Outback TPA101-4 User manual

Model: TPA101-4

Assembly and Operating Instructions for

Outback® Combi Gas Charcoal Barbecue

EN (Europe)

Photographs are not to scale.

Specifications subject to

change without prior notice.

0359

WARNING

•

For outdoor use only. Not for commercial use.

•

Read instructions before using the appliance. Failure to follow instructions could result in death, serious

bodily injury, and/or property loss.

•

Warning: accessible parts may be very hot. Keep young children and pets away.

•

Do not move the appliance during use.

•

Turn off the gas supply at the gas bottle after use.

•

Any modification of the appliance, misuse, or failure to follow the instructions may be dangerous and will

invalidate your warranty. This does not affect your statutory rights.

•

Retain these instructions for future reference.

•

Leak test annually, and whenever the gas bottle is removed or replaced. Check that the hose connections

are tight and leak test each time you reconnect the gas bottle.

•

For Flare-up control please refer to the ‘OPERATION’ section of this manual.

FOR YOUR SAFETY

If you smell gas:

Shut off gas to the appliance.

Extinguish any open flame.

Open barbecue lid or hood.

If odour continues, discontinue use and contact your local

dealer.

FOR YOUR SAFETY

Do not store or use petrol or other flammable vapours or

liquids in the vicinity of this or any other appliance.

A gas bottle not connected for use must not be stored in the

vicinity of this or any other appliance.

Package Contents List

R. Charcoal Bin Right Side

Panel – 1pc.

Q. Charcoal Bin Left Side Panel

– 1pc.

P. Charcoal Bin Bottom Panel –

1pc.

O. Towel Hook – 1pc.N. Front Panel – 1pc.M. Triangle Bracket B – 2pcs.

L. Triangle Bracket A – 2pcs.K. Wheel – 2pcs.J. Axle – 1pc.

I. Bottom Panel – 1pc.H. Caster – 1pc.G. Lockable Caster – 1pc.

F. Right Rear Leg – 1pc.E. Right Front Leg – 1pc.D. Side Support – 2pcs.

C. Left Rear Leg – 1pc.B. Left Front Leg – 1pc.A. Hood and Body Assembly –

1pc.

Package Contents List

Carefully unpack the packing

box and remove all contents

before commencing assembly.

Make sure that you obtain all

correct package contents.

ZM. Match Holder – 1pc.ZL. Crank Handle---1pc

ZK. Drip Tray – 1pc.ZJ. Warming Rack (Gas) – 1pc.ZI. Cooking Grill (Gas) – 2pcs.

ZH. Warming Rack (Charcoal)

– 1pc.

ZG. Cooking Grill (Charcoal) –

1pc.

ZF. Flame Tamer – 3pcs.

ZE. Ash Tray – 1pc.ZD. Grease Cup – 1pc.ZB. Charcoal Bin Lid – 1pc.

ZA. Left Side Shelf – 1pc.Z. Rear Support – 1pc.Y. Right Side Shelf – 1pc.

X. Charcoal Bin Slider – 2pcs.W. Front Support – 1pc.V. Front Trim Panel – 1pc.

U. Charcoal Bin Handle – 1pc.T. Charcoal Bin Front Panel –

1pc.

S. Charcoal Bin Back Panel –

1pc.a

Specifications subject to change without prior notice.

Hardware Pack Contents

AA BB CC DD EE FF IIHHGG

25/32-in. x 6-14 Stage ScrewJJ

45/32-in. x 6 Flat Head ScrewII

81/4-in. x 61 Round Head ScrewHH

101/4-in. Flat WasherGG

21/4-in. NutFF

1Allen KeyEE

401/4-in. Lock WasherDD

321/4-in. x 15 Round Head ScrewCC

545/32-in. Lock WasherBB

545/32-in. x 10 Round Head ScrewAA

QtyDescriptionCode

IMPORTANT!

•TOOLS NEEDED FOR ASSEMBLY: Medium size flat blade or Phillips/Crosspoint screwdriver,

adjustable spanner or metric spanner set.

•The assembly of this barbecue requires 2 people.

•Remove all cooking components, flame tamer and any internal packaging from the Barbecue Body.

•Whilst every care is taken in the manufacture of this product, care must be taken during assembly in

case sharp edges are present.

•Please read the Important Information section carefully before assembly and use of your barbecue.

•Before beginning assembly, make sure all parts are present. Compare parts with package contents list

and diagram above. If any part is missing or damaged, do not attempt to assemble the product. Contact

customer service for replacement parts.

•Note: The left and right sides of the grill are on your left and right as you face the front of the grill.

Assembly

1. Trolley Frame Assembly.

a). Use 4 x Round Head Screws (CC) and 4 x Lock

Washers (DD) to attach left Side Support (D) to Left

Front Leg (B) and Left Rear Leg (C). Ensure that

the flat side faces inwards and the wide lip faces

downwards. See Fig. 1.

b). Use 4 x Round Head Screws (CC) and 4 x Lock

Washers (DD) to attach right Side Support (D) to

Right Front Leg (E) and Right Rear Leg (F). Ensure

that the flat side faces inwards and the wide lip

faces downwards. See Fig. 2.

2. Wheel Assembly

a). Attach one Lockable Caster (G) and one Caster

(H) to the left side of the Bottom Panel (I) using 8 x

Round Head Screws (CC) and 8 x Lock Washers

(DD). See Fig. 3

b). Slide the Axle (J) through the corresponding holes

in the right legs. Slide the Wheels (K) over each

end of the axle. Ensure the coned side of the wheel

is facing the leg. Secure the wheels into place

using 2 x Nut (FF) and 2 x Flat Washer (GG). See

Fig. 4.

Fig. 1

Fig. 2

Fig. 3 G

Fig. 4

B C

FF GG

3. Bottom Panel Assembly

a) Attach the left legs to the Bottom Panel

(I) by threading 4 x Round Head Screws

(HH) through 4 x Lock Washers (DD), 4 x

Flat Washers (GG) to screwing into

bottom panel tightly. See Fig. 5.

b) Repeat the above procedure to attach

the right legs onto the bottom panel.

4. Triangle Bracket Assembly

a). Use 4 x Round Head Screws (AA)

and 4 x Lock Washers (BB) to connect

one Triangle Bracket A (L) to rear right

leg and bottom panel. Repeat the

process to attach one Triangle Bracket B

(M) to right front leg and bottom panel.

See Fig. 6.

b) Repeat the above procedure to attach

remaining Triangle Bracket A (L) to left

front legs and bottom panel and to attach

remaining Triangle Bracket B (M) to left

rear leg and bottom panel. See Fig. 6.

Assembly

Fig. 6

Fig. 5

Fig. 7

Fig. 8

DD HH

DD GG

5. Front Panel Assembly

a). Use 3 x Round Head Screws (AA) and 3 x

Lock Washers (BB) to connect the Front

Panel (N) to Bottom Panel (I). See Fig. 7.

b) Attach Front Panel (N) to Right Front Leg

(E) using 3 x Round Head Screws (AA) and 3

x Lock Washers (BB). See Fig. 7.

c). Use 2 x Round Head Screws (AA) and 2 x

Lock Washers (BB) to attach Towel Hook (O)

to Front Panel (N). See Fig. 8.

Assembly

Fig.9

6. Charcoal Bin Assembly

a). Attach Charcoal Bin Left (Q) and Right

(R) Side Panels to Charcoal Bin Back

Panel (S) by securely hooking back panel

tabs into side panel slots. See Fig. 9.

b). Place Charcoal Bin Back Panel (S) on

a flat level surface. See Fig.10. Securely

hook Charcoal Bin Bottom Panel (P) tabs

into Charcoal Bin Left (Q) and Right (S)

Side Panel slots, and ensure the Charcoal

Bin Bottom Panel (P) is inside the folded

edge of Charcoal Bin Back Panel (S).

c). Use 6 x Round Head Screws (AA) and

6 x Lock Washers (BB) to connect

Charcoal Bin Front Panel (T) to charcoal

bin side panels (Q&R) and bottom panel.

See Fig. 11. Note: Connection tabs go on

the outside of side and bottom panels.

d) Use 2 x Round Head Screws (AA) and

2 x Lock Washers (BB) to attach the

Charcoal Bin Handle (U) to Charcoal Bin

Front Panel (T). See Fig. 12.

Fig. 11

Fig. 12

Fig.10

S Fold side

Back view

Assembly

7.FrontTrimPanel Assembly

a). Position the FrontTrimPanel(V)

againstthe right sideof the charcoal bin

frontpanel.Insertthefronttrimpanel

hinge pinintotheholeonthe bottomof

the charcoal binfront panel.The tabat

the top of thefronttrimpanel goes

againstthe back surfaceof charcoal bin

frontpanel.Holdingfronttrimpaneland

charcoal bin frontpaneltogether,slide

holeonbottomleft sideof charcoal bin

frontpanelontohingepinofleft front

leg.Align the twoholesonthebottom

rightof charcoal bin frontpanelwiththe

holeson thebottompanel.Secure

charcoal bin frontpanelwith2xRound

Head Screws(AA) and2xLock

Washers(BB).See Fig.13.

b). AttachFrontTrimPanel(V) toFront

Panel (N)with3xRoundHead Screws

(AA) and3xLock Washers(BB).See

Fig. 13.

8.FrontSupportAssembly

a). Use4xRoundHead Screws(AA)

and 4xLockWashers(BB) toconnect

FrontSupport (W)toleft/right frontlegs.

See Fig. 14.

b). Use5xRoundHead Screws(AA)

and 5xLockWashers(BB) toconnect

the underside ofthe Front Support(W)

tothe Front Panel (N)andFrontTrim

Panel (V).See Fig.14.

Note:Ensuretheflat sideofthe front

supportfacesoutwards.

9. Charcoal BinSliderAssembly

a). Pulland holdCharcoal BinFront

Panel (T)forward, andinsertthe two

CharcoalBinSliders(X)throughthe

holesintheFrontTrimPanel(V) and

LeftFrontLeg (B).SeeFig.15.

b). Use2xStageScrews(JJ) to

connecttheloop holeendsof the

CharcoalBinSliders(X)totheCharcoal

BinFrontPanel(T).SeeFig.15.

Fig. 13

Fig. 14

Fig. 15

AA BB

WBB

Assembly

10. Rear Support Assembly

Use 4 x Round Head Screws (AA) and 4 x

Lock Washers (BB) to attach Rear Support

(Z) to left / right rear legs. See Fig. 16.

NOTE: Ensure the flat side of the rear

support faces outwards.

11. Charcoal Bin Lid Assembly

Use 4 x Flat Head Screws (II) to connect

hinges of Charcoal Bin Lid (ZB) to Front

Support (W). See Fig. 17.

Fig. 16

Fig. 17

Assembly

CCDD

Fig. 18

Fig. 19

12. Barbecue Body Assembly

NOTE: It requires 2 people to lift the

barbecue body.

a). Carefully place the Hood and Body

Assembly (A) onto the trolley assembly. See

Fig. 18.

WARNING: DO NOT RELEASE THE

BARBECUE BODY WHILE THE

BARBECUE HAS NOT BEEN PROPERLY

SEATED. THIS MAY RESULT IN INJURY

OR DAMAGE TO YOUR BARBECUE.

b). Use 4 x Round Head Screws (CC) and 4

x Lock Washers (DD) to securely attach the

barbecue body to the left / right side supports

(D). See Fig.19.

c). Insert the Crank Handle (ZL) through the

hole in the barbecue body control panel and

screw it into the threaded socket, provided for

raising the charcoal tray.

13. Side Shelf Assembly

Use 6 x Round Head Screws (CC) and 6 x

Lock Washers (DD) to attach Right Side

Shelf (Y) to right front / rear legs. Then use 2

x Round Head Screws (AA) and 2 x Lock

Washers (BB) to attach right side shelf to

main control panel. See Fig. 20.

Repeat above procedure to attach Left Side

Shelf (ZA) to left front / rear legs and main

control panel.

Fig. 20

Table of contents

Other Outback Grill manuals

Outback

Outback Sapphire THG3216AW User manual

Outback

Outback Spectrum Flamer User manual

Outback

Outback Omega 150 User manual

Outback

Outback Modern Classic Trooper User manual

Outback

Outback THG3302P User manual

Outback

Outback Spectrum User manual

Outback

Outback Orion User manual

Outback

Outback Omega 100 User manual

Outback

Outback Omega 200 User manual

Outback

Outback Meteor 3 User manual

Outback

Outback Party FS5680A User manual

Outback

Outback Cook Dome 571 User manual

Outback

Outback THG3710SS-3 User manual

Outback

Outback SG-930 User manual

Outback

Outback Excel 100 User manual

Outback

Outback Omega 201 User manual

Outback

Outback Hunter Plus 3 User manual

Outback

Outback Society/Granite User manual

Outback

Outback THG2216AW User manual

Outback

Outback Jupiter 4S User manual

Outback

Outback CD100 User manual

Outback

Outback MS4464 User manual

Outback

Outback Meteor 4S User manual

Outback

Outback THG3302PC User manual

Popular Grill manuals by other brands

Orbegozo

Orbegozo GR 2300 instruction manual

bora

bora PT11 Operating and installation instructions

Klarstein

Klarstein 10031664 manual

Garland

Garland MWE3W Installation and operation manual

Char-Broil

Char-Broil 463722714 Product guide

Nexgrill

Nexgrill 720-0830HK Operating instruction

Kenmore

Kenmore 415.16123800 Use and care guide

Camp Chef

Camp Chef PG24CLAU Warning & instruction booklet

Tucker Barbecues

Tucker Barbecues GTR Series Assembly, installation and operating instructions

Monogram

Monogram ZGG540NCP1SS owner's manual

Equipex

Equipex Sodir Savoy Operation manual

Gaggenau

Gaggenau VR 414 610 use and care manual

Miele

Miele KM 408-1 operating instructions

George Foreman

George Foreman GGR50B owner's manual

AOG

AOG T series quick start guide

Gorenje

Gorenje TG2000CB Instruction manua

Weber

Weber Genesis Silver-B Permamount NG 051701 owner's guide

Glen

Glen SA 3037 user guide