Politec ALES 60 User manual

ISTRUZIONI ALES60-120 INGLESE –VER1.2 –POLITEC s.r.l. 1 of 8

ALES 60/120

INFRARED PERIMETRALBARRIER

DOUBLE BEAMS

Installation Manual

ISTRUZIONI ALES60-120 INGLESE –VER1.2 –POLITEC s.r.l. 2 of 8

1.MAIN COMPONENT LIST

IR Cover

Terminals

Tamper

Switch

Horizintal Adjustment

Screw

Vertical Adjustment

Screw

Lens

Channel Selection

Adjustment

Buzzer

(RX)

Adjustment

High -

Frquence

Leds

(RX)

Mounting

Plate

“U” Bracket

For Pole

Mounting

Unit Base

Screws

TEST Button

ISTRUZIONI ALES60-120 INGLESE –VER1.2 –POLITEC s.r.l. 3 of 8

2.SUGGEST FOR INSTALLATION

For proper installation of the product is necessary to remove all possible obstacles between the

transmitter and receiver (trees, grass, etc..), Use for the installation immovable poles or walls

firmly anchored to the ground. You should also always use cables with screen for alarm

connections, proper sizing by taking more precautions due to electronic devices. To avoid

interfering with the performance and the degree of protection (IP) of the barrier is necessary to

take the necessary precaution, taking care not to alter seals, plastic and mechanical parts of the

product, using original accessories. In case of repairs covered by warranty (2 years) but with

obvious signs of improper installation, the Politec s.r.l. reserves the right to decide on any repair

costs.

Avoid installing the receivers beams in a position where direct sunlight, at the same angle as

the receivers beams, can enter directly into optics especially at sunset and sunrise

3. INSTALLATION

The barrier ALES can be installed to the wall using the mounting plate and the pole using the

mounting plate and the "U" bracket (Pole 48-50).

ISTRUZIONI ALES60-120 INGLESE –VER1.2 –POLITEC s.r.l. 4 of 8

-Wall-mounting:

1Insert the cable alarm screen in the hole of the plate and fix to the wall with screws.

2Pass the cable through the gasket in the base and anchor on the same plate. Make connections to

the terminal.

3Following the calibration and verification of proper operation of the system, replace the IR Cover.

-Pole-mounting:

1 Insert the screened cable for alarm in the hole of the plate and fix the plate to the pole using the

"U" bracket.

2 Pass the cable through the gasket in the base and anchor on the same plate. Make connections to

the terminal.

3Following the calibration and verification of proper operation of the system, replace the IR Cover.

ISTRUZIONI ALES60-120 INGLESE –VER1.2 –POLITEC s.r.l. 5 of 8

4.CONNECTIONS AND DESCRIPTIONS

TRANSMITTER/RECEIVER

1. Test Button (Only RX) –when pressed allows you to access the functions of alignment.

2. Dis Out (Only RX) –In case of disqualification activated gives output signal (NEGATIVE OPEN

COLLECTOR).

Terminals –

4. Dis On (Only RX) –With inserted jumper enables the environmental disqualification and the

monitoring output Dis Out.

5. Channel Selection –Moving the dip switch in ON (one at a time) enables a transmission

channel, the same set to the TX must be corresponding to that of the RX.

6. TMP1 –Tamper input additional, in case of absence MUST remain closed by jumper.

7. TMP –Tamper anti cover removal.

Alarm

Contact N.C.

(only RX)

TAMPER

Contact

Power Supply

10 –30 VDC

ISTRUZIONI ALES60-120 INGLESE –VER1.2 –POLITEC s.r.l. 6 of 8

5.FREQUENCY SELECTION

To compose barriers or dams with more than one pair of Ales, it is necessary to avoid interference

assign a different channel to each of them. To do this you must turn ON dip switches on the desired

channel on the mother board. The channel will be the same from both the transmitter from the

receiver (ex. CHTX1 / CHRX1 - CHTX4 / CHRX4).

6.ALLIGNMENT TEST

Press the TEST button on the RX mother board for 3 seconds until the buzzer will beep

twice, accompanied by two blinking of LEDs, to begin calibration.

1. Press the

TEST button

on the RX

Column

2.Power on of buzzer and LEDs on RX

column

ISTRUZIONI ALES60-120 INGLESE –VER1.2 –POLITEC s.r.l. 7 of 8

Align the optics placed in the column TX to RX, vertically and horizontally by turning the

adjustment screws (horizontal and vertical) to find the maximum alignment. The condition

of maximum alignment will be achieved when the LEDs are fixed and the buzzer will sound

continuously. The condition of partial or total misalignment is indicated by flashing LEDs

and low frequency whistle of buzzer.

After obtained the calibration tighten the screw for horizontal adjustment, and exit from

TEST mode by pressing the TEST button for 3 seconds on RX mother board. Two beeps of

buzzer will indicate the end of the TEST function.

7.ENVIRONMENTAL DISQUALIFICATION

To obtain the message in the control panel of environmental disqualification, you must insert the

jumper in DIS ON and connect a "OPEN COLLECTOR NEGATIVE" to the output DIS OUT. This

feature allows output to the control panel of environmental disqualification, for which the barrier is

in a standby state, this will avoid annoying false alarms caused by weather conditions.

1. Vertical Adjustment

2. Horizontal Adjustment

1. Insert jumper in DIS ON.

2. With the supplied cable connect

the output OUT DIS (open

collector negative) to bring the

output in the control panel.

ISTRUZIONI ALES60-120 INGLESE –VER1.2 –POLITEC s.r.l. 8 of 8

8.ADDITIONAL TAMPER

On mother boards TX and RX there is a supplementary Tamper input useful to add a wall tamper. In

case of absence of additional Tamper, Check the closing of the contact by a jumper.

9.TECHNICAL FEATURES

ALES 60/120

Max range indoors

250m/480m

Max range outdoors

60m/120m

Synchronization

Optic 4 Channels

Environmental Disqualification

Yes with open collector

Power supply

10-30VDC

Current consumption

90mA couple

Heaters

Optional with thermostat

Heaters consumption (couple)

10/15VDC250mA

TAMPER output

Contact NC

Operating temperature

-25° (with heat.) +65°

IPProtection

IP65

Mounting brackets for wall/pole

TOTALWARRANTY 2 YEARS

Tamper input additional, in case of absence

MUST be closed by jumpers.

Other manuals for ALES 60

This manual suits for next models

Table of contents

Other Politec Security System manuals

Politec

Politec PARVIS MES SMA Series User manual

Politec

Politec NAT SENSOR User manual

Politec

Politec ALES Series User manual

Politec

Politec PARVIS WS SMA User manual

Politec

Politec PARVIS MES SMA Manual

Politec

Politec SANDOR DUAL SMA User manual

Politec

Politec SANDOR QUAD ESA SMA Manual

Politec

Politec MANA MW Manual

Politec

Politec PARVIS HYBRID SMA User manual

Politec

Politec ALES WS Manual

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual