oticon Amigo eZync User manual
INSTRUCTIONS FOR USE
Amigo eZync
Contents
Introduction 4
Typical package content 5
Preparing the Amigo eZync 6
Powering the Amigo eZync 7
Where to place the Amigo eZync 8
Mounting the Amigo eZync on a wall 10
Placing the Amigo eZync on a shelf 13
LED legend 14
Choosing and changing channels 15
Synchronising the Amigo eZync 16
Synchronising other manufacturers’ receivers 17
Cleaning the Amigo eZync 18
Appendix A: Troubleshooting 19
Appendix B: Manufacturers’ warranty 20
Warning Yellow pages
IMPORTANT NOTICE
Please familiarise yourself with the entire contents of this booklet before using your
Amigo eZync. The booklet contains various statements, safety instructions and
important information about the use and handling of the Amigo eZync.
4 5
Introduction
Congratulations on your decision to take the next step in improving classroom FM.
Amigo eZync belongs to the Amigo FM product family from Oticon – a company that
strives to provide superior solutions for school and home use.
The Amigo family is extremely versatile, making life much easier for users in academic,
professional and social listening situations. With Amigo eZync, channel management in
educational surroundings have become even more manageable.
Amigo eZync is easy to mount on a wall or place on a shelf based on the needs that are
for the specific school or institution.
Typical package content
Wall mount
Fasteners and anchors Instructions for use
Power supply
Model: UE10W-050020SPC
Amigo eZync
Stand for placing the
eZync on a shelf
6 7
Preparing the Amigo eZync
Power jack
On/Off button
LED indicator
Powering the Amigo eZync
To power the Amigo eZync, plug in the power supply (see picture) and connect it to the
wall outlet.
The Amigo eZync has a battery back-up that will last for up to hours. It will automati-
cally switch to battery power when the mains power is disconnected, and vice versa.
The back-up battery may take several hours to
charge when the Amigo eZync is powered for
the first time. The battery charges continuously
whenever the Amigo eZync is plugged in.
NOTE
The battery cannot be replaced by
the user. The Amigo eZync cannot
be opened without damaging it.
8 9
Where to place the Amigo eZync
The Amigo eZync has a synchronisation range
of approximately 1.5 metres. To ensure that the
synchronisation commands actually reach the
Amigo ear-level receivers, it is important to
position the unit optimally.
The best location is close to the door or in the
corridor just outside the classroom. Then you
can be absolutely certain that all receivers will
be continuously synchronised and on the right
channel.
NOTE
The Amigo eZync will automatically synchronise all Amigo ear-level receivers within
range and in all directions (360°). Synchronisation can also take place through walls.
NOTE
It the wall outlet is located too far
away from the Amigo eZync, the
extension power cable can be used.
10 11
Mounting the Amigo eZync on a wall
The optimal position for this unit is 1.5 metre above the floor, next to the entrance (see
page 11).
Use the wall mount as a guide to mark the location of the holes.1.
Drill the two holes in the wall.2.
If necessary, insert anchors inside the drilled holes.3.
Insert fasteners through the washer and wall mount.4.
Gently tighten the until the wall mount is secure. Avoiding bending the wall mount.5.
If the Amigo eZync is to be used in a room, where only younger kids are entering, the
Amigo eZync can be mounted lower than the recommended 1.5 meters.
NOTE
When installing the wall mount, note that the fasteners must not be over-tightened,
as this bend it out of shape.
1.5 m / 60 inches
C
L
12 13
When the wall mount has been installed, plug the power supply into the jack on the
Amigo eZync. The Amigo eZync can then slide onto the wall mount:
Align the Amigo eZync with the wall mount.1.
Once the Amigo eZync is hanging on the wall mount, slide the unit to the left to lock it2.
in place.
To remove the Amigo eZync, lift it a little and slide it to the right.3.
Placing the Amigo eZync on a shelf
If If you occasionally need to move the Amigo eZync, use the
stand that is supplied with the Amigo eZync. Simply connect
the power cord, and place the Amigo eZync on the shelf.
NOTE
When using the portable stand, avoid placing the Amigo eZync anywhere where it can
potentially drop to the floor.
14 15
LED legend
The LED on the Amigo eZync does more than indicate that the power is on. It shows:
Steady red
On and transmitting
Off or Error
Blinking red
Running on battery
back-up
Triple blink
Synchronising command
accepted
Choosing and changing channels
The channel on the Amigo eZync can be changed by synchronising it with an Amigo T20/
T21/WRP.
To change the transmitting channel on the Amigo T20/T21/WRP transmitter, press and
hold either the Sbutton or the Tbutton for two seconds to select one of the prede-
fined lists of channels.
When the channel number begins to blink, press Sor Tto change channel. As soon as
you find the desired channel, press the SYNC button to confirm. The transmitter will then
be locked on to the new channel.
When the channel number is blinking you can return to the original channel by pressing
the C-button. This will also return you to the transmitting screen.
Whenever you need to change channel simply repeat the procedure.
16 17
Synchronising the Amigo eZync Synchronising other manufacturers’ receivers
The Amigo eZync can be synchronised in the first 60
seconds after it has been turned on.
Within a distance of approximately 50 cm, press the SYNC
button on the Amigo T20/T21/WRP. If the synchronisation is
successful, the LED on the Amigo eZync will blink three
times.
With the Amigo eZync you have the possibility to synchronise Amigo ear-level receivers
and Widex ear-level receivers.
Visit www.oticon.com for a full compatibility guide.
NOTE
The Amigo eZync will not syncronise receivers during
the first 60 seconds after it has been turned on.
18 19
Cleaning the Amigo eZync
The Amigo eZync is moisture repellent, making it very easy to clean with a damp cloth.
Appendix A: Troubleshooting
Problem Solution
The LED is not lit Check that the power cable is connected properly.
Check that the Amigo eZync is turned on.
The LED is blinking The Amigo eZync is running on battery back-up.
Check that the power cable is connected properly.
It is not possible to
synchronise the
Amigo eZync
Synchronisation takes place wirelessly with the aid of an Amigo
T20/T21/WRP. If the Amigo eZync fails to confirm (with three
blinks of the LED), try moving the transmitter closer or a little bit
to one side. Then press the SYNC button again.
It is possible to synchronise the Amigo eZync during the first 60
seconds after it is turned on. To change the channel, turn the
Amigo eZync off and on again, and synchronise it once more.
For assistance with troubleshooting, or for answers to other questions, please consult
your hearing care professional. Alternatively, visit www.oticon.com, where you can find a
troubleshooting guide for Amigo.
Table of contents
Other oticon Hearing Aid manuals
oticon
oticon Acto User manual
oticon
oticon Opn Series User manual
oticon
oticon BTE Alta2 Pro User manual
oticon
oticon amigo FM-CI User manual
oticon
oticon RemoteCare User manual
oticon
oticon miniRITE Series User manual
oticon
oticon IIc User manual
oticon
oticon miniRITE Alta2 User manual
oticon
oticon Alta User manual
oticon
oticon Agil User manual
oticon
oticon Alta User manual
oticon
oticon CIC P User manual
oticon
oticon Oticon Xceed Series User manual
oticon
oticon Geno 1 User manual
oticon
oticon Sumo 20DM User manual
oticon
oticon Dual User manual
oticon
oticon Amigo T10 User manual
oticon
oticon miniRITE T User manual
oticon
oticon Streamer 1.4 User manual
oticon
oticon ConnectClip User manual
