Philips TDA2613 User manual
DATA SHEET
Product specification
File under Integrated circuits, IC01 July 1994
INTEGRATED CIRCUITS
TDA2613
6 W hi-fi audio power amplifier
July 1994 2
Philips Semiconductors Product specification
6 W hi-fi audio power amplifier TDA2613
GENERAL DESCRIPTION
The TDA2613 is a hi-fi audio power amplifier encapsulated in a 9-lead SIL plastic power package. The device is
especially designed for mains fed applications (e.g. tv and radio).
Features
•Requires very few external components
•Input muted during power-on and off
(no switch-on or switch-off clicks)
•Low offset voltage between output and ground
•Hi-fi according to IEC 268 and DIN 45500
•Short-circuit-proof
•Thermally protected.
QUICK REFERENCE DATA
PACKAGE OUTLINE
TDA2613: 9-lead SIL; plastic power (SOT110B); SOT110-1; 1996 August 07.
Supply voltage range VP15 to 42 V
Output power at THD = 0,5%,
VP= 24 V Potyp. 6 W
Voltage gain Gvtyp. 30 dB
Supply voltage ripple rejection SVRR typ. 60 dB
Noise output voltage Vno(rms) typ. 70 µV
July 1994 3
Philips Semiconductors Product specification
6 W hi-fi audio power amplifier TDA2613
PINNING
1. n.c. not connected 5. GND ground (asymmetrical) or
2. n.c. not connected negative supply (symmetrical)
3. VP/2 1⁄2VP(asymmetrical) or 6. OUT output
ground (symmetrical) 7. +VPpositive supply
4. n.c. not connected 8. INV inverting input
9. −INV non-inverting input
Fig.1 Block diagram.
July 1994 4
Philips Semiconductors Product specification
6 W hi-fi audio power amplifier TDA2613
FUNCTIONAL DESCRIPTION
This hi-fi power amplifier is designed for mains fed applications. The device is intended for asymmetrical power supplies,
but a symmetrical supply may also be used. An output power of 6 watts (THD = 0,5%) can be delivered into an 8 Ωload
with an asymmetrical power supply of 24 V.
The gain is fixed internally at 30 dB. Internal gain fixing gives low gain spread.
A special feature of this device is a mute circuit which suppresses unwanted input signals during switching on and off.
Referring to Fig.4, the 100 µF capacitor creates a time delay when the voltage at pin 3 is lower than an internally fixed
reference voltage. During the delay the amplifier remains in the DC operating mode but is isolated from the non-inverting
input on pin 9.
Two thermal protection circuits are provided, one monitors the average junction temperature and the other the
instantaneous temperature of the power transistors. Both protection circuits activate at 150 °C allowing safe operation to
a maximum junction temperature of 150 °C without added distortion.
RATINGS
Limiting values in accordance with the Absolute Maximum System (IEC 134)
Note to the Ratings
For asymmetrical power supplies (at short-circuiting of the load) the maximum supply voltage is limited to VP= 28 V.
If the total internal resistance of the supply (RS)≥4Ω, the maximum unloaded supply voltage is increased to 32 V.
For symmetrical power supplies the circuit is short-circuit proof to VP= ±21 V.
PARAMETER CONDITIONS SYMBOL MIN. MAX. UNIT
Supply voltage VP−42 V
Non-repetitive peak
output current IOSM −4A
Total power dissipation see Fig.2 Ptot
Storage temperature range Tstg −55 +150 °C
Junction temperature Tj−150 °C
Short-circuit time: see note
outputs short-circuited
to ground
(full signal drive) tsc −1 hour
July 1994 5
Philips Semiconductors Product specification
6 W hi-fi audio power amplifier TDA2613
THERMAL RESISTANCE
HEATSINK DESIGN EXAMPLE
With derating of 8 K/W, the value of heatsink thermal resistance is calculated as follows:
given RL= 8 Ωand VP= 24 V, the measured maximum dissipation is 4,1 W; then, for a maximum ambient temperature
of 60 °C, the required thermal resistance of the heatsink is:
Note: The metal tab (heatsink) has the same potential as pin 5 (GND).
From junction to case Rth j-c = 8 K/W
Fig.2 Power derating curve.
Rth h-a 150 60–
41,
---------------------- 814K/W≈–=
July 1994 6
Philips Semiconductors Product specification
6 W hi-fi audio power amplifier TDA2613
CHARACTERISTICS
PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT
Supply voltage range
operating mode VP15 24 42 V
input mute mode VP4−10 V
Repetitive peak
output current IORM 2.2 −−A
Operating mode: asymmetrical power supply; test circuit as per Fig.4;
VP= 24 V; RL= 8 Ω; Tamb = 25 °C; f = 1 kHz
Total quiescent current Itot 10 20 35 mA
Output power THD = 0,5% Po56 −W
THD = 10% Po6,5 8,0 −W
Total harmonic
distortion Po= 4 W THD −0,15 0,2 %
Power bandwidth THD = 0,5%;
note 1 B −20 to 16 k −Hz
Voltage gain Gv29 30 31 dB
Noise output voltage
(r.m.s. value);
unweighted (20 Hz
to 20 kHz) RS= 2 kΩVno(rms) −70 140 µV
Input impedance |Zi|142026kΩ
Supply voltage
ripple rejection note 2 SVRR 35 44 −dB
Input bias current Iib −0,3 −µA
DC output offset with respect
voltage to VP/2 Vos −30 200 mV
Input mute mode: asymmetrical power supply; test circuit as per Fig.4;
VP= 8 V; RL= 8 Ω; Tamb = 25 °C; f = 1 kHz
Total quiescent current Itot 515 20mA
Output voltage Vi= 600 mV Vout −2,0 2,8 mV
Noise output voltage
(r.m.s. value);
unweighted (20 Hz
to 20 kHz) RS= 2 kΩVno(rms) −70 140 µV
Supply voltage
ripple rejection note 2 SVRR 35 55 −dB
DC output offset with respect
voltage to VP/2 Vos −40 200 mV
July 1994 7
Philips Semiconductors Product specification
6 W hi-fi audio power amplifier TDA2613
Notes to the characteristics
1. Power bandwidth at Po max −3 dB.
2. Ripple rejection at RS= 0 Ω, f = 100 Hz to 20 kHz;
ripple voltage = 200 mV (r.m.s. value) applied to positive or negative supply rail.
Operating mode: symmetrical power supply; test circuit as per Fig.3;
VP= ± 12 V; RL= 8 Ω; Tamb = 25 °C; f = 1 kHz
Total quiescent current Itot 10 20 35 mA
Output power THD = 0,5% Po56 −W
THD = 10% Po6,5 8,5 −W
Total harmonic distortion Po= 4 W THD −0,13 0,2 %
Power bandwidth THD = 0,5%
note 1 B −40 to 16 k −Hz
Voltage gain Gv29 30 31 dB
Noise output voltage
(r.m.s. value);
unweighted (20 Hz to
20 kHz) RS= 2 kΩVno(rms) −70 140 µV
Input impedance |Zi|142026kΩ
Supply voltage
ripple rejection SVRR 40 60 −dB
DC output offset with respect
voltage to ground Vos −30 200 mV
PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT
July 1994 8
Philips Semiconductors Product specification
6 W hi-fi audio power amplifier TDA2613
APPLICATION INFORMATION
Fig.3 Test and application circuit; symmetrical power supply.
Fig.4 Test and application circuit; asymmetrical power supply.
July 1994 9
Philips Semiconductors Product specification
6 W hi-fi audio power amplifier TDA2613
Input mute circuit
The input mute circuit operates only during switching on and off of the supply voltage. The circuit compares the 1⁄2supply
voltage (at pin 3) with an internally fixed reference voltage (Vref), derived directly from the supply voltage. When the
voltage at pin 3 is lower than Vref the non-inverting input (pin 9) is disconnected from the amplifier. The voltage at pin 3
is determined by an internal voltage divider and the external 100 µF capacitor.
During switching on, a time delay is created between the reference voltage and the voltage at pin 3, during which the
input terminal is disconnected, (as illustrated in Fig.5).
Fig.5 Input mute circuit; time delay.
July 1994 10
Philips Semiconductors Product specification
6 W hi-fi audio power amplifier TDA2613
PACKAGE OUTLINE
UNIT AA
max.
2A3b1D1
b2
bcD
(1) E(1) Z
max.
(1)
eLPP
1q
1
q
2
q
REFERENCES
OUTLINE
VERSION EUROPEAN
PROJECTION ISSUE DATE
IEC JEDEC EIAJ
mm 18.5
17.8 3.7 8.7
8.0
A4
15.8
15.4 1.40
1.14 0.67
0.50 1.40
1.14 0.48
0.38 21.8
21.4 21.4
20.7 6.48
6.20 3.4
3.2
2.54 1.0
5.9
5.7
4.4
4.2
3.9
3.4 15.1
14.9
Q
1.75
1.55
DIMENSIONS (mm are the original dimensions)
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
2.75
2.50
SOT110-1 92-11-17
95-02-25
0 5 10 mm
scale
0.25
w
D
E
A
A
c
A2
3
A4
q1q2
L
Q
wM
b
b1
b2
D1
P
q
1
Ze
19
P
seating plane
pin 1 index
SIL9MPF: plastic single in-line medium power package with fin; 9 leads SOT110-1
Table of contents
Other Philips Amplifier manuals
Philips
Philips TDA6111Q User manual
Philips
Philips SWS2063W User manual
Philips
Philips TDA7053A User manual
Philips
Philips PM 3342 User manual
Philips
Philips 22RH720 User manual
Philips
Philips FA741/00 User manual
Philips
Philips BGY280 User manual
Philips
Philips TDA4860 User manual
Philips
Philips TDA7050 User manual
Philips
Philips TDA6106Q User manual
Philips
Philips TDA8560Q User manual
Philips
Philips BGY580 User manual
Philips
Philips MC1458 Owner's manual
Philips
Philips FA 911 User manual
Philips
Philips TDA8925 User manual
Philips
Philips SA741C Owner's manual
Philips
Philips CMP400/55 User manual
Philips
Philips PM 3344 User manual
Philips
Philips DFA 888 User manual
Philips
Philips TDA8561Q User manual
