PEERLESS ST 640 Guide

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 01-13-06 SHEET #: 202-9030-2 01-30-06

Installation and Assembly:

Universal Tilt Wall Mounts

Features:

• Forflatpanelscreens

• One-touchtilt for effortless positioning and adjustment of the screen

• Ultra-slim design holds the screen flat against the wall

• IncreLok™ locking tilt positions for specific tilt settings in 5° increments

• Comes in black or silver

• Securityand Non-security models

Product is UL rated for screen size

range and load capacity per chart below

Model # Screen size range Max UL Load Capacity

ST640,ST640P, 23"-46" 150 lb (68 kg)

ST640-S, ST 640P-S,

RTFPT-220,RTFPT-220S

D-FPT-220,D-FPT-220S

ST650,ST650P, 32"-50" 175 lb (79 kg)

ST650-S, ST 650P-S

ST660,ST660P, 32"-60" 200 lb (91 kg)

ST660-S, ST 660P-S,

RTFPT2-320,RTFPT2-320S

D-FPT2-320,D-FPT-320S

ST670,ST670P, 42"-71" 250 lb (113 kg)

ST670-S, ST 670P-S

ST680,ST680P, 61"-102" 350lb(159 kg)

ST680-S, ST 680P-S

This product is UL Listed. It must be

installed by a qualified professional

installer.

2 of 24 ISSUED: 01-13-06 SHEET #: 202-9030-2 01-30-06

Note: Read entire instruction sheet before you start installation and assembly.

Tools Needed for Assembly

•studfinder("edge to edge" stud finder is recommended)

•phillipsscrewdriver

•drill

•1/4" bit for concrete and cinder block wall

•1/2" bit for metal stud wall

•5/32" bit for metal or wood stud wall

•level

Table of Contents

Parts List..............................................................................................................................................................................3

Installation to Double Wood Stud Wall..................................................................................................................................4

Installation to Triple Wood Stud Wall ....................................................................................................................................5

Installation to Solid Concrete or Cinder Block .......................................................................................................................6

InstallingTilt Brackets...........................................................................................................................................................7

Installing Flat Panel Screen to Wall Plate.............................................................................................................................8

Forcustomercare call (800) 729-0307 or (708) 865-8870.

Accessories

•4 piece Metal Stud Fastener Kit (ACC 415) (Metal Stud not evaluated by UL)

•2 piece Metal Stud Fastener Kit (ACC 215) (Metal Stud not evaluated by UL)

• DonotbegintoinstallyourPeerlessproduct until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please

callPeerless customer care at1-800-729-0307.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Makesurethat the supporting surface will safely support the combined load of the equipment and all attached hard-

wareand components.

• Neverexceedthe Maximum ULLoad Capacity.See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an

"edgetoedge" stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws firmly,butdo not overtighten. Overtightening candamagethe items, greatly reducing theirholding

power.

WARNING

3 of 24 ISSUED: 01-13-06 SHEET #: 202-9030-2 01-30-06

Penta-PinDriver(1)

M4 x 12 mm (6)

Adapter Bracket Fasteners

M4 x 25 mm (4)

M5 x 12 mm (4)

M5 x 25 mm (4)

M6 x 12 mm (4)

M6 x 25 mm (4)

M6 x 20 mm (4)

M6 x 30 mm (4) I.D. 6.5 mm (4) multi-washer(6)

Before you begin, make sure all parts shown are included with your product.

Parts may appear slightly different than illustrated.

M8 x 16 mm (6) M8 x 40 mm (6)M8 x 25 mm (4)

I.D. 8.7 mm (4)

I.D. 5.1 mm (4)

M10 x 15 mm (4)

I.D. 5.6 mm (4)

ST 640, ST 640P,

ST 640-S, ST 640P-S

RTFPT-220, RTFPT-220S,

D-FPT-220, D-FPT-220S

ST 650, ST 650P,

ST 650-S, ST 650P-S

ST 660, ST 660P,

ST 660-S, ST 660P-S

RTFPT2-320,

RTFPT2-320S,

D-FPT2-320,

D-FPT2-320S

ST 670, ST 670P,

ST 670-S, ST 670P-S

ST 680, ST 680P

ST 680S, ST 680PS

Parts List Non-Security Security

Black Silver Black Silver

Description Qty. Part Number Part Number Part Number Part Number

!AA wall plate (double stud) 1 200-1797 200-4797 200-1797 200-4797

!(double stud) 201-1026 201-4026 201-1026 201-4026

!(double stud) 201-1018 201-4018 201-1018 201-4018

!(triple stud) 200-1901 200-4901 200-1901 200-4901

!(triple stud) 200-1902 200-4902 200-1902 200-4902

!BB Left tilt bracket 1 200-0903 200-0905 200-0907 200-0909

!201-0031 201-0033 201-0027 201-0029

!200-0911 200-0913 200-0915 200-0917

!200-0919 200-0921 200-0923 200-0925

!200-0927 200-0929 200-0931 200-0933

!CC Right tilt bracket 1 200-0904 200-0906 200-0908 200-0910

!201-0032 201-0034 201-0028 201-0030

!200-0912 200-0914 200-0916 200-0918

!200-0920 200-0922 200-0924 200-0926

!200-0928 200-0930 200-0932 200-0934

!! ! DD #14 x 2.5 wood screw 4 5S1-015-C03 5S1-015-C03 5S1-015-C03 5S1-015-C03

!! 6 5S1-015-C03 5S1-015-C03 5S1-015-C03 5S1-015-C03

!! ! EE Alligator® anchor 4 590-0097 590-0097 590-0097 590-0097

!! 6 590-0097 590-0097 590-0097 590-0097

!FF 4 mm allen wrench 1 560-1131 560-1131 560-1131 560-1131

!! !! 560-1146 560-1146 560-1146 560-1146

I.D. 8.9 mm (6)

Note: The sorted-for-you™ fastener pack included was made specifically for your product and may not contain all components

shown below.

4 of 24 ISSUED: 01-13-06 SHEET #: 202-9030-2 01-30-06

Installation to Double Wood Stud Wall

Note: Ifmountingequipmentweighing greater than 200 lbs, triple stud mounting is strongly recommended.

Skip to page 5.

Wall plate (AA) can be mounted to two studs that are 16" apart. Use a stud finder to locate the edges of the studs.

Useof an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down each

stud’s center. Place wall plate on wall as a template. The top mounting slots should be 2.5" above the desired

screen center as shown in figure 1.1. Level plate, and mark the center of the four mounting holes. Make sure that the

mounting holes are on the stud centerlines. Drill four 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that

the wall plate is level, secure it using four #14 x 2.5" wood screws (DD) as shown in figure 1.2.

Note: Wall plate may be mounted up to 4" (102 mm) off center as shown in figure 1.1.

Skip to step 2 on page 7.

• Installermustverify that the supporting surface will safely support the combined load oftheequipmentandall attached

hardwareandcomponents.

• Tightenwoodscrews so that wall plate is firmly attached, butdonotovertighten. Overtightening can damage the

screws,greatly reducing their holdingpower.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is

highlyrecommended.

• Hardwareprovided is for attachment of mount throughstandardthickness drywall or plaster into woodstuds.Installers

areresponsible to provide hardwarefor other types ofmountingsituations.

WARNING

fig. 1.1

(102 mm)

2.5"

(64 mm)

(102 mm)

DD AA

fig. 1.2

CS = center of screen

STUD

5 of 24 ISSUED: 01-13-06 SHEET #: 202-9030-2 01-30-06

Installation to Triple Wood Stud Wall

fig. 1.3

CS = center of screen

(152 mm) 6"

(152 mm)

Wall plate (AA) can be mounted to three studs that are 16" apart. Use a stud finder to locate the edges of the studs.

Useof an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down each

stud’s center. Place wall plate on wall as a template. The top mounting slots should be 2.5" above the desired screen

center as shown in figure 1.3. Level plate, and mark the center of the six mounting holes. Make sure that the

mounting holes are on the stud centerlines. Drill six 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the

wall plate is level, secure it using six #14 x 2.5" wood screws (DD) as shown in figure 1.4.

Note: Whenmounting equipment weighing greater than 200 lbs, triple stud mounting is strongly recommended. If

mounting to two studs on 16" centers, leave an open stud in center. Wall plate may be mounted up to 6" (152 mm)

off-centerasshownin figure 1.3.

Skip to step 2 on page 7.

• Installermustverify that the supporting surface will safely support the combined load oftheequipmentandall attached

hardwareandcomponents.

• Tightenwoodscrews so that wall plate is firmly attached, butdonotovertighten. Overtightening can damage the

screws,greatly reducing their holdingpower.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is

highlyrecommended.

• Hardwareprovided is for attachment of mount throughstandardthickness drywall or plaster into woodstuds.Installers

areresponsible to provide hardwarefor other types ofmountingsituations.

WARNING

2.5"

(64 mm)

fig. 1.4

STUD

6 of 24 ISSUED: 01-13-06 SHEET #: 202-9030-2 01-30-06

Installation to Solid Concrete or Cinder Block

1Make sure that wall plate (AA) is level, use it as a

template to mark four mountingholes. The top

mountingholeshouldbe2.5"abovethe desired screen

center as shown in figure 1.1 on page 4. Drill four 1/4"

(6 mm) dia. holes to a minimum depth of 2.5" (64 mm).

Insert anchors (EE) in holes flush with wall as shown

(right).Placewallplate over anchors and secure with

#14 x 2.5" screws (DD). Level, then tighten all

fasteners.

NOTE: Six holes and six sets of fasteners are required

whenmounting the wall plate for equipment weighing

greaterthan200lbs.

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid

part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifica-

tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to

avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Makesurethat the supporting surface will safely support the combined load of the equipment and all attached hard-

wareand components.

WARNING

CUTAWAY VIEW

INCORRECT

concrete

surface

Drill holes and insert anchors (EE).

CORRECT

Place plate (AA)over anchors (EE) and secure with screws (DD).

Tighten all fasteners.

wall

plate

plaster/

drywall

concrete wall plate concrete

plaster/

drywall

• Always attach concrete anchorsdirectly to load-

bearingconcrete.

• Neverattach concrete anchorsto concrete covered

withplaster, drywall, or other finishingmaterial.If

mountingto concrete surfaces coveredwitha finishing

surfaceis unavoidable, the finishing surfacemustbe

counterbored asshown below. Be sureconcrete

anchorsdo not pull away from concrete whentighten-

ing screws. If plaster/drywall is thicker than 5/8",

custom fasteners must be supplied by installer.

WARNING

• Tighten screws so that wall plate is firmly attached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

WARNING

solid concrete cinder block

7 of 24 ISSUED: 01-13-06 SHEET #: 202-9030-2 01-30-06

fig 2.1 Note: "X"dimensions should be equal.

Notes:

• Alwaysuse multi-washers when attaching

tilt brackets (BB and CC) to your screen.

• Use the corresponding hole in the multi-

washer that matches your screw size as

showninfigure2.2.

• Spacers maynotbeused, depending upon

the type of screen.

• Tightenscrewsso adapter brackets are firmly

attached. Do not tighten with excessive force.

Overtighteningcancause stress damage to screws,

greatlyreducing their holding powerandpossibly

causingscrewheads to become detached. Tighten to

40 in. • lb (4.5 N.M.) maximum torque.

• If screws don't get three complete turns in the screen

inserts or if screws bottom out and bracket is still not

tightly secured, damage may occur to screen or

productmayfail.

WARNING

Installing Tilt Brackets

CENTERBRACKETS

VERTICALLYON

BACKOFSCREEN

Refer to Screen Compatibility Chart to determine the proper fasteners to use.

To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place

screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached.

Place tilt brackets (BB and CC) on back of screen.Align to holes, and center on back of screen as shown in figure

2.1. Attach the tilt brackets to the back of the screen using the appropriate combination of screws, multi-washers,

and spacers as shown in figure 2.3. Note: Be sure to attach tilt brackets with knobs facing outward as in figure 2.1.

Note: Top and bottom mounting holes must be used for attaching brackets. Middle holes should also be used where

thefasteners and screens allow.

Verify that all holes areproperlyaligned, and then tighten screws using a phillipsscrewdriverorsecuritywrench(FF)

dependingon the fastenersused.

MEDIUMHOLEFORM5SCREWS

SMALLHOLEFORM4SCREWS

LARGEHOLEFORM6SCREWS

fig. 2.2

MULTI-

WASHER

SPACER

MULTI-WASHER

SCREW

fig 2.3

Note: Slots in ST680, ST 680P, ST680-S, and

ST680P-S are wider and require the useofthe

M8 washer I.D. 8.9 mm.

8 of 24 ISSUED: 01-13-06 SHEET #: 202-9030-2 01-30-06

Mounting and Removing Flat Panel Screen

Hook tilt brackets (BB andCC) onto wall plate (AA).

Then slowly swing screen in as shown. Turnsafety/

security screws, using phillips screw driver or security

allen wrench (FF), clockwise at least six times to

preventscreenfrombeingremovedasshownindetail1.

offigure3.1.

Screen can be adjusted horizontally if desired as

showninfigure3.2.

Note: To lock the screen down, tighten screws to wall

plateusing aphillips headscrewdriver orsecurty allen

wrench (FF) as shown in detail 1.

Toremovescreenfrommount,loosenscrews,swing

screenawayfrommount,andliftscreenoffofmount.

SmartMountisatrademarkandPeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.

Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.

Unlock tilt position by loosening IncreLok™ tilt

locking screws on both tilt brackets.Adjust

tension knobs shown in detail 2 to desired

tension, balancing your screen size and weight.

Push or pull from top or bottom of screen to

adjust tilt as shown in figure 4.1. The tilt can be

adjusted to a maximum of 15° forward or 5°

backward.

Note: To lock the screen into the desired tilt

position, use locator hole to find tilt position.

Tighten IncreLok™ tilt locking screws on both

tilt brackets as shown in figure 4.1 and detail 2.

Adjusting the Tilt Angle of the Flat Panel Screen

• Becarefulnot to pinch fingers when pushing screen

fromthebottom.

CAUTION

• Do not tighten screws with excessive force.

Overtighteningcan cause damageto mount. Tighten

screws to 40 in. • lb (4.5 N.M.) maximum torque.

CAUTION

BB and CC

DETAIL 1

• Always use an assistant or mechanical lifting equip-

ment to safely lift and position the plasma television.

WARNING

DETAIL 2 fig 4.1

SAFETY/

SECURITY

SCREW

IncreLok™TILT

LOCKING

SCREW

LOCATOR

HOLE

TENSION

KNOB

fig 3.1

fig 3.2

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 01-13-06 SHEET #: 202-9030-2 01-30-06

Instalación y montaje:

Soportes universales inclinables de pared

Características:

• Para pantallas planas

• Inclinación de un toque para colocar y ajustar la pantalla sin esfuerzo

• El diseño ultra delgado sujeta la pantalla plana contra la pared

• Posiciones inclinadas trabables Increlok™ para ajustes específicos de

inclinación en incrementos de 5º

• Viene en negro o plateado

• Modelos con y sin tornillos de seguridad

Product is UL rated for screen size range and load capacity per chart below Este producto está

clasificado por Underwriters Laboratories (UL) para utilizarse con pantallas dentro de las gamas de tamaños y

de la capacidad de soportar carga ____ según lo indicado en la tabla que aparece continuación.

Nº de modelo Gama de tamaños Capacidad máxima de

de la pantalla soportar carga según UL:

ST640,ST640P, 23"-46" 150 lb (68 kg)

ST640-S, ST 640P-S,

RTFPT-220,RTFPT-220S

D-FPT-220,D-FPT-220S

ST650,ST650P, 32"-50" 175 lb (79 kg)

ST650-S, ST 650P-S

ST660,ST660P, 32"-60" 200 lb (91 kg)

ST660-S, ST 660P-S,

RTFPT2-320,RTFPT2-320S

D-FPT2-320,D-FPT-320S

ST670,ST670P, 42"-71" 250 lb (113 kg)

ST670-S, ST 670P-S

ST680,ST680P, 61"-102" 350 lb (159 kg)

ST680-S, ST 680P-S

10 of 24 ISSUED: 01-13-06 SHEET #: 202-9030-2 01-30-06

Nota:Read entire instruction sheet before you start installation and assembly.Lea toda la hoja de instrucciones antes de

iniciar la instalación y el montaje.

Herramientas necesarias para el montaje

•localizadordemontantes(serecomiendausarelde “borde a borde”)

•destornilladorphillips

•taladro

•broca de 1/4" para pared de concreto y de bloques de hormigón de escorias

•broca de 1/2" para pared con montantes de metal

•broca de 5/32" para pared con montantes de metal o madera

•nivel

Contenido

Lista de piezas ...................................................................................................................................................................11

Instalaciónen unapared conmontantes demaderadobles................................................................................................12

Instalaciónen una paredconmontantes de madera triples ................................................................................................13

Instalación en una pared de concreto macizo o de bloques de hormigón de escorias ........................................................14

Instalacióndelossoportesadaptadores .............................................................................................................................15

Instalación de la pantalla plana en la placa de apoyo .........................................................................................................16

Paraatenciónalcliente,llame al (800) 729-0307 ó (708) 865-8870.

Accesorios

•Juegode4 piezas de fijaciones para montantes de metal (ACC 415) (montante de metal no evaluado por UL)

•Juegode2 piezas de fijaciones para montantes de metal (ACC 215) (montante de metal no evaluado por UL)

• No comience la instalación de su producto Peerless sin antes leer y comprender las instrucciones y los avisos de

precaución contenidos en esta hoja de instalación.If you have any questions regarding any of the instructions or

warnings,please call Peerless customer care at 1-800-729-0307.Ante cualquier duda respecto a las instrucciones o

avisosdeprecaución,llameal departamento de servicio al cliente de Peerless al 1-800-729-0307.

• Este producto debe instalarlo una persona con buenas aptitudes mecánicas, experiencia en la construcción básica

de edificios y una comprensión total de estas instrucciones.

• Asegúrese de que la superficie de apoyo sea capaz de soportar firmemente la carga combinada del equipo y todos

los herrajes y componentes.

• Nuncasobrepasela capacidad máxima de soportar carga aceptada por Underwriters Laboratories.Seepageone.

Vea la página uno.

• Si la instalación va a hacerla en paredes con montantes de madera, asegúrese de que los tornillos de montaje estén

anclados en el centro de los montantes.Use of an “edge to edge” stud finder is highly recommended. Se recomienda

usarunlocalizadordemontantesde“bordeaborde”.

• Siempre solicite la ayuda de un asistente o utilice un equipo de izar mecánico para levantar y colocar el equipo con

másseguridad.

• Aprietelos tornillos firmemente, pero no en exceso.Overtighteningcan damage the items, greatly reducing their

holdingpower.Elapriete excesivo puede dañar los artículos, reduciendoenormementesufuerza de fijación.

ADVERTENCIA

This manual suits for next models

Table of contents

Languages:

Other PEERLESS Rack & Stand manuals

PEERLESS

PEERLESS SGLS01 User manual

PEERLESS

PEERLESS SOLID POINT PLCM 1 Instruction Manual

PEERLESS

PEERLESS Mobile Videowall Trolley PDVWM 2x2 46 55 L Guide

PEERLESS

PEERLESS SmartMount SP740P Guide

PEERLESS

PEERLESS VPM 25-J Guide

PEERLESS

PEERLESS Solid-Point PLCM UN1 Guide

PEERLESS

PEERLESS IM740P Guide

PEERLESS

PEERLESS DS-VW650 Guide

PEERLESS

PEERLESS JMWS 30 Guide

PEERLESS

PEERLESS PANA-85WM Guide

PEERLESS

PEERLESS ACC517 Guide

PEERLESS

PEERLESS Vision Point LCFS 100 Guide

PEERLESS

PEERLESS PARAMOUNT PF640 Guide

PEERLESS

PEERLESS RTLA-100 Guide

PEERLESS

PEERLESS LWB375 Guide

PEERLESS

PEERLESS PARAMOUNT PA730 Guide

PEERLESS

PEERLESS SF630-AB Guide

PEERLESS

PEERLESS SlimLine MOWV241/BK User manual

PEERLESS

PEERLESS SP730P Guide

PEERLESS

PEERLESS DS415 Guide

PEERLESS

PEERLESS Slimline OP-LWB 530 Guide

PEERLESS

PEERLESS DST940 Guide

PEERLESS

PEERLESS SPK 811W User manual

PEERLESS

PEERLESS ACC-V800X Guide

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 