Perle IOLAN SCR1618 RDAC User manual
IOLAN SCR1618 RDAC
Quick Start Guide
_____________________________________
This guide covers basic installation and configuration and is
intended for first time setup or product evaluation.
Complete details can be found in the following guides at
www.perle.com/downloads.
•IOLAN SCR User’s Guide
•IOLAN SCR Command Line Reference Guide
•IOLAN SCR1618 RDAC Hardware Installation Guide
What’s in the box?
•IOLAN SCR Chassis
✓16 RS232 RJ45 Ethernet ports
✓16 RS232 serial RJ45 ports
•Quick Start Guide (this guide)
•Rack Mount Kit
What’s you need to supply
•Serial cables to connect serial devices to your IOLAN
•Ethernet CAT5e 10/100/1000BASE-T cables to connect
Ethernet devices to your IOLAN
Setting up the IOLAN SCR
1. Connecting dual or single power to the IOLAN SCR.
2. Configuring the IOLAN SCR.
3. Connecting Ethernet devices.
4. Connecting Serial devices.
IOLAN SCR1618 RDAC Quick Start Guide –5500463-11 (Rev B)
Version #A05.29.2020
SCR Front View
SCR Back View
Connecting the Power
Connect 1 or 2 power to power sources. Once power is
connected, the IOLAN will cycle through several sequences.
The LED 1, PWR 1 and 2 will show solid green when the
IOLAN is fully booted and ready to configure. If dual power
was used, then both PWR LEDs and LED 1 and 2 will be lit.
Setup Mode
Setup mode provides a simple method of doing an initial
setup from a PC. Your IOLAN is shipped in factory default
mode.
1. Complete the Connecting the Power step.
2. Set your PC to obtain an IP address automatically using
DHCP.
3. Plug your PC into any of the IOLAN’s Ethernet ports
(located on the back of the unit).
4. Use a standard web browser and enter http://192.168.0.1
to access your IOLAN.
On the setup screen, select, Getting Started.
5. Once connected, fill in the required fields, apply changes
to save and exit. The configuration changes will be
immediately applied to the IOLAN.
6. The IOLAN’s web configuration sign on screen will be
displayed. Using the credentials, you previously defined
in Step 4, you can now access your IOLAN’s full
configuration.
Connecting Ethernet Devices
The Ethernet RJ45 ports provide the standard Ethernet
interface speeds of 10/100/1000 Mbps. By default, all
10/100/1000 Ethernet ports will automatically set themselves
up to match the speeds of attached devices.
Ethernet Port
Connecting Serial Devices
Connect devices, workstations, servers or routers using a
straight through serial cable.
SFP Ports
The following SFPs are supported –1 Gbps fiber, 2.5 Gbps
fiber and SGMII copper.
Connecting the Fiber
Ensure that the cable implements the proper TX to RX
crossover. Once the device is connected and the link is
established the corresponding SFP LED will turn green.
© 2020 Perle Systems Limited. All rights reserved.
Other manuals for IOLAN SCR1618 RDAC
1
Table of contents
Other Perle Server manuals
Perle
Perle IOLAN SDS Instruction Manual
Perle
Perle IOLAN DG1 TX Manual
Perle
Perle IOLAN DS1 User manual
Perle
Perle SDS 1W User manual
Perle
Perle IOLAN SDS4 HL User manual
Perle
Perle IOLAN+ User manual
Perle
Perle JETSTREAM 4000 User manual
Perle
Perle IOLAN DS1 Instruction Manual
Perle
Perle IOLAN TG2 Manual
Perle
Perle IOLAN SCG User manual
Perle
Perle IOLAN SDS4 W Manual
Perle
Perle IOLAN DS1 G User manual
Perle
Perle IOLAN SDS2 LA Manual
Perle
Perle IOLAN SCG User manual
Perle
Perle IOLAN DS1 User manual
Perle
Perle 594M User manual
Perle
Perle IOLAN DS1 G Manual
Perle
Perle IOLAN SCR1618 RDAC Manual
Perle
Perle IOLAN DS1 User manual
Perle
Perle 833 User manual
