Planet WFT-801 User manual

Trademarks

Contents subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technol-

ogy Corp. The information in this manual is subject to

change without notice. All other trademarks belong to

their respective owners.

FCC Warning

This equipment has been tested and found to comply

with the regulations for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference when the equipment is operated in

a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not

installed and used in accordance with this user’s guide,

may cause harmful interference to radio communica-

tions. Operation of this equipment in a residential area

is likely to cause harmful interference, in which case the

user will be required to correct the interference at his

own expense.

CE Mark Warning

This is a Class B product. In a domestic environment,

this product may cause radio interference, in which case

the user may be required to take adequate measures.

Revision

User’s manual for PLANET Fast Ethernet Media Con-

verter

Multi-mode: WFT-801, WFT-802

Single-mode: WFT-802S15

WDM: WFT-806A20, WFT806B20

Rev 2.0 (Nov. 2004)

Part No. EM-WFT8v2

EM_WFT8v2.indd 2004/11/5, �� 11:321

Table of Contents

Chapter 1 OVERVIEW 1

Chapter 2 PRODUCT FEATURES 2

Chapter 3 MODEL LIST 3

Chapter 4 CHECKLIST 4

Chapter 5 DIP SWITCH 5

Chapter 6 INSTALLING THE CONVERTER 6

6.1 Used as a stand-alone converter 6

6.2 Used with WMC-1600R converter chassis 7

Chapter 7 MANAGE MEDIA CONVERTER 8

Chapter 8 LED INDICATORS 10

Chapter 9 LINK PASS THROUGH FUNCTION 11

Chapter 10 PRODUCT SPECIFICATION 13

EM_WFT8v2.indd 2004/11/5, �� 11:322

Chapter 1

OVERVIEW

Thank you for choosing the Smart 10/100TX to 100FX Media

Converter, The Media Converter introduced here provides one

channel media conversion between 10/100TX and 100FX.

About Media Converter

The Smart Media Converter utililizes a network technology

specied by IEEE802.3 10Base-T, IEEE802.3u 100Base-TX,

100Base-FX standards.

About Link Pass Through

When LLCF (Link Loss Carry Forward) is enabled, the ports do

not transmit a link signal until they receive a link signal from the

opposite port. Link loss is “carried forward” to the managed switch

or hub that is sending the link. LLCF can be used for either the

copper or ber ports.

When LLR (Link Loss Return) is enabled, the ber port’s

transmitter shuts down if its receiver fails to detect a valid receive

link. If one of the optical conductors is bad, the converter with LLR

enabled will return a no link condition to its link partner. LLR is

used to detect link problems only on the ber port.

EM_WFT8v2.indd 2004/11/5, �� 11:321

Chapter 2

PRODUCT FEATURES

= One-channel media conversion between 10/100TX and

100FX

= Fiber media allows: multi-mode fiber using ST, SC, LC or

MT-RJ connector; single-mode fiber using SC or single

SC WDM connector

= Auto-negotiation of speed and duplex mode on 10/100TX

port

= Supports Link Pass Through

= Supports Auto-MDI/MDIX for 100TX port

= DIP switch for configuring fixed half/full duplex modes

= DIP switch for setting to Forced mode or Auto-negotia-

tion

= DIP switch for setting the speed

= DIP switch for setting the LLCF, LLR function

= Store-and-forward mechanism

= Back-pressure & IEEE802.3x compliant flow control

= Full wire-speed forwarding rate

= Front panel status LEDs

= Used as a stand-alone device or with a chassis

= Hot-swappable when used with a Chassis System

= Manageable through Intelligent Chassis System

EM_WFT8v2.indd 2004/11/5, �� 11:322

Chapter 3

MODEL LIST

Your Fast Ethernet Converter comes with one of the following

models.

ðWFT-801 ST fiber connector

ðWFT-802 SC fiber connector

ðWFT-802S15

SC fiber connector

ðWFT-806A20

SC WDM (Tx:1310) fiber connector

ðWFT-806B20

SC WDM (Tx:1550) fiber connector

Models with last two numbered characters indicate the ber-

port is with "Single-Mode" optic ber connector and the number

indicates the maximum distance in km. The rest will be "Multi-

Mode" optic ber models.

In the following sections, the term "WFT-80X" indicates the

product family above.

EM_WFT8v2.indd 2004/11/5, �� 11:323

Chapter 4

CHECKLIST

Your WFT-80X carton should contain the following items:

ðThe Fast Ethernet Converter

ðAC-DC Power Adapter (Output: 7.5VDC, 1.5 A max.)

ðThis user’s manual

If any item is missing or damaged, please consult the dealer from

whom you purchased your Fast Ethernet Converter.

EM_WFT8v2.indd 2004/11/5, �� 11:324

Chapter 5

DIP SWITCH

There is a DIP switch for the setting on copper and ber port.

Refer to the table below for more details.

Switch 1

On Fiber Half Duplex

Off Fiber Full Duplex (default)

Switch 2

On TX Forced Mode

Off TX Auto-Negotiation(default)

Switch 3

On TX 10M

Off TX 100M (default)

Switch 4

On TX Half Duplex

Off TX Full Duplex (default)

Switch 5

On LLR Enable

Off LLR Disable (default)

Switch 6

On LLCF Enable

Off LLCF Disable (default)

EM_WFT8v2.indd 2004/11/5, �� 11:325

Chapter 6

INSTALLING THE CONVERTER

6.1 Used as a Stand-alone converter

Step 1- Turn off the power of the device in a network to which

the WFT-80X will be attached

Step 2- Ensure that there is no activity in the network

Step 3- Attach ber cable from the WFT-80X to the ber

network.

Step 4- TX, RX must be paired at both ends

Step 5- Attach a Cat. 5 UTP cable from the 10/100 Base- TX

network to the RJ-45 port on the WFT-80X.

Step 6- Connect the 7.5VDC power adapter to the WFT- 80X and

verify that the Power LED lights up.

Step 7- Turn on the power of the device, the TX Link and FX

Link LEDs should light when all cables are attached

 NOTE:

• RJ-45 Cat 5, straight-through cable is ac-

cepted

• Please refer to Chapter 10 for more about

the wiring distance of your TP, Optic-fiber

networks.

EM_WFT8v2.indd 2004/11/5, �� 11:326

6.2 Used with WMC-1600R converter chassis

Step 1- Unscrew and pull out the media converter board

Step 2- Remove a blank faceplate from an empty expansion slot

on the front of the chassis. The module can be installed in

any expansion slot.

Step 3- Slide the module into the expansion slot, aligning it with

the guiderails, until it rmly connects to the chassis’

backplane.

Step 4- Secure the module to the chassis by tightening the

thumbscrew.

EM_WFT8v2.indd 2004/11/5, �� 11:327

Chapter 7

MANAGE MEDIA CONVERTER

The Intelligent Media Coverter Chassis that can control this Smart

Media Converter through the management system, this Smart

Media Converter can be controlled through Web Browser, SNMP

management utility and terminal emulation program.

The Intelligent Chassis will detect the setting on the DIP switches

and display out the status, also the Management Chassis can

control the function through the maanagement system.

Through the Intelligent Media Converter

Chassis System, you can control the

setting of this Smart Media Converter,

to set the Fiber and UTP (FDX/HDX),

UTP (Auto-negotiation/Manual), Speed

(10M/100M), LLR Enable/Disable), LLCF

(Enable/Disable)

Device

Link

Setup

To enable or disable the connection of both

UTP port and Fiber port

LLCF

Setup

To enable or disable the LLCF function of the

device

M1 AN

Setup

To set the UTP to Auto-negotiation or Forced

Mode

Speed

Setup

To set the speed of UTP to 10M or 100M

M1 DUP

Setup

To set the Duplex Mode of UTP port to Full

or Half

M1 FC

Setup

To set the Flow Control of the UTP to enable

or disable

EM_WFT8v2.indd 2004/11/5, �� 11:328

This manual suits for next models

Table of contents

Other Planet Media Converter manuals

Planet

Planet SMART MEDIA CONVERTER GST-70X User manual

Planet

Planet IXT-900-1X1T User manual

Planet

Planet IFT-802 User manual

Planet

Planet FT-807 User manual

Planet

Planet vc-234 vdsl2 User manual

Planet

Planet EM-GT70X User manual

Planet

Planet Media Converter Chassis MC-1000R User manual

Planet

Planet ICS-2100 User manual

Planet

Planet XT-715A User manual

Planet

Planet GT-902 User manual

Planet

Planet ICS-2100 User manual

Planet

Planet WGT-702 User manual

Planet

Planet FT-807 User manual

Planet

Planet GST-702/702S User manual

Planet

Planet GT-805A User manual

Planet

Planet FT-90X FT-902S15 User manual

Planet

Planet GT-80X Series User manual

Planet

Planet VC-202 User manual

Planet

Planet GT-915A User manual

Planet

Planet VC-201A User manual

Planet

Planet FT-722 User manual

Planet

Planet VC-231G User manual

Planet

Planet ET-508 User manual

Planet

Planet IPOE-171S User manual

Popular Media Converter manuals by other brands

SoundTraxx

SoundTraxx Blunami BLU-2200 user guide

SPROLINK

SPROLINK VA1 user manual

Acclaim Lighting

Acclaim Lighting DDC-1-AC user guide

Nikon

Nikon AF-S TC-20E III user manual

Axis

Axis AXIS Q7406 user manual

Omega

Omega TAC80B-J instruction sheet

Zoom

Zoom Thunderbolt TAC-2R Operation manual

OST

OST iConverter 10/100M quick start guide

Vertiv

Vertiv Netsure user manual

birddog

birddog MINI user guide

Roland

Roland GI-10 owner's manual

Wallenstein

Wallenstein WX310 Operator's manual

Pace

Pace MSS 200-1 Service manual

Solar Converters

Solar Converters EQ 12/24-50 manual

CYP

CYP EL-7400V Operation manual

TIE

TIE MIDI 1i1o user manual

DCS

DCS Vivaldi Upsampler user manual

Westermo

Westermo MCW-211 SERIES user guide