Philips TD6816/BB051P User manual

Safety information

The marking on the product certifies its conformity with the technical

regulations for user safety and electromagnetic disturbance which were

applicable on the date of approval in accordance with European Union

Directive No. N° 73/23/EEC, 89/336/EEC, 91/263/EEC and 93/68EEC.

Power requirements

This product requires an electrical supply of 230 volts, alternating

monophased current, excluding IT installations defined in standard

EN 60-950.

Warning:

The electrical network is classified as dangerous according to criteria in

the standard EN 60-950.

The only way to power down this product is by unplugging the power cable

from the electrical outlet. Make sure the electrical outlet is located close to

the apparatus and is always easily accessible.

It is recommended that this telephone be used as a complement to

another telephone which does not require mains power.

Safety precautions

•Do not allow the handset to come into contact with water.

•Do not open the handset or the charger. This could expose you to

high voltages. Contact our after-sales service for all repairs.

•Do not allow the charging contacts or the battery to come into

contact with conductive materials such as keys, paper clips, rings,

bracelets, etc.

•Make sure you insert the batteries with their polarities in the correct

position.

Contents 5

Contents

Introduction 2

Installing your extra handset 3

Deciding where to put the charger 3

Installing the charger on a horizontal surface 3

Mounting the charger on a wall 4

Charging your handset 5

Selecting the menu language 5

Registering your extra handset with your Onis base station 6

Changing the name of your base station 7

Using your extra handset 8

Making an outside call 8

Answering an outside call 9

Making an internal call 9

Answering an internal call 10

Using the handset loudspeaker 10

Managing the Baby Sit mode 10

Transferring calls 11

Managing a conference call 12

Locking the handset keypad 12

Using the battery saver 13

Maintenance 14

Changing the battery 14

Caring for your handset 15

Introduction6

Introduction

Yo u r Onis extra handset comprises:

•a charger,

•a handset,

•a power cable.

•2 standard AA/R6 rechargeable batteries.

This guide shows you how to install and use your Onis

extra handset.

Please refer to the corresponding Onis user manual for

information on:

•using the phonebook,

•using the answering machine (Onis memo and Onis Vox only),

•troubleshooting.

Note:

You should also refer to the manufacturer’s handbook

corresponding to the base station with which you are using this

handset.

Installing your extra handset 7

Installing your extra

handset

Deciding where to put the charger

•Place the charger near a main outlet supplying 220-240V at

50Hz.

•To reduce to a minimum any interference with other electronic

devices such as telephones, televisions, screens, etc. we

advise you to place your charger at least 50 cm from any other

electronic device.

•Place the charger on a flat surface as with the base station or

mount it on a wall.

•Significant obstacles such as concrete walls or metallic

supports (windows and door frames, partitions, etc.) will lessen

the communication range between the base station and the

handset.

Installing the charger on a horizontal

surface

Plug the power cable into the charger.

Plug the power cable into the wall socket.

Place the handset in the charger.

Installing your extra handset

Mounting the charger on a wall

Fix the screws (not supplied) according to the diagram

below.

Plug the power cable into the charger as shown on

page 7.

Mount the charger on the screws.

Plug the power cable into the wall socket.

Place the handset in the charger.

2 - 2.5 mm

8 mm

46 mm

1.5 - 2 mm

3 mm

Installing your extra handset 9

Charging your handset

Your handset is powered by 2 rechargeable AA/R6 batteries.

Before you use your handset for the first time, charge

it for at least 16 hours. This precaution helps to lengthen the

life of the battery.

To charge the handset, place it on the charger or on the base

station. The bsymbol will appear on the display to indicate that

the battery is charging.

When the bsymbol disappears, your handset is fully charged.

The charger must be connected to a power supply using the power

cable supplied.

Selecting the menu language

Press R, then press -until you reach SETUP

Press o.

MENU LANG is displayed.

Press o.

Press -or +to scroll through the language options.

Press oto choose a language.

A beep confirms that the language has been selected.

Tip

To ensure an optimum handset charge, replace the

handset on the charger regularly.

Installing your extra handset

Registering your extra handset with your

Onis base station

To register your extra handset with your base station, proceed as

follows:

Unplug the power cable of the base station, then plug it

in again.

The base station beeps to indicate that it is now in

registration mode.

Move the handset to be registered close to the base

station and press Ron the handset to enter menu

mode.

Press +to display SETUP

, then press o.

Press -until REGISTER is displayed, then press o.

CODE? is displayed.

Enter the registration code (this is given on a sticker

labelled “RC” under the base station). Press o.

The handset will search for a base station that is in

registration mode.

After a few seconds, the handset beeps and REGISTER

is displayed. In this case go to the next step.

If the handset cannot find a base station, FAILED will be

displayed, and you will need to try again.

Press Rto leave menu mode.

It is also possible to set the base station to registration mode using a

handset that has already been registered. Instead of step 1 above,

proceed as follows:

1. Press R, then press +to display SETUP

. Press o.

2. Press -until ADD HS is displayed. Press o.

3. Enter the registration code (this is given on a sticker labelled “RC”

under the base station). Press o.

Your handset beeps to indicate that the base station is now in

registration mode.

Installing your extra handset 11

Changing the name of your base station

The default name of your base station is “PHILIPS”. You can

change this name from your extra handset as follows:

Press R, then press + to display SETUP

. Press

Press -until BASE NAME is displayed, then press

If the base station has a name, this will be displayed. You

can delete the existing name using the +key. If the base

station has no name, BASE NAME? will be displayed.

Enter the new name (max. 8 characters) using the

handset keypad.

You can enter characters by pressing the key with the

required character on it one or more times.These characters

are engraved on the handset keypad. If you wish to enter

two successive characters which are on the same key, you

need to distinguish them by pressing the -key between the

two characters. You delete a character with the +key.

For example: to enter PHILIPS you would press the

following keys.

Press o. Press Rto leave menu mode.

744

-444 555 444 7 -7777

PH I L I P S

Using your extra handset12

Using your extra

handset

Making an outside call

Direct dialling

Press the tkey on the handset.

The tsymbol is shown on the display and you hear the dial

tone in the handset earpiece.

Dial the number using the number keys.

The number called is displayed for 10 seconds after the last

key is pressed.

If the number you enter is longer than 10 digits, the display

will scroll the number to the left to show the last digits.

To hang up, press tor replace the handset in the

charger.

The duration of your call in minutes and seconds is

displayed for 4 seconds.

Dialling with number preparation

This way of dialling allows you to make corrections to the number

before dialling.

Dial the number (up to 23 digits) before pressing the t

key. You can use the +key to make corrections by

cancelling the last digit entered.

If the number you enter is longer than 10 digits, the display

will scroll the number to the left to show the last digits.

Tip

If you want to see the whole number you have dialled so

far, press o.The number will scroll to the left if it is

longer than 10 digits.

This manual suits for next models

Table of contents

Other Philips Handset manuals

Philips

Philips Onis 380 Vox User manual

Philips

Philips Kala 200 User manual

Philips

Philips TD 6831 User manual

Philips

Philips ONIS 6816 User manual

Philips

Philips SOPHO C933 User manual

Philips

Philips DECT2250G - DECT 2250G Cordless Extension... User manual

Philips

Philips Zenia 300 Vox User manual

Philips

Philips DECT2251G/17 User manual

Philips

Philips CD 1550 User manual

Philips

Philips DECT2250G User manual

Philips

Philips SE888 User manual

Philips

Philips DECT 629 User manual

Philips

Philips DECT2251G User manual

Philips

Philips G355 User manual

Philips

Philips KALA TD6830 User manual

Philips

Philips C124 User manual

Philips

Philips SE565 User manual

Philips

Philips Xalio 300 Multihandset User manual

Philips

Philips VOIP1511B/37 User manual

Philips

Philips Zenia 300 Vox User manual

Philips

Philips Onis 200 User manual

Philips

Philips Kala 300 Quattro User manual

Philips

Philips Xalio 300 Multihandset User manual

Philips

Philips ID9370B User manual

Popular Handset manuals by other brands

Swissvoice

Swissvoice ePure HD manual

ASCOM

ASCOM I62 - user manual

LG-Ericsson

LG-Ericsson LIP-9010 user guide

GE 1583 user guide

iiNet

iiNet Handset Quick installation guide

ASCOM

ASCOM 9p23 user guide

AT&T

AT&T DLP70110 user manual

AirCell

AirCell ST 3100 user manual

Eaton

Eaton HHIR-LCD-PROG Basic operations

Mitel

Mitel 112 manual

SBC

SBC SBC-381H installation manual

Mitel

Mitel 5602 user guide

ASCOM

ASCOM d81 Messenger Safety instructions

SpectraLink

SpectraLink 7522 quick start guide

Avaya

Avaya L100 Series Release notes

ooma

ooma HD2 Handset quick start guide

Yealink

Yealink IPW56 Quick reference guide

Sony

Sony SBH52 user guide