Panasonic WV-Q126A User manual

Before attempting to connect or operate this product,

please read these instructions carefully and save this manual for future use.

The model number is abbreviated in some descriptions in this manual.

Operating Instructions

Included Installation Instructions

Ceiling Mount Bracket

Model No. WV-Q126A

FRANÇAIS DEUTSCH ENGLISHESPAÑOLITALIANO

РУССКИЙ

Contents

Features......................................................................................................................................... 3

Precautions ................................................................................................................................... 3

Precautions for installation............................................................................................................ 4

Major Operating Controls..............................................................................................................6

Installations ................................................................................................................................... 7

Specifications.............................................................................................................................. 15

Standard accessories.................................................................................................................. 15

This ceiling mount bracket is exclusively

designed to mount the Camera, on a ceiling.

Refer to the catalog or operating instructions of

the camera for further information about the

compatible models.

This bracket can be used for an area with weak

pull-out strength such as plasterboard in a

double ceiling.

This bracket is an embedded type to reduce

the exposed portion of the camera body.

Features

Precautions

Refer installation work to the dealer.

Installation work requires technique and experi-

ences.

Failure to observe this may cause fire, electric

shock, injury, or damage to the product.

Be sure to consult the dealer.

Avoid installing this bracket in the loca-

tions where salt damage occurs or corro-

sive gas is produced.

Otherwise, the mounting portions will deterio-

rate and accidents such as a fall of this product

may occur.

The screws and bolts must be tightened to

the specified torque.

Loosening of mounting screws or bolts may

cause a fall of the product resulting in injury or

accidents.

Do not use this bracket except with suit-

able cameras

Failure to observe this may cause a drop result-

ing in injury.

Select an installation area that can sup-

port the total weight.

Selecting an inappropriate installation surface

may cause this product to fall down or topple

over, resulting in injury or accidents.

Installation work shall be started after sufficient

reinforcement.

Do not rub the edges of metal parts with

your hand.

Strong rubbing may cause injury.

Periodic inspections shall be conducted.

Rust on the metal parts or screws may cause a

fall of the product resulting in injury or acci-

dents.

Consult the dealer for the inspections.

The measures of protection against a fall

of this product shall be taken.

Failure to observe this may cause a drop result-

ing in injury or accidents.

Be sure to install the safety wire.

The exclusively designed mount bracket

shall be used.

Failure to observe this may cause a drop result-

ing in injury or accidents.

Use the exclusively designed mount bracket for

installation.

Do not install this product in locations

subject to vibration.

Loosening of mounting screws or bolts may

cause a fall of the product resulting in injury or

accidents.

Do not strike or give a strong shock to this

product.

Failure to observe this may cause fire or injury.

Install this product in a location high

enough to avoid people and objects from

bumping the product.

Failure to observe this may cause injury.

Do not hang down from this product or

use this product as a pedestal.

Failure to observe this may cause a drop result-

ing in accidents.

ENGLISH

Precautions for installation

Panasonic assumes no responsibility for injuries or property damage resulting from fail-

ures arising out of improper installation or operation inconsistent with this documenta-

tion.

The installation should comply with local electrical code.

This product is designed to be used indoors.

This product is not operable outdoors.

Do not expose this product to direct sunlight for hours and do not install the product near a heater

or an air conditioner.

Otherwise, it may cause deformation, discoloration and malfunction. Keep this product away from

water and moisture.

Installation area for this product

Make sure that the installation area is strong enough to hold the total weight of the camera•

assembly before installation.

The installation area shall have 210 mm {8-9/32 inches} or more space behind the ceiling.•

The thickness of the ceiling board for installation can range between 9 mm {3/8 inches} and•

40 mm {1-9/16 inches}.

Do not place this product in the following places:

Locations where it may get wet from rain or water splash (including under the eaves, etc.)•

Locations where a chemical agent is used such as a swimming pool•

Locations subject to moisture or oil smoke such as a kitchen•

Locations that have a specific environment that is subject to an inflammable atmosphere or sol-•

vents

Locations where a radiation, an X-ray, a strong radio wave or a strong magnetic field is gener-•

ated

Locations where corrosive gas is produced, locations where it may be damaged by briny air such•

as seashores

Locations where the temperature is not within the specified range (–10 °C to +55 °C {14 °F to•

131 °F})

Locations subject to vibrations, such as on vehicles, marine vessels, or above product lines (This•

product is not designed for onvehicle use.)

Locations subject to condensation as the result of severe changes in temperature•

210 mm {8-9/32 inches}

or more

Ceiling board: between 9 mm {3/8 inches}

and 40 mm {1-9/16 inches}

Mounting method for this product

This product is designed to be used as a pendant mount camera. If the product is mounted on a

desktop or at a slant, it may not work correctly and its lifetime may be shortened.

Procure anchor bolts separately.

An anchor bolt for mounting the bracket on a ceiling is not supplied with the ceiling mount bracket.

Prepare them according to the material and strength of the area where the product is to be

installed.

Anchor bolt: M10, recommended•

Minimum pull-out strength:• Make sure that more than 5 times of the total weight including the

camera body can be supported.

Screw tightening

The screws and bolts must be tightened with an appropriate tightening torque according to the•

material and strength of the installation area.

Do not use an impact driver. Use of an impact driver may damage the screws or cause tightening•

excessively.

When a screw is tightened, make the screw at a right angle to the surface. After tightening the•

screws or bolts, perform checks to ensure that the tightening is sufficient enough so that there is

no movement or looseness.

Make sure to remove this product if it will no longer be used.

Major Operating Controls

Mounting chassis

Decorative cover (main)

Decorative cover (sub)

Camera mounting

stage

Paper gauge

Ceiling board fixing screw (x4)

Tie wrap (for cable installation)

(x4)

Ceiling board fixing bracket (x4)

Ceiling board

Roof space

Safety wire angle (accessory)

Safety wire (accessory)

Ceiling mount bracket

Decorative cover

Camera

Installations

Be sure to read "Precautions" (☞page 3) and "Precautions for installation" (☞page 4) before instal-

lation. Read the operating instructions for the camera to be installed as well.

Step 1

Put Template A (accessory) against the ceiling and

make the ø220 mm {8-21/32 inches} hole.

Step 2

Install two anchor bolts (M10 recommended) into the ceiling.

One anchor is used for securing the mounting chassis, and the other anchor is used for connecting

the safety wire.

Determine the anchor boltq (for securing the mounting chassis) length by use of Template B

(accessory).

Position the nut by use of Template B (accessory)w and mount the nut. (The distance between the

bottom surfaces of the ceiling board and nut shall be 183 mm {7-7/32 inches}.)

Important:

The pull-out strength of the anchor bolt shall be more than 5 times of the total weight of the•

installed devices (including the camera body, ceiling mount bracket, anchor bolts, and all other

parts).

When the existing anchor bolt is used as an anchor bolt for connecting the safety wire, make•

sure that the distance between the anchor bolt and camera mounting position is 1 m {3.28 feet}

or less.

Anchor bolt (for connecting

the safety wire)

wMount a nut

qDetermine the anchor bolt length

Install the anchor bolt in the center of the hole

183 mm {7-7/32 inches}

Template B

Ceiling board

Anchor bolt (for securing

the mounting chassis)

Template A

ø220 mm

{8-21/32 inches}

Ceiling face

Note:

When the existing anchor bolt that has been•

installed is used for connecting the safety

wire, the use of 2 spacer nuts is helpful.

Step 4

Attach the paper gauge (accessory) to the

camera mounting stage.

Fold the double-sided tape side of theq

paper gauge at a right angle as shown in

the drawing.

Peel off the backing from the double-sidedw

tape of the paper gauge.

Spacer nuts

Safety wire

Safety wire angle

Spacer nuts

Existing anchor bolt

Paper gauge

Folding line

Double-sided tape

Step 3

Secure the safety wire angle (accessory) to the

anchor bolt (for connecting the safety wire),

and connect the safety wire (accessory).

Mount a nut so that the safety wire angle isq

secured on the anchor bolt.

Disconnect the safety wire from the safetyw

wire angle.

Engage the face markede qwith the anchor

bolt.

Bend the face markedr w.

Connect the safety wire to the safety wiret

angle again.

Engage the nut from beneath, and securey

the safety wire angle with top and bottom

nuts.

Engage another nut from beneath to tightenu

and secure the nut that was engaged from

beneath in yin a double nut fashion.

Upper side

Lower

side

Safety wire

eInsert

w Disconnect

rBend

Mark w

Mark q

tConnect

Safety wire angle

Anchor bolt

* The nut is omitted in the illustration above.

Turn this bracket sideways as shown in thee

following drawing, and attach the paper

gauge to the camera mounting stage.

Attach the paper gauge so that it passes

through the slit shown in the following draw-

ing.

Step 5

Pass the cables from the ceiling through theq

loop of the tie wrap attached to the mount

bracket in advance. Tie wraps used for

passing the cables vary with models. The

cable passing position is in the following

drawing.

Models with use of camera mount bracket

(accessory to the camera): tie wrap A or tie

wrap C in the following drawing

Models with use of base unit (component

of the camera): tie wrap B or tie wrap D in

the following drawing

Paper gauge

Paper gauge attaching position

Slit

bAttach the

paper gauge

Attach the safety wire to the mountingw

chassis as shown in the following drawing.

Insert the mounting chassis into the hole

made in Step 1, and put them into the roof

space.

At this moment, the logo direction at

mounting the decorative cover finally can

be aligned with the III direction of the

mounting chassis.

Therefore, if you care about the brand logo

direction, determine the direction using the

III direction.

Direction of brand logo

Direction of

brand logo

Direction of

brand logo

Direction of

brand logo

Tie wrap A

Tie wrap B

Tie wrap D

Tie wrap C

Roof space

Ceiling board

Safety wire

(accessory)

Mounting

chassis

Cables

Pass the loop

through the tip of

the safety wire.

Step 7

Prepare the cables.

Run the cables from the space of the mounting

chassis. The wiring image with the bracket

mounted on the ceiling is described below. Be

careful to prevent the cables from being caught

on the ceiling board fixing bracket or others.

Ceiling board fixing screw (x4)

(mounting chassis outside)

Recommended tightening torque:

0.78 N·m {0.58 lbf·ft}

Step 6

Secure the mounting chassis to the ceiling

board with the ceiling board fixing screws (4

positions, screws with label q).

Engage the top of the mounting chassisq

with the anchor bolt (for securing the

mounting chassis).

Secure the mounting chassis by turning thew

ceiling board fixing screws clockwise when

viewing it from beneath. Turning the ceiling

board fixing screws clockwise provides ceil-

ing board tightening between the bottom of

the mounting chassis and ceiling board fix-

ing bracket resulting in mounting chassis

securing.

Recommended tightening torque:

0.78 N·m {0.58 lbf·ft}

Important:

When securing the mounting chassis on•

the ceiling, make sure that the 4 ceiling

board fixing brackets are open as shown in

the figure e.

Secure the top of the mounting chassise

with double nuts.

Anchor bolt (for securing the

mounting chassis)

Ceiling board fixing

bracket (x4)

Ceiling board

fixing screw

(x4)

Double nuts

Table of contents

Languages:

Other Panasonic Camera Accessories manuals

Panasonic

Panasonic DMW-DCC6 User manual

Panasonic

Panasonic WV-Q173 User manual

Panasonic

Panasonic WV-Q122E User manual

Panasonic

Panasonic H-H014A User manual

Panasonic

Panasonic AJ-VF15BP User manual

Panasonic

Panasonic WVPH10 - CL CAMERA ACCESS User manual

Panasonic

Panasonic FL360 - DMW - Hot-shoe clip-on Flash User manual

Panasonic

Panasonic VIDEOALARM PODV7CWNS/PODV7CPNS User manual

Panasonic

Panasonic HHR150AA User manual

Panasonic

Panasonic AS09A51 Instruction Manual

Panasonic

Panasonic WJ-MPU855 User manual

Panasonic

Panasonic HFS1442A User manual

Panasonic

Panasonic WV-Q103A User manual

Panasonic

Panasonic AU-VCVF10G User manual

Panasonic

Panasonic AG-CVF15G User manual

Panasonic

Panasonic BB-HGW700A - Network Camera Router User manual

Panasonic

Panasonic AJHVF21G - HD EVF - MULTI-LANG User manual

Panasonic

Panasonic AJ-YA600P User manual

Panasonic

Panasonic Lumix H-FS014045 User manual

Panasonic

Panasonic WV-QCL500-S User manual

Panasonic

Panasonic AJ-RC905EN User manual

Panasonic

Panasonic HHR330APH User manual

Panasonic

Panasonic LC-XC1228AP User manual

Panasonic

Panasonic VariCam AU-VSHL1G User manual

Popular Camera Accessories manuals by other brands

Viltrox

Viltrox EF-NEX Mount instructions

Calumet

Calumet 7100 Series CK7114 operating instructions

Ropox

Ropox 4Single Series User manual and installation instructions

Cambo

Cambo Wide DS Digital Series Main operating instructions

Samsung

Samsung SHG-120 Specification sheet

Ryobi

Ryobi BPL-1820 Owner's operating manual

Aegis

Aegis ABL-36020P user manual

Pentax

Pentax Data Back Fc operating manual

Fantasea

Fantasea EyeGrabber F Series instruction manual

Honeywell

Honeywell HDZ20HD user manual

EGO

EGO BA1400T Operator's manual

Sima

Sima SRW-62 user guide

Shape

Shape A7SSMKIT Assembly manual

Slide Kamera

Slide Kamera HST-2 user manual

Power works

Power works 2902613 Original instructions

SES

SES SE-2047-2 user manual

Olympus

Olympus PT-EP05L instruction manual

Starlite

Starlite OctoDome nxt instructions