Panasonic AWE300S - SEPERATE CAMERA User manual
OPERATING INSTRUCTIONS
Before attempting to connect, operate or adjust this product, please
read these instructions completely.
1/3-inch Camera With Separate Head
Model AW- P
FOCUS
LOCK
2
indicates safety information.
CAUTION
RISK OF ELECTRIC SHOCK
O NOT OPEN
CAUT ON: TO REDUCE THE R SK OF ELECTR C SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERV CEABLE PARTS NS DE.
REFER TO SERV C NG TO QUAL F ED SERV CE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle,
is intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (service)
instructions in the literature accompanying the appliance.
WARNING:
TO RE UCE THE RISK OF FIRE OR SHOCK HAZAR , O NOT
EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
CAUTION:
TO RE UCE THE RISK OF FIRE OR SHOCK HAZAR AN ANNOYING
INTERFERENCE, USE THE RECOMMEN E ACCESSORIES ONLY.
FCC Note:
This device complies with Part 15 of the FCC Rules. To assure continued
compliance follow the attached installation instructions and do not make any
unauthorized modifications.
This equipment has been tested and found to comply with the limits for a class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
3
Contents
Introduction. . . . . . . . . . . . . . . . . . . . . . . 4
Features. . . . . . . . . . . . . . . . . . . . . . . . . . 4
Special Notes on Operation. . . . . . . . . . 5
Precautions . . . . . . . . . . . . . . . . . . . . . . . 6
Parts and Their Functions . . . . . . . . . . . 7
$Main unit . . . . . . . . . . . . . . . . . . . . . . 7
$Camera head unit . . . . . . . . . . . . . . . 9
Installation. . . . . . . . . . . . . . . . . . . . . . . 10
$Attaching the lens . . . . . . . . . . . . . . 10
$nstallation on a camera stand
(tripod, etc.) . . . . . . . . . . . . . . . . . . . 10
System Configuration (Connections)
. . . 11
$Connecting equipment with a
composite video input connector. . . 11
$Connecting a remote control unit
(RCU) . . . . . . . . . . . . . . . . . . . . . . . 12
$Connecting a remote control box
(RCB) . . . . . . . . . . . . . . . . . . . . . . . 13
$Connecting multiple cameras
(achieving genlock) . . . . . . . . . . . . . 14
$Connections for exercising control
from a computer . . . . . . . . . . . . . . . 15
$Reference: Model numbers of related
equipment . . . . . . . . . . . . . . . . . . . . 16
Operating Mode Selection . . . . . . . . . . 17
$
How to select the operating mode
. . 18
Operating Procedures . . . . . . . . . . . . . 19
Adjustments . . . . . . . . . . . . . . . . . . . . . 20
$Flange back adjustment . . . . . . . . . 20
$White balance adjustment. . . . . . . . 21
$Black balance adjustment . . . . . . . . 23
$Black level (total pedestal)
adjustment. . . . . . . . . . . . . . . . . . . . 24
$Genlock adjustment. . . . . . . . . . . . . 25
Menu Item Settings and Changes . . . . 27
$Setting the menu items . . . . . . . . . . 27
$
Halogen light, fluorescent light and
outdoor mode sub-menu screens
. . . 29
$User mode sub-menu screens . . . . 35
Returning to Initial Settings. . . . . . . . . 42
$nitial settings (factory settings). . . . 43
Outline rawings . . . . . . . . . . . . . . . . . 45
$Main unit . . . . . . . . . . . . . . . . . . . . . 45
$Camera head unit . . . . . . . . . . . . . . 45
Specifications . . . . . . . . . . . . . . . . . . . . 46
$Accessories. . . . . . . . . . . . . . . . . . . 47
4
Introduction
OFeaturing digital video signal processing, this 1/3-inch 3-CCD system color camera with
its separate head achieves a high picture quality and high reliability as well as many and
varied functions despite its compact size and light weight.
OThe head is separate which means that it can easily be mounted on a microscope (C
mount), for instance.
OUsing a menu screen format, the camera’s shooting conditions and functions can easily
be set and changed.
OThe camera can be connected to a peripheral unit such as an RCB or RCU for
expanding the capabilities of the system to suit the intended applications.
OA wide range of applications can be supported by installing optional cards.
Features
High picture quality, high reliability, many and varied functions, a compact size and
light weight achieved by incorporating digital video signal processing
OResolution: 800 lines (high band DTL ON), S/N ratio: 62 dB (DNR ON)
OMinimum illumination: 1.5 lux (f/1.4 ‘night eye’ mode)
Many and varied functions despite compact size
OSetting of camera parameters using menu screens enabled
OAuto functions such as ATW, ELC and AGC incorporated
OCCD readout (field, frame) switching supported
The vertical resolution can be improved by switching to the frame mode, and this is
useful for capturing still images and other kinds of image processing.
OSynchro scan function provided to reduce horizontal line noise when computer screens
are shot
OFunctions for controlling camera by computer incorporated
OExtension of cable (standard length of 3 meters) between head unit and main unit up to
10 meters possible
Faithful image reproduction assured by many compensation circuits
OEven areas with dark colors reproduced clearly by chroma detail enhancement
ONatural detail enhancement enabled even for dark areas by dark detail circuit
ONatural dynamic range reproduced by digital highlight chroma
OFaithful reproduction of colors enabled by digital color matrix
Full spectrum of video productions supported
OConditions optimally suited to each application selectable from 4 operation modes
(halogen light mode, fluorescent light mode, outdoor mode and user mode)
OSMPTE color bar display provided
ORemote control enabled by RCU or RCB
5
Special Notes on Operation
OTurn the power off before connecting or disconnecting cables.
OConnection or disconnection of any studio cable, RCB cable or other cable to any unit of
equipment must be performed while power is off.
While the camera is in automatic mode:
OShooting of bright objects in ELC operation mode may result in a smeared picture
unique to the CCD.
OThe ATW function under fluorescent illumination can adversely change the white
balance.
6
Precautions
ODo not attempt to disassemble the camera, Remote Control Unit (RCU) or other units.
n order to prevent electric shock, do not remove screws or covers. There are no user-
serviceable parts inside.
ODo not mishandle the camera. Avoid striking, shaking, etc. The camera contains
precision components which could be damaged by improper handling or storage.
ODo not let the lens remain uncovered when the camera is not in use. f the lens is not
installed, do not leave the lens mount hole uncovered.
ODo not touch the surface of the lens or prism.
ODo not use strong or abrasive detergents when cleaning the camera body.
ODo not aim the camera toward the sun, irrespective of whether it is turned on or not.
ODo not expose the camera or Remote Control Unit (RCU) to rain or moisture, and do not
try to operate the equipment in wet conditions. Do not operate the camera or RCU if it is
wet.
ODo not operate the camera or Remote Control Unit (RCU) outdoors during a thunder
storm.
ODo not use the camera where it will be subject to high temperatures or high humidity.
ODo not leave the camera and Remote Control Unit (RCU) turned on when not in use. Do
not unnecessarily turn the camera power on and off repeatedly. Do not block the
ventilation slots.
ORefer any servicing to qualified service personnel.
OHandle the camera with care.
OPlace the lens cap on the lens when the camera is not in use. f the lens is not installed,
protect the surface of the prism by placing the body cap over the lens mount hole.
OUse a mild blower or lens cleaning tissue designed for coated lenses to clean the
surface of the lens or prism if it requires cleaning.
OUse a dry cloth to clean the camera if it is dirty. f the dirt is hard to remove, use mild
detergent and wipe gently.
OUse caution when operating the camera near spot lights or bright lights, as well as any
objects and surfaces which may reflect light.
Of the camera or RCU gets wet, turn the power off immediately and have the unit
checked by an authorized service facility.
OFollow normal safety precautions to avoid personal injury.
OUse the camera in an environment where the temperature is within 14°F to 113°F
(–10°C to +45°C), and the relative humidity is within 30 % to 90 %.
OAlways turn the power off when the camera is not going to be used. Operate the
camera and RCU only when there is adequate ventilation.
OOperating a wireless device that generates powerful radio waves near the camera may
adversely affect the output images.
7
$Main unit
1
OPT ON CARD
MENU
TEM / AWC
YES / ASC
+
-
NO / BAR
V DEO OUT
G / L N
/ F REMOTE
R S
DC12V N
6=
;
2
<
8
7
9
:
3
4
5
Parts and Their Functions
1Cable connector
This is used to connect the camera to the camera head unit using a cable.
2MENU switch [MENU (t)]
The menu will appear on the screen when this switch is pressed for about 5 seconds.
When it is pressed while a menu is displayed, the menu item immediately above is
selected.
3ITEM/AWC switch [ITEM/AWC (y)]
When this switch is pressed while a menu is displayed, the menu item immediately
below is selected. While a menu is not displayed (when the camera is in the shooting
mode), it serves as the automatic white balance control (AWC) switch.
4YES/ABC switch [YES/ABC (+)]
When this switch is pressed while a menu is displayed, the sub-menu of a menu item
appears on the screen. When it is pressed while a sub-menu is displayed, the higher of
the two settings shown is selected. While a menu is not displayed, it serves as the
automatic black balance control (ABC) switch.
5NO/BAR switch [NO/BAR (–)]
When this switch is pressed while the main menu is displayed, the next item down can
be selected. When it is pressed while a sub-menu is displayed, the lower of the two
settings shown is selected. When it is pressed for about 5 seconds while a menu is not
displayed, the color bar signals and camera (shooting mode) are switched.
8
Parts and Their Functions
6Video output connector [VI EO OUT]
The composite video signals are output from this connector.
(1 V [p-p], 75 Ω, BNC connector)
7Iris connector [IRIS]
This is the standard input connector of the lens which comes with an auto iris function.
8Interface/remote connector [I/F REMOTE]
This is used to connect the remote control unit (RCU: WV-RC700A or WV-RC550),
remote control box (RCB: WV-CB700A), etc.
The AW-CA50A26 RCU cable is required to connect the WV-RC700A or WV-RC550.
The AW-CA50T10 RCB cable is required to connect the WV-CB700A.
9Power LE
This lights up red when DC power is supplied to the DC 12V input socket :.
:C 12V input socket [ C 12V IN]
The DC 12 V power supply (2 A or above) is connected here using the AW-CA4T1 DC
power cable.
;Cable clamp
This clamps the AW-CA4T1 DC power cable which has been connected to the DC 12V
input socket :to prevent the cable from becoming disconnected.
<Genlock input connector [G/L IN]
The external sync (black burst) signals are supplied to this connector to achieve genlock
with the camera.
=Option card slot
This slot is used by the option cards.
For further details, refer to the operating instructions of the option card concerned.
9
?> @
AA
FOCUS
LOCK
FOCUS
LOCK
$Camera head unit
Parts and Their Functions
>Lens mount
A 1/3-inch C mount lens or microscope adapter, etc. is attached here.
?Flange back adjust screw [FOCUS/LOCK]
When the flange back needs to be adjusted, remove the cap, loosen the LOCK screw,
and adjust by turning the FOCUS screw. (Adjustment range: ±0.2 mm)
Upon completion of the adjustment, re-tighten the LOCK screw.
@Cable connector
This is used to connect the head unit to the main unit using a cable.
ACamera mounting adapter
(mounting screw holes: M2.6a10, spring washers provided)
This is used to secure the head unit when it is to be installed on a wall or ceiling or a
tripod is to be used. The head unit can be mounted on the top or bottom surface.
Other manuals for AWE300S - SEPERATE CAMERA
1
This manual suits for next models
1
Table of contents
Other Panasonic Security Camera manuals
Panasonic
Panasonic AW-UE70WP User manual
Panasonic
Panasonic AWHE50HN - HD INTEGRATED CAMERA User manual
Panasonic
Panasonic BL-C140 User manual
Panasonic
Panasonic WV-SW175 User manual
Panasonic
Panasonic KX-HCM280A User manual
Panasonic
Panasonic WV-CS400 User manual
Panasonic
Panasonic WVCS554 - COLOR CAMERA User manual
Panasonic
Panasonic WV-NW960 series User manual
Panasonic
Panasonic BB-HCM381A - Network Camera User manual
Panasonic
Panasonic WVNM100 - NETWORK COLOR CAMERA User manual
Panasonic
Panasonic WV-NW484S - i-Pro Network Camera User manual
Panasonic
Panasonic WV-SW458 User manual
Panasonic
Panasonic A34 User manual
Panasonic
Panasonic WV-NF284 - i-Pro Network Camera User manual
Panasonic
Panasonic WV-CPR460 User manual
Panasonic
Panasonic WV-CF364E User manual
Panasonic
Panasonic AKHC910 - 1080I CAMERA User manual
Panasonic
Panasonic HomeHawk WINDOW User manual
Panasonic
Panasonic WV-CP240EX User manual
Panasonic
Panasonic AW-UE80KP User manual
