Planet ET-508 User manual

ET-509A

TP-BNC Converter

ET-508 /ET-508S

TP-Fiber (Multi-mode / Single-mode)

IEEE802.3 Ethernet Converter

1. Overview

IEEE802.3 10Mbps Ethernet supports various type media for network connection such as

10Base-2, 10Base-T and 10Base-FL. The media converter is used to convert one type

media signal to other type equivalent that allows multiple type segments connect easily and

inexpensively. This converter can be used as a standalone unit or as a slide-in module to the

19" Media Chassis (up to 10 units) for use at a central wiring closet.

2. Model Description

Model Descripton Connector Type

ET-508S TP-FL (Fdx/Hdx supported) RJ-45 ↔10Base-FL ST (SM)

ET-508 TP-FL (Hdx) RJ-45 ↔10Base-FL ST (MM)

ET-509A TP-BNC RJ-45 ↔10Base-2 BNC

The available Fiber –optic mode

ST, MM ST type connector, Multi-Mode

ST, SM ST type connector, Single-Mode

3. Checklist

Before you start installing the Converter, verify that the package contains the following:

The Converter

AC-DC Power Adapter

This User's Manual

T-Connector(for ET-509A only)

Please notify your sales representative immediately if any of the aforementioned items is

missing or damaged.

4. Panel Layout

10Mbps ET-508/ ET-508S Front and Side Panel

10Mbps ET-509A Front and Side Panel

Power Input +5VDC Jack on Rear Panel

5. Installing the Converter

For as a standalone unit:

⇒Verify the Ac to DC adapter conforms to your country

AC power requirement and insert the power plug

⇒Connect the media cable for network connection

For as a slide-in unit:

⇒The slide-in Media Converter and Converter Rack should be supplied only from

the same source, both Media Converter and Rack are built to match each other at

dimensions, DC jack, DC receptacle and power safety

⇒Turn off the 19" converter rack power

⇒Locate +5VDC power jack on converter back, carefully slide in and plug to 19"

rack +5VDC power receptacle

⇒Ensure that there is no activity in the network

⇒Connect the media cable for network connection

⇒Turn on the converter rack power, the Power LED will light up

Fiber Port: Attach the fiber cable. The Tx, Rx fiber cable must

be paired at both ends

TP Port: Attach UTP Cat. 3 or 5 cable to TP port

MPR : To a Hub or Repeater

DTE : To a workstation or NIC

Slide switch "DTE" / "MPR" is on the side panel.

Default: MPR

BNC Port: Attach T-Connector to BNC port and

connect the RG-58 coaxial network.

Ensure the coaxial cable/segment is

terminated at both ends properly

Note:

•Either DTE or MPR can be used at a time, do not attach both ports in

network connection.

•10Base-T port for cabling connections:

DTE: To a UTP workstation

MPR : Up-link to a Hub or Repeater

•ET-509A is an Ethernet Repeater, a maximum of four repeaters may used

between any two stations.

6. Connecting to 10/100Mbps N-Way Device

Converter Model 10/100 NWay Inter-operating

ET-508S* Single mode

TP-Fiber Converter

(Fdx/Hdx)

Non-Nway, it supports 10Mbps

only. Force the NWay partner

to 10Mbps speed at Fdx or Hdx

manully.

ET-508 Multi mode

TP-Fiber Converter (Hdx) 10/100Mbps is auto-sensing

and comes to 10Mbps Hdx

TP-BNC Converter 10/100Mbps is auto-sensing

and comes to 10Mbps Hdx

lET-508S support Full-duplex mode operation that can double the bandwidth, please make sure the

TP ends device also support full-duplex and set to it as well.

lET-508/ ET-509A support Hlaf-duplex mode only.

7. LED Description

ET-508/ ET-508S TP-Fiber Converter:

LED Color Function

Link/Act Green Lit when Fiber connection is good

Blinks when any FL traffic is present

Link/Act Green Lit when TP cable connection is good

Blinks when any FL traffic is present

Power Green Lit when +5V power is coming up

Collision Amber Blinks when any collision is present

ET-509A TP-BNC Converter:

LED Color Function

BNC Act Green Blinks when BNC traffic is present

Power Green Lit when +5V power is coming up

Link/Act Green Lit when TP connection is good

Blinks when TP traffic is present

Collision Amber Blinks when any collision is present

8. ET-508/508S Technical Specifications

•Models :a. ET-508S: Fdx/Hdx TP-Fiber Converter

b. ET-508: Hdx TP-Fiber Converter

•Standards :IEEE802.3 10Base-T/10Base-FL

•TP Port :RJ-45 jack with a slide switch for

"DTE" or "MPR" selection

Fiber Port :ET-508 (ST multi-mode)

ET-508S (ST single-mode),

•UTP Cable :Cat. 3 or 5 cable up to 100m

Fiber Cable:

50/125, 62.5/125, or 100/140µm multi-mode

8.3/125, 8.7/125, 9/125 or 10/125µm single-mode

Warning: To prevent from component damage, please check the cable and the

your duplex mode fiber device in the other ends before power on

10Base-FL ST/SC Fiber Cable Limitations:

Fiber Half/Full-duplex Multi-mode: 2Km

Fiber Full-duplex Single-mode: 10Km

•Data Transfer Rate:

10Mbps at half-duplex

(20Mbps for full-duplex mode only)

•LED Indicators :

FL Link/Act, Power, TP Link/Act, Col

•Power Requirement : 1A@+5VDC

•Ambient Temperature :0°to 50°C

•Humidity :5% to 90%

•Dimensions : 26.2(H) ×70.3(W) ×94(D) mm

Note: Connecting to Router, Bridge, or Switch, Hub, please refer to the device's

Technical Manual.

9. TP-BNC Technical Specifications

•Standards :IEEE802.3 10Base-T/10Base-2

•TP Port :RJ-45 jack with a slide switch for

"DTE" or "MPR" selection

BNC Port :BNC connector

•Cable and Distance :

Category 3/5 unshielded or shielded twisted pair (UTP/STP) wire, maximum length

100 meters (328ft)

0.2 inch diameter RG-58A/U, 50Ω(ohm) coaxial cable, maximum length 185

meters(607ft)

•Data Transfer Rate:

10Mbps at Half-duplex mode

•LED Indicators :BNC/Act, Power, TP Link/Act, Col

•Power Requirement : 1A@+5V

•Ambient Temperature:0°to 50°C

•Humidity :5% to 90%

•Dimensions : 26.2(H) ×70.3(W) ×94 mm(D)

10. DC Power Jack and AC-DC Power Adapter

The DC jack's central post is 2.5mm wide, it conforms to the

DC receptacle(2.5mm) on the 19-inch Converter Rack slot.

DC Jack

2.5mm

DC Input:

1A@+5V

Keep the AC-DC adapter as spare

parts when Media converter is installed

in a 19-inch Media Converter Rack.

AC-DC power adapter

AC Input : 100∼240VAC 50/60Hz

DC Output: 1A@+5VDC

Part No.: EM-ET508V2

This manual suits for next models

Table of contents

Other Planet Media Converter manuals

Planet

Planet IXT-900 POE Series User manual

Planet

Planet ICS-100 User manual

Planet

Planet GTP-802 User manual

Planet

Planet VC-201A User manual

Planet

Planet Power over Ethernet Splitter POE-152S-12V User manual

Planet

Planet POE-161S User manual

Planet

Planet FT-712 User manual

Planet

Planet FT-701B User manual

Planet

Planet FT-902 User manual

Planet

Planet POE-173S User manual

Planet

Planet VC-201A User manual

Planet

Planet VC-102M User manual

Planet

Planet GT-902 User manual

Planet

Planet Media Converter Chassis MC-1000R User manual

Planet

Planet VF-101-T User manual

Planet

Planet IGT-1205AT User manual

Planet

Planet POE-151 User manual

Planet

Planet IECC-210T User manual

Planet

Planet VF-101G-KIT User manual

Planet

Planet SMART MEDIA CONVERTER GST-70X User manual

Planet

Planet FST-801 User manual

Planet

Planet POE-165S User manual

Planet

Planet IFT-802T User manual

Planet

Planet vc-231 User manual

Popular Media Converter manuals by other brands

SoundTraxx

SoundTraxx Blunami BLU-2200 user guide

SPROLINK

SPROLINK VA1 user manual

Acclaim Lighting

Acclaim Lighting DDC-1-AC user guide

Nikon

Nikon AF-S TC-20E III user manual

Axis

Axis AXIS Q7406 user manual

Omega

Omega TAC80B-J instruction sheet

Zoom

Zoom Thunderbolt TAC-2R Operation manual

OST

OST iConverter 10/100M quick start guide

Vertiv

Vertiv Netsure user manual

birddog

birddog MINI user guide

Roland

Roland GI-10 owner's manual

Wallenstein

Wallenstein WX310 Operator's manual

Pace

Pace MSS 200-1 Service manual

Solar Converters

Solar Converters EQ 12/24-50 manual

CYP

CYP EL-7400V Operation manual

TIE

TIE MIDI 1i1o user manual

DCS

DCS Vivaldi Upsampler user manual

Westermo

Westermo MCW-211 SERIES user guide