please read and follow these instructions carefully and keep this manual in a safe place

for future reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

All manuals and user guides at all-guides.com

all-guides.com

2/17

INDEX

SAFE USAGE OF THE PROJECTOR 3

INSTALLING THE PROJECTOR 4

CONTROL SYSTEM AND POWER CONNECTIONS 4

DMX TERMINATOR 5

SETUP OPTIONS-PROJECTOR CONFIGURATION 5

TO SET THE DMX START ADDRESS 6

OPERATION MENU 7

DMX PROTOCOL 9

INDICATION OF LED DISPLAY 12

MAINTENANCE 12

TROUBLESHOOTING 12

TECHNICAL DATA 13

ELECTRICAL DIAGRAM 16

COMPONENT ORDER CODES 17

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without

notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of

product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence

arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good

condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the

unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.

ACCESSORIES

These items are packed together with the projector:

Name Quantity Unit Remark

Barn door 1 Pc Optional

Safety cord 1 Pc

This manual 1 Pc

Signal cable 1 Pc Optional

All manuals and user guides at all-guides.com

3/17

SAFE USAGE OF THE PROJECTOR

When unpacking and before disposing of the carton, check there is no transportation damage before using the projector.

Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.

The projector can be used indoors and outdoors, IP20.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.

Do not project the beam onto inflammable surfaces, minimum distance is 5m. 5m

Avoid direct exposure to the light from the lamp. The light is harmful to eyes.

Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector.

It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.

Do not connect this device to any other types of dimmer apparatus.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord come into contact

with other cables. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.

Keep the optical system clean. Do not touch the LED lens with bare hands.

When the projector is hanged to a high place, please use a safety cord provided to pass through the projector handles as

a secondary safety fixing for safety seasons. For details, refer to “INSTALL THE PROJECTOR “section.

LED lens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired,

for example by cracks or deep scratches.

Exterior surface temperatures of the projector after 5 minutes operation is 45℃, when achieving steady state it is50℃.

There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the

covers removed.

Always disconnect from the mains, when the device is not in use or before cleaning it or

before attempting any maintenance work !

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

All manuals and user guides at all-guides.com

4/17

INSTALL THE PROJECTOR

When the projector is used, as the right figure above, unfold the support to certain angle and put the projector onto a

flat surface. Make sure it is steady.

When the projector is used at a high place, as the left figure above, fold the support, turn it round to the top of the

projector, connect a lamp hook to the mounting hole reserved in the support by screws, and then hang the hook to a high

place. Eventually, use the safety cord provided to pass through the handles and hang it as a second safety fixing.

CONTROL SYSTEM AND POWER CONNECTION

Connection between the controller and a projector and between one projector and another must be made with a 2

core-screened cable, with each core having at least a 0.5mm diameter. Please use the projector’s cannon 3- pin signal

input and output cables as connection. The 3-pin signal connections are connected as shown in the figure above.

Note: Care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of

the plug is not connected in any way. The XPar 360 accepts digital control signals in protocol DMX512 (1990).

The amount of projectors connected in parallel is not more than 32. Connect the controller’s output to the first fixture’s

input cable with a 3-pin signal cable, connect the first fixture’s output cable to the second fixture’s input cable and connect

the rest fixtures in the same way. Eventually, connect the last fixture’s output cable to a DMX terminator. Note: Only when

all the start addresses of fixtures are set the same, synchronous control could be achieved.

When the first fixture is not connected to the controller, and all the other connections are the same as above, it is master /

slave mode connection. To achieve master / slave mode, set the first fixture master , the others salve( slave is default).

As for power connections, each projector has to be supplied separately by external power. Use the power cord of each

projector to connect the mains power directly, paying attention to the voltage and frequency marked on the panel of the

projector.

Lamp Hook Mounting Hole

Safety Cable

Support

FUNCTION

DMX IN

3

11

DMX OUT

3

22

3

2

PIN

1

1

GND

DATA +

DATA -

DMX512

All manuals and user guides at all-guides.com

5/17

All of the connections are as the figure below.

DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This

prevents electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120 (ohm) resistor connected across pins 2 and 3, which is

then plugged into the output socket on the last projector in the chain. The connections are illustrated below.

SETUP OPTIONS-PROJECTOR CONFIGURATION

Projector configuration can be set conveniently via push-button switch and LED display.

Launch the projector and press button ENTER for more than 5 seconds to unlock the panel, the LCD will show the

function menu of the projector, each main menu has its submenus and each submenu has a specific function. For

details, please see the “OPERATION MENU” section.

Press button UP or DOWN if you want to browse through the various Setup Options. Press button ENTER to save your

settings or enter the next menu. Press button UP or DOWN to change values(add or subtract)

Press button FUNC, it will return to the upper menu one by one or browse through the main menu.

DMX Controller

Power IN Power IN Power IN

DMX OUT DMX IN DMX OUT DMX IN XLR terminator

21

3

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

ENTERUP DOWN

FUNC

All manuals and user guides at all-guides.com

6/17

TO SET THE DMX START ADDRESS

Each Xpar360must be given a DMX start address so that the correct projector responds to the correct control signals.

This DMX start address is the channel number from which the projector starts to “listen” to the digital control information

being sent out from the controller. The Xpar360 have 3 DMX modes, which are standard mode，extended mode and

short mode. For example, the standard mode has 12 channels, so set the No. 1 projector’s address 001, No. 2

projector’s address 13, No. 3 projector’s address 25, No. 4 projector’s address 37, and so on.

Launch the projector. Press button ENTER for more than 5 seconds to unlock the panel.

Press button FUNC, UP or DOWN to find “AddR” menu.

Then press ENTER to show DMX address and press UP or DOWN to set DMX address.

At this time, the address will flash continuously. Press button ENTER to confirm and it means the setting has been

enabled.

Press button FUNC, it will return to the upper menu one by one.

All manuals and user guides at all-guides.com

all-guides.com

7/17

OPERATION MENU

1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL

AddR

(DMX address)

XXX

（XXX:1~512）

CNFG

(Config settings)

dmX

(DMX mode)

STd

(Standard mode)

EXT

(Extended mode)

SHRT

(Short mode)

dISP

(Display settings)

ON

OFF

(Shut off digital CRT without

pressing buttons in 5 minutes)

mORS

(Master /Slave Settings)

SLAV

(Slave)

mAST

(Master)

FACT

(Reset factory setup) yES

TRmd

(Transmit parameters) yES

INFO

(Information)

TImE

(Fixture usage time) XXXX

TEmP

(LED board temperature) XX

VER

(Version) X.X.X

TEST

(Test mode)

A

(Amber)

R

(

Red

)

G

(Blue)

B

(Blue)

W

(white)

ALLO

(Red/green/blue/white)

mENU

(Operation mode)

dmx

(DMX mode)

PR XX

(Preset memory, PR01~PR16）

ET XX

(User memory,ET01~ET16）

COL1

(Colour 1)

XX

(Number: 0~14)(3)

COL2

(Colour 2)

XX

(Number: 0~14)

COL3

(Colour 3)

XX

(Number: 0~14)

COL4

(Colour 4)

XX

(Number: 0~14)

Note:

1.ONLY one projector of a group connected by one signal cable could be set as Master. When the Master

functions, DMX control signal should be disconnected

2.When multiple projectors’ work together in synchronous control state, Parameters can be transmitted from the master

projector to the slave projectors such as DMX channel mode, Display setting status and operation mode (User memory

data is included). While data transmitted, other projectors will be set as SLAVE.

All manuals and user guides at all-guides.com

8/17

DMX PROTOCOL

Short

mode

Standard

mode

Extended

mode FUNCTION DMX DESCRIPTION

1 1 1 Dimmer 000-255 Dimming from dark to light

2 Dimmer Fine 000-255 Dimmer in 16 Bit precision

2 2 3 Colour Temperature

000 No effect

001-255 Colour temperature linear adjustment

from 3200K to 10000K

3 4 Macro Channel

0 No effect

001-015 Colour Temperature 3200K

016-031 Colour Temperature 5600K

032-047 Colour Temperature 7200K

048-063 Colour Temperature 10000K

064-079 Amber

080-095 Red

096-111 Green

112-127 Blue

128-143 White

144-159 Red & Green(Yellow)

160-175 Green & Blue(Cyan)

176-191 Red and Blue(Purple)

192-207 Red Green Blue and White

208-223 Full Power

224-239 Yellow and White

240-255 Amber Blue and White

3 4 5 Amber 000-255 Linear adjustment from dark to light

4 5 6 Red 000-255 Linear adjustment from dark to light

5 6 7 Green 000-255 Linear adjustment from dark to light

6 7 8 Blue 000-255 Linear adjustment from dark to light

7 8 9 White 000-255 Linear adjustment from dark to light

10 Hue 000-255 Hue selection

11 Saturation 000-255 Saturation from shallow to deep

12 Value 000-255 From dark to light

8 9 13 Strobe 000 No effect

001-255 Strobe speed from slow to fast

10 14 Preset memory

000 No effect

001-015 Preset memory 1

016-031 Preset memory 2

032-047 Preset memory 3

048-063 Preset memory 4

064-079 Preset memory 5

080-095 Preset memory 6

All manuals and user guides at all-guides.com

9/17

096-111 Preset memory 7

112-127 Preset memory 8

128-143 Preset memory 9

144-159 Preset memory 10

160-175 Preset memory 11

176-191 Preset memory 12

192-207 Preset memory 13

208-223 Preset memory 14

224-239 Preset memory 15

240-255 Preset memory 16

11 15 User Memory

000 No effect

001-015 User memory 1

016-031 User memory 2

032-047 User memory 3

048-063 User memory 4

064-079 User memory 5

080-095 User memory 6

096-111 User memory 7

112-127 User memory 8

128-143 User memory 9

144-159 User memory 10

160-175 User memory 11

176-191 User memory 12

192-207 User memory 13

208-223 User memory 14

224-239 User memory 15

240-255 User memory 16

12 16 Memory Speed

001-015 Speed 1,the fastest

016-031 Speed 2

032-047 Speed 3

048-063 Speed 4

064-079 Speed 5

080-095 Speed 6

096-111 Speed 7

112-127 Speed 8

128-143 Speed 9

144-159 Speed 10

160-175 Speed 11

176-191 Speed 12

192-207 Speed 13

208-223 Speed14

224-239 Speed 15

240-255 Speed 16, the slowest

All manuals and user guides at all-guides.com

10/17

Note:

**** Channel priority from high to low is as the following: Dimming, Preset memory, User memory, ARGBW dimming,

HSV dimming, Macro channel, Color temperature.

****When high priority channel is used, low priority channel is No effect.

All manuals and user guides at all-guides.com