Panasonic FV-07VBA1 User manual

INSTALLATION FOR FV-07VBA1 (WALL MOUNTING)

Install the fan at least 1.5m (5 feet) above the floor.

The motor/grille assembly FV-07VBB1 must be installed with housing can FV-07VBA1 that

is marked on the carton to indicate the suitability with this model. Other motor/grille

assembly can not be substituted.

(ST4.2X20) 12

1. Affix the fan housing to joist with 3 long

screws (ST4.2X20) by affixing first 1 screw

2. Install the v duct and secure it entilation

with a clamp and seal it with mastic or

approved foil tape. A 4 inch circular duct is

needed to connect to the relevant part of

adaptor. (Fig.2) Fig.1

Fig.2

Fig.3

INSTALLATION FOR FV-07VBA1(JOIST MOUNTING)

3 Long screws

(ST4.2X20)

Joist

Fan

housing

Clamps

Key hole

Clamps

Tongue

Adaptor

Ventilation duct

Mastic or approved

foil tape

Fan housing

Conduit

Junction

box

Earth ground

to green

Neutral to white

Live to black

Wire nut

ADAP

APTOR

JUNCTION

BOX

JUNCTION

BOX

Thermally - protected

(114 Fuse in motor)

Thermally - protected

(114 Fuse in motor)

Fan body

Junction box

Black

Switch

I-Standard

II-Boost

Capacitor

Earth ground

AC120V 60Hz

Power supply

White

Live

Neutral

Motor

White

Red

Black Black

White

Green

Yellow Yellow

Junction box cover

5. Refer to wiring diagram.

Follow all the local electrical safety codes

as well as the National Electrical Code(NEC).

Using UL approved wire nuts, connect house

power wires to ventilating fan wires.

The clamps of the adaptor should be

clipped on fan housing correctly.

Install the adaptor and secure

v duct before installingentilation

junction box.

3. Slide the clamps of the adaptor to the top

of the fan housing and then snap the clamps

of the adaptor into the bottom of the fan

housing opening. (Fig. 2)

4. Remove junction box cover and secure

conduit or strain relief to junction box cover

knock-out hole ( A or B ). (Fig.3)

6. Affix the junction box cover to junction box.

If the knock-out hole is used B , this step

must be performed after step 8.

7. Insert the tongue on the bottom of the

junction box so that it is on the outside of

the fan housing.

Before affixing screw (ST4.2X8), make

sure the tongue of the junction box is

clipped on fan housing correctly. (Fig.3)

8. Affix the junction box to the top of the

fan housing with screw (ST4.2X8). (Fig.4)

Mount junction box cover carefully so

that lead wires are not pinched.

Fig.4

Switch

Screw

(ST4.2X8)

APTO

RJUNCTION

BOX

Fan housing

Junction box

on the bottom of the joist, hang up the fan

housing through the key hole, tighten the

screw, then affix other 2 screws. (Fig.1)

INSTALLATION FOR FV-07VBA1 CONTINUED

10. Finish ceiling work. Ceiling hole should be

aligned with the inside edge of the flange.

(Fig.5)

Fig.5

After finishing the ceiling job, fill gap between flange and

ceiling with caulk or other sealant to prevent air leakage.

7 7/8 (200)

Ceiling

Housing can

9. Select the air volume speed by adjusting

the switch. Factory setting is "I" (Standard)

position; pressing "II" (Boost) s the elects

high airflow position. (Fig.4 of page 5 )

9. Select the air volume speed by adjusting the switch. Factory setting is "I" (Standard) position;

pressing "II" (Boost) s the high airflow position. elects (Fig.4 of page 5 )

INSTALLATION FOR FV-07VBA1(WALL MOUNTING)

After finishing the wall job, fill gap between

flange and wall with caulk or other sealant

to prevent air leakage.

7 7/8 (200)

Housing can

Fig.7

1. Affix the fan housing to stud with 3 long screws

(ST4.2X20) by affixing first 1 screw in front of the

3. Slide the clamps of the adaptor to the top of the fan

housing and then snap the clamps of the adaptor into

the bottom of the fan housing opening. (Fig. 2 of page 5)

2. Install the v duct and secure it with a entilation

clamp and seal it with mastic or approved foil tape.

A 4 inch circular duct is needed to connect to the

relevant part of adaptor. (Fig.2 of page 5)

6. Affix the junction box cover to junction box.

If the knock-out hole is used B , this step must be performed after step 8.

7. Insert the tongue on the bottom of the junction box so that it is on the outside of the fan housing.

8. Affix the junction box to the top of the fan housing with screw (ST4.2X8). (Fig.4 of page 5)

4. Remove junction box cover and secure conduit

or strain relief to junction box cover knock-out

hole ( A or B ). (Fig.3 of page 5)

5. Refer to wiring diagram.

Follow all the local electrical safety codes as well

as the National Electrical Code(NEC).

Using UL approved wire nuts, connect house

power wires to ventilating fan wires.

10. Finish wall work. Wall hole should be aligned with the inside edge of the flange. (Fig.7)

The clamps of the adaptor should be clipped

on fan housing correctly.

Install the adaptor and secure ventilation

duct before installing junction box.

Before affixing screw (ST4.2X8), make sure the tongue of the junction box is clipped on

fan housing correctly. (Fig.3 of page 5)

Mount junction box cover carefully so that lead wires are not pinched.

Fig.6

Fan housing

3 Long screws

(ST4.2X20)

stub, hang up the fan housing through the key

hole, tightenthe screw,then affix other2 screws.

(Fig.6)

Key hole

Stud

Wall

2.Wash and clean grille assembly.

(Use non-abrasive kitchen detergent, wipe dry with

clean cloth.)(Fig.12)

3. Remove dust and dirt from fan body using a

vacuum cleaner. (Fig.13)

1. Remove grille assembly. (Squeeze mounting springs

and pull down carefully.)(Fig.11)

4. Using a cloth dampened with kitchen detergent,

remove any dirt from Fan Body. Wipe dry with

clean cloth. (Fig.14)

5. Replace grille assembly.

WARNING

CAUTION

Fig.12

Fig.13

Fig.14

Ceiling

Vacuum

cleaner

Ceiling

Glove

Fig.11

INSTALLATION FOR FV-07VBB1

3. Insert the grille assembly mounting springs into the

slots as shown and mount grille assembly to fan body .

(Fig.10) Fig.10

Grille assembly

Mounting

spring

Slot

Glove

Mounting

spring

Fan body

Fig.9

Claw

Rib

Plug connector

Ceiling

2. Secure the blower / motor assembly with 2 screw

and connect the molex plug connector from the

blower to the junction box. (Fig.9)

Before turning on the fan, make sure the

connector is inserted at the correct position.

Failure to properly connect will result in fan not

working.(Fig.9)

The claw of connector must latch to the rib

completely.(Fig.9)

CAUTION

WARNING

The blower / motor assembly must be installed

into housing can tightly by the 2 screw . failure

to secure with screw will affect the grounding.

2 Screw

(ST4.2X8)

Blower / motor assembly

Adaptor

flanges

Ceiling

Fig.8

1. Insert the blower / motor assembly by sliding it into

adaptor flanges. Then press lock the blower / motor

assembly into the housing can until the blower

“clicks” into place for temporary fixation. (Fig.8)

INSTALLATION FOR FV-07VBB1

The ducting from this fan to the

outside of the building has a strong effect on the air flow, noise and energy use of the fan. Use

the shortest, straightest duct routing possible for best performance, and avoid installing the fan

with smaller ducts than recommended. Insulation around the ducts can reduce energy loss and

inhibit mold growth. Fans installed with existing ducts may not achieve their rated air flow.

P0816-0 07VBA1M420

Fig.15

Properly insulate the area around the

fan to minimize building heat loss and

gain. (Fig.15)

Loose fill or batt insulation can be

placed directly over the fan housing in

the attic. Our fans and fan/light

combination units do not create

excessive heat that is a common

problem with recessed light fixtures or

some competitor’s fan/light

combination. Our efficient, cool-running

motors and our fluorescent lamps do

not create enough ambient heat to be

subjected to these limitations.

0.7 1.3

1.51.5

Panasonic Corporation 2016

Printed in Mexico

This manual suits for next models

Other Panasonic Air Conditioner manuals

Panasonic

Panasonic CS-C45FFH User manual

Panasonic

Panasonic CS-CE9JKE User manual

Panasonic

Panasonic S-36PU1E5A User manual

Panasonic

Panasonic CS-E24FKR User manual

Panasonic

Panasonic CS-NE9JKE-1 User manual

Panasonic

Panasonic cs-s12pkv User manual

Panasonic

Panasonic CE18JKK-1 User manual

Panasonic

Panasonic CS-MRE7RKE User manual

Panasonic

Panasonic S-22KA1E5 User manual

Panasonic

Panasonic S-36PT1E5 User manual

Panasonic

Panasonic CS-XE7PKEW User manual

Panasonic

Panasonic RS-RE9UK User manual

Panasonic

Panasonic CSXC181KP - ROOM AIR CONDITIONER User manual

Panasonic

Panasonic CZ-06KPU11P User manual

Panasonic

Panasonic CS-V7DKE User manual

Panasonic

Panasonic CS-S9MKR User manual

Panasonic

Panasonic CS-W7MKD User manual

Panasonic

Panasonic U-16GE3E5 User manual

Panasonic

Panasonic CS-PU9WKH-8M User manual

Panasonic

Panasonic CS-A75KR User manual

Panasonic

Panasonic U-26PS1U6 User manual

Panasonic

Panasonic CS-C12KKF-2 User manual

Panasonic

Panasonic CSC18DKU - AIR CONDITIONER - SPLIT User manual

Panasonic

Panasonic U-72MF2U9 User manual

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Frigidaire

Frigidaire FFRE0533S1E0 Use & care guide

Samsung

Samsung AS09HM3N user manual

Frigidaire

Frigidaire CRA073PU11 use & care

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual

Webasto

Webasto Frigo Top 25 DS Instructions for use