OmniPrint DTF User manual
DTF Hardware
Assembly Manual V2
PART NAME
QTY
DESCRIPTION
DTF Machine
1
Heater
1
Right Support
1
Left support
1
Bottom
Support
(heater)
2
Middle
Support
(table)
1
Middle
Support
(Heater)
1
Union Bridge
1
Bridge
1
Front Plexi
1
PART NAME
QTY
DESCRIPTION
omni DTF
software and
documents
1
Rip software
dongle
1
Rip software
thumb drive
1
Allen Wrench
4mm
1
Allen Wrench
5mm
1
Screwdriver
Phillips #1
1
Screwdriver
Phillips #2
1
Extra-long
needle nose
Pliers
1
Ethernet
adapter
1
USB -A to
USB- C
adapter
1
Ethernet
cable
1
Power cable
2
Roll of Film (50
m Hot Peel)
1
Roll of Film (50
m Cold Peel)
1
DTF Powder
1 (1Kg)
Humidity &
temperature
gauge
1
Starter kit and
maintenance
supplies
1
PART NAME
QTY
DESCRIPTION
Left Support
Bracket
1
Right Support
Bracket
1
Left Roll
Support (DTF)
1
Right Roll
Support (DTF)
1
DTF Roll
2
Cardboard Roll
Core (14.5x3 DIA)
1
M8 Screw
32
M5 Screw
10
Washer
8
M10 Nut
8
M6 Flanged
Button Screw
12
Leveling Feet
8
Cylinder Bottle
-8 oz
1
TABLE
1. Attach the LEFT and RIGHT support pieces to the MIDDLE SUPPORT (table) using 8 M8 SCREWS (image 1).
2. Place 2 BOTTOM SUPPORT pieces inside the left and right supports (image 2).
3. Place 4 LEVELING FEET and tightening them with 4 M10 NUT (image 3).
Image 1 Image 2
Image 3
PART NAME
QTY
DESCRIPTION
Right Support
1
Left support
1
Middle
Support(table)
1
Leveling Feet
4
M10 Nut
4
M8 Screw
8
4. Assemble the LEFT and RIGHT brackets to the DTF machine using 4 M8 SCREW (image 4)
5. DISASSEMBLE the screws placed in the black upper base on the DTF and use them to assemble the UNION BRIDGE piece. (image 5)
Image 4 Image 5
Image 6
PART NAME
QTY
DESCRIPTION
DTF Machine
1
Union Bridge
1
M8 Screw
4
6. Assemble the LEFT SUPPORT and RIGHT SUPPORT parts at the rear of the machine using 8 M5 SCREWS for the side walls and 2 M5 SCREWS for the bottom
wall (image 7 & 8)
7. On the first lower opening of the LEFT and RIGHT Support bracket mount the piece DTF ROLL, LEFT ROLL SUPPORT (DTF) and RIGHT ROLL SUPPORT (DTF)
(image 9)
Image 7 Image 8
Image 9
10
8. Assemble a DTF ROLL piece in the free hole so that it passes through the holes of the LEFT and RIGHT ROLL SUPPORT (DTF) pieces (image 10)
9. Place the COLD FILM on the LEFT and RIGHT ROLL SUPPORT (DTF) pieces (image 11)
10. Adjust the side screws on the LEFT and RIGHT SUPPORT BRACKET parts on both sides. (Image 11 red circles)
NOTE: make sure the two tubes are the same distance apart from the ends.
Image 10 Image 11
11. Pass the COLD FILM over the Rear opening of the DTF machine and CAREFULLY move the yellow plate back (image 12)
NOTE: this yellow plate will cause the BLACK ROLLERS to rise and the COLD FILM can pass over the machine until it reaches the front.
12. Arrange the COLD FILM so that it is centered on the black plate of the DTF (image 13)
13. Once centered, tighten the screws of the RIGHT and LEFT ROLL SUPPORT (DTF) so they cannot move (image 14)
Image 12 Image 13
Image 14
HEATER
14. Attach 2 BOTTOM SUPPORT HEATER pieces to the MIDDLE SUPPORT (Heater) using 8 M8 SCREWS (image 15 & 16).
15. Assemble 4 LEVELING FEET pieces and tighten using 4 M10 NUT (image 17)
Image 15 Image 16
Image 17
PART NAME
QTY
DESCRIPTION
Bottom Support
Heater
2
Middle Support
(Heater)
1
Leveling Feet
4
M10 Nut
4
M8 Screw
8
16. Assemble the HEATER on the 2 BOTTOM SUPPORT using 8 FLANGED BUTTON SCREW and 8 WASHERS (image 18)
NOTE: CAREFULLY place the heater upside down on a table to be able to assemble the screws easily.
17. CAREFULLY turn the heater back over and attach the ROLL to the LEFT and RIGHT HANDLE pieces using 2 M6 SCREW (image 19)
18. Assemble a ROLL on the RIGHT and LEFT ROLL SUPPORT pieces and attach it on the ROLL already assembled in the previous step using 2 M6 SCREW (image
20)
Image 18 Image 19
Image 20
19. Insert the BRIDGE part inside the HEATER (image 21)
20. Remove the 2 screws found on the black plate of the DTF and put them back to assemble the BRIDGE part (image 22)
21. Assemble the UNION BRIDGE piece to the HEATER using 4 M6 Flanged Button Screw (image 23)
Image 21 Image 22
Image 23
PART NAME
QTY
DESCRIPTION
Bridge
1
M6 Flanged
Button Screw
4
Other OmniPrint Printer manuals
OmniPrint
OmniPrint DIRECT HEAT User manual
OmniPrint
OmniPrint OM100 User manual
OmniPrint
OmniPrint Direct Treater Dual User manual
OmniPrint
OmniPrint FREEJET 330TX User manual
OmniPrint
OmniPrint OM5200 User manual
OmniPrint
OmniPrint OM-200 Owner's manual
OmniPrint
OmniPrint FREEJET 330TX User manual
OmniPrint
OmniPrint OM9500F User manual
OmniPrint
OmniPrint FreeJet320 TX User manual
OmniPrint
OmniPrint OM9500-II User manual
