Omron FLOW EM2100 User manual
Fleet Operation Workspace (FLOW) Service Guide
18982-008 Rev C
Fleet Operation Workspace (FLOW)
EM2100 & AMR
Service Guide
P/N 18982-008 Rev A FLOW Service Guide
This page intentionally left blank
FLOW Service Guide P/N 18982-008 Rev A
Introduction
This guide provides procedures for disassembly and assembly necessary for the maintenance
of Omron’s EM2100 Appliance and autonomous mobile robots (AMRs).
The qualification of the worker
The worker should have received proper training and have the ability to implement the work
safely. The worker should be familiar with working on electronic equipment and use proper
electrostatic discharge (ESD) procedures. Make sure to read and understand this Service Guide
before starting any work. Omron recommends reading and understanding the following manuals
in addition to this Service Guide:
oEM2100 Installation Guide
oFleet Operations Workspace Core User’s Guide (Document Number: 20569-020)
oLD Service Manual (Document Number: 18745-000)
P/N 18982-008 Rev A FLOW Service Guide
2
Table of Contents
INTRODUCTION ................................................................................................................................................... 1
TABLE OF CONTENTS....................................................................................................................................... 2
REVISION HISTORY .......................................................................................................................................... 3
01. REPLACING DONGLES IN THE EM2100 ................................................................................................... 4
02. REPLACING DONGLES IN AMRS............................................................................................................... 7
03. REPLACING A FAILED EM2100 .................................................................................................................. 9
04. REPLACING A FAILED EM1100 .................................................................................................................11
FLOW Service Guide P/N 18982-008 Rev A
Revision History
Rev
Modified Date
Contents / Reason
Created by
A
June 7, 2019
Original release
Sam Muse
P/N 18982-008 Rev A FLOW Service Guide
4
01. Replacing Dongles in the EM2100
Use the following procedure to remove and replace either the EM2100 FLOW License Dongle or the EM2100 Legacy
License Dongle in the EM2100. The EM2100 FLOW License Dongle uses a battery that has a lifespan of
approximately 5 years. Therefore, it is recommended to change the battery every 4 years. Contact the license
administrator to find out how old a dongle is.
CAUTION: ESD DAMAGE RISK. Protect the appliance from damage caused by electrostatic
discharge (ESD). Wear a grounded wrist or shoe strap whenever removing top cover from the
EM2100.
1. Locations
Parts and tools needed to replace dongles in EM2100 are:
2. Replacement Parts
Part Name
Type
Quantity
Image
1
EM2100 FLOW License Dongle (large black)
14364-200F
1
2
EM2100 Legacy License Dongle (small green)
13131-210F
1
3. Consumables
Name
Note
1
N/A
N/A
4. Necessary Tools
Name
Note
1
Phillips screwdriver
No. 1
Dongles inside of EM2100
FLOW Service Guide P/N 18982-008 Rev A
5. Replacing Dongles in an EM2100
Step
Check Item
Task to be Performed
Check
1
Identify
Dongle ID
In SetNetGo (SNG) go to the license tab. Record the EM2100 FLOW License ID Number.
Include this number when sending C2V to license administrator. Note: This step is only
necessary when replacing the EM2100 FLOW License Dongle
□
2
Turn off
EM2100 and
remove
power
Turn off the power on the front panel using the Soft Shutdown procedure specified in the
EM2100 Installation Manual. Turn off the power on the back panel. Unplug power.
□
3
Remove from
rack
If installed in a rack, remove the EM2100 appliance from the rack. To do this pull the EM2100
forward until it is fully extended from track. Press the locking bottons on the side of the rail
and continue to pull until the EM2100 comes out rack. See the EM2100 Installation Guide for
more information.
□
4
Remove the
top panel
Screw size
PH1
4-40
Set the EM2100 appliance on an ESD protected workspace and follow standard ESD
grounding procedures prior to opening the unit. Using the Phillips head screwdriver, remove
the eight screws circled in red on the top of the EM2100. Slide the top back until it stops, lift
and remove the cover. Place cover upright to avoid scratching the top.
□
CAUTION: Wear an ESD strap
P/N 18982-008 Rev A FLOW Service Guide
6
Step
Check Item
Task to be Performed
Check
5
Replace
EM2100
FLOW
License
Dongle
Remove old EM2100 FLOW License Dongle and insert new dongle.
□
6
Replace
EM2100
Legacy
License
Dongle
Remove old EM2100 Legacy License Dongle and insert new dongle.
□
7
Place cover
back on and
power up unit
Replace the top panel, install the retaining screws and return the EM2100 to the rack. Plug in
power supply cable. Set power switch on back panel to the On position and then set power
switch on front panel to the On position.
□
8
Enable
entitlement
If replacing EM2100 FLOW License Dongle, follow the procedure in the FLOW CORE
User’s Guide section 7.6(Licensing Tab) for enabling entitlement. If only the EM2100 Legacy
License Dongle was replaced no further steps are required.
□
FLOW Dongle
Legacy Dongle
FLOW Service Guide P/N 18982-008 Rev A
02. Replacing Dongles in AMRs
Use the following procedure to replace the AMR Legacy License Dongle or the AMR FLOW License Dongle in an
AMR. Installation is the reversal of removal.
1. Locations
Parts and tools needed to replace dongles in the AMR are:
2. Replacement Parts
Part Name
Part Number
Quantity
Image
1
ARM FLOW License Dongle (small blue)
13131-100F
1
2
ARM Legacy License Dongle (small green)
13131-000F
1
3. Consumables
Name
Note
1
N/A
N/A
4. Necessary Tools
Name
Note
1
T-type hexagon socket wrench
4mm
2
Torque Driver
1-5Nm
3
Hex Key
4mm
4
Philips screwdriver
Point size 1,
Diameter 5mm
5
Flat-head screwdriver
Point size 2.5mm
Thickness 0.35 mm
LD Robot Core
P/N 18982-008 Rev A FLOW Service Guide
8
5. Replacing Dongles in AMRs
Step
Check Item
Task to be Performed
Check
1
Download
Debug info and
check for
installed
advanced
features
Follow the procedure in the LD service manual (18745-000) section 1-1 (Download the file)
and section 1-2 (Download the Debug info file). This will backup the system in case of
AMR core failure. In SNG, under the Licensing tab, check if there are any advanced
feature packs installed. If there are any advanced feature packs record the License # to be
sent along with the C2V file.
□
2
Remove the LD
core
Follow steps 1-8 in LD service manual (18745-000) section 2-2-1. Replacing the LD core
□
3
Install dongle
Remove failed dongle and install new dongle/s.
Note: Position of dongles is not important.
□
4
Enable
entitlement
If installing advanced feature software follow the procedure in the FLOW CORE User’s
Guide section 7.6(Licensing Tab) for enabling entitlement.
□
This manual suits for next models
1
Table of contents
Other Omron Network Hardware manuals
Omron
Omron G70A User manual
Omron
Omron Promi-SD User manual
Omron
Omron ERT1 Series User manual
Omron
Omron E3X-DRT21-S User manual
Omron
Omron DeviceNet DRT2-ROS16 User manual
Omron
Omron CS CJ1W-ETN21 User manual
Omron
Omron JUNMA - User manual
Omron
Omron CJ1W-PNT21 User manual
Omron
Omron V330-F Series User manual
Omron
Omron DEVICENET SAFETY - CONFIGURATION 05-2005 Quick guide
Omron
Omron CS1W-SLK11-21 - 06-2004 User manual
Omron
Omron GRT1 - 11-2007 User manual
Omron
Omron CJ1W-ETN11 User manual
Omron
Omron ITBC-CST01 - 09-2000 User manual
Omron
Omron 3G3MV-PDRT2 User manual
Omron
Omron J7KNA - User manual
Omron
Omron NX Series Instruction Manual
Omron
Omron DRT2 SERIES DEVICENET SLAVES - OPERATION ... User manual
Omron
Omron CJ Series Instruction Manual
Omron
Omron WIRED REMOTE I-O - SYSTEM User guide
Popular Network Hardware manuals by other brands
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL product manual
B&B Electronics
B&B Electronics ZXT9-IO-222R2 product manual
Yudor
Yudor YDS-16 user manual
D-Link
D-Link ShareCenter DNS-320L datasheet
Samsung
Samsung ES1642dc Hardware user manual
Honeywell Home
Honeywell Home LTEM-PV Installation and setup guide
