Osram e:cue SYMPL Core S User guide
AB447060035
e:cue SYMPL Core S
Setup Manual
Our Brand
www.osram.com/ecue
Light is OSRAM
02
AB447060035
e:cue SYMPL Core S Setup Manual (original issue)
e:cue SYMPL Core S Installationsanleitung (Originalversion)
Edition/Ausgabe: 23.08.19 [EN_DE_SYMPL_Core_S_Setup_v2p0]
Published by / Herausgegeben von:
OSRAM GmbH
Karl-Schurz-Strasse 38
33100 Paderborn, Germany
©2019 OSRAM GmbH, BU Digital
All rights reserved / Alle Rechte vorbehalten
Read the Setup Manual
carefully before unpacking the
product. Subject to
modication without prior
notice. Typographical and other
errors do not justify any claim
for damages. All dimensions
should be veried using an
actual part.
Except for internal use,
relinquishment of the
instructions to a third party,
duplication in any type or form
- also extracts - as well as
exploitation and/or
communication of the contents
is not permitted.
Lesen Sie die
Installationsanleitung vor dem
Auspacken des Produktes
sorgfältig durch. Alle Änderungen
vorbehalten.
Rechtschreibfehler oder andere
Fehler rechtfertigen keinen
Anspruch bei Schäden. Alle
Maße sollten an einem realen
Gerät überprüft werden.
Außer für interne Verwendung ist
die Überlassung dieser Anleitung
an Dritte, die gesamte oder
auszugsweise Veröffentlichung,
Verwertung oder Mitteilung in
jeglicher Art und Form sind nicht
gestattet.
03
Table of Contents / Inhalt
Table of Contents / Inhalt
English 05
1 Security instructions 06
1.1 Symbols 06
1.2 General security instructions 06
2 General device description 07
2.1 Delivery content 07
2.2 Connectors and interfaces 08
2.3 User interface: LEDs 08
2.4 Identify button: Identication & Reset & Update 09
3 General remarks 10
3.1 Transport 10
3.2 Unpacking 10
3.3 Warranty regulations 10
3.4 Maintenance and Repair 10
3.5 Disposal 11
3.6 Support 11
4 Installation 11
4.1 Installation conditions 12
4.2 Mounting process 12
4.3 Ethernet connection 12
4.4 Power supply 13
5 Network configuration 13
5.1 Default network properties 14
5.2 Network conguration with SYMPHOLIGHT 14
5.3 Network conguration with the web interface 15
6 Firmware Update 17
7 Dismounting 20
8 Product specifications 20
05
English
06
Security instructions
1 Security instructions
Please read the safety instructions, provided in a separate manual, carefully.
Make sure that the environmental, mounting, and installation prerequisites
are met. This manual should be kept at a safe place and in reach of the
installation.
1.1 Symbols
!
The exclamation mark warns about possible damage of the
device itself or connected devices.
i
The information symbol gives general hints and informs
about handling and procedures for use of the device.
1.2 General security instructions
!
Connect cables and data only when the device is powered
down.
!
The device must be supplied by a separate certied SELV
Class 2 power supply.
!
The maximum length of each connected cable is 30 m.
i
If safety instructions are missing, please contact OSRAM to
receive a new copy.
07
General device description
2 General device description
e:cue SYMPL Nodes are a system of interfaces for e:cue SYMPHOLIGHT
only. They provide various connection types like DMX512, DALI, digital
inputs and outputs etc. SYMPL Nodes always operate in online mode, as a
device interface for SYMPHOLIGHT. All interactions are initiated and
controlled by SYMPHOLIGHT. Connections between servers, Cores and
Nodes are always made with e:net via Ethernet.
e:cue SYMPL Core S is a stand-alone engine for e:cue SYMPHOLIGHT
with SYMPL Nodes as interfaces. It executes SYMPHOLIGHT shows in
small to medium-sized shows and controls all available SYMPL Nodes. As
a user interface it utilizes the Action Pad of SYMPHOLIGHT with all usual
web browsers. The connection between SYMPL Core S, external systems
and the Nodes is a standard Ethernet network. Shows can be transferred
to the SYMPL Core S from a SYMPHOLIGHT server or uploaded from
many sources.
2.1 Delivery content
Delivery content for the e:cue SYMPL Core S (AB447060035):
1. e:cue SYMPL Core S
2. Safety instructions
3. Installation guide (English only)
i
To operate SYMPL Nodes a SYMPHOLIGHT version 2.0 or
higher is mandatory. Earlier versions do not support the
SYMPL Nodes. SYMPL Nodes are not supported by the
e:cue Lighting Application Suite.
i
e:cue SYMPL Core S is not hot-pluggable.
08
General device description
2.2 Connectors and interfaces
View from top
1Master/Slave LED
2Error/Status LED
3Ethernet link LED (e:net, LAN activity)
4Power LED
5Identify button
6micro SD card slot
7Power supply
(Vcc–, Vcc+ left to right)
8e:net/Ethernet
9USB 2.0 socket
2.3 User interface: LEDs
The SYMPL Core S has four LEDs. The four LEDs show the basic states of
the SYMPL Core S.
LEDs
Master/Slave Blue: This SYMPL Core S is master in a master/slave
group.
Yellow: This SYMPL Core S is a slave in a master/slave
group.
Error/Status Green: Signals system activity.
Orange: System load reaches 100%.
Red: A system error occurred. Restart the system by
disconnecting the power supply. If the error persists,
contact OSRAM Service.
09
General device description
Ethernet link Off: No network connection available.
On: If constantly alight, network connection available.
Flashing: Data trafc over network.
Power On: Device is in operation.
2.4 Identify button: Identification & Reset & Update
The Identify button has four functions: to send an Identify message (A), to
reset the SYMPL Core S (B), and to update the rmware of the
SYMPL Core S (C).
(A) A short press during operation in online mode sends an Identify
message to the server. This helps to assign the SYMPL Core S in the
Layout in SYMPHOLIGHT.
(B) The Identify button can also be used to reset the device to factory state
or to stay in bootloader mode:
• Keep the Identify button pressed while powering up, Status and
Test / Error light up at rst. Bootloader mode is signaled by a fast
blinking Status LED. Release the button now. The device stays in
bootloader mode to download a new rmware.
To exit the bootloader mode, short press the Identify button again.
• Press the Identify button until Status and Test / Error LEDs blink
alternating, then blink together. Releasing the button now resets the
device to its factory settings. The password and other settings are reset
to their default values. Please note that the Ofine Content cannot be
reset. To employ a reset Startup behavior, a restart of the device is
required.
• Keeping the button pressed further on, the device proceeds to
normal operation. No changes apply.
(C) The Identify button is also part of the rmware update process using an
USB ash drive. See for further information.
10
General remarks
3 General remarks
3.1 Transport
Only transport the device in its original packaging. This protects the device
from damage.
3.2 Unpacking
Only unpack the e:cue SYMPL Core S at its installation location. To protect
the device against condensation water, unpack it and wait until all moisture
remaining in the device has evaporated. Condensation can occur when the
device is moved from a cold to a warm location. Keep the packaging for
use in case of further transport. Inspect all parts for completeness regarding
chapter „2.1 Delivery content“ on page 07. If there is apparent damage
to the device or parts are missing from the delivery scope, please contact
the OSRAM Support service.
3.3 Warranty regulations
Depending on the product, guaranty regulations are of different duration.
The warranty time is usually noted in the quote and in the order
conrmation. See “Services” “OSRAM Guarantee” at www.osram.com
for details. Legal warranty regulations apply in any case.
3.4 Maintenance and Repair
This device requires no maintenance.
!
Before dismounting, appropriate measures must be taken to
protect the respective components against damage caused
by electrostatic discharge (ESD protection).
!
Do not try to repair the device. Return it to your OSRAM
distributor for replacement or repair.
This manual suits for next models
1
Table of contents
Other Osram Recording Equipment manuals
Osram
Osram e:cue SYMPL input Node User guide
Osram
Osram e:cue SYMPL Switch User guide
Osram
Osram e:cue Bridge8 Specification sheet
Osram
Osram e:cue SYMPL bridge Node Specification sheet
Osram
Osram e:cue SYMPL e:bus Node User guide
Osram
Osram e:cue SYMPL dmx User guide
Osram
Osram e:cue SYMPL relay Node User guide
Osram
Osram e:cue SYMPL dali Node User guide
