Oki GL408e User manual

Other manuals for GL408e

5

This manual suits for next models

2

Table of contents

Popular Printer manuals by other brands

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series quick start guide

Evolis

Evolis Elypso user guide

Kyocera

Kyocera FS-9530DN specification

Canon

Canon LASER SHOT LBP-1210 Specifications

Samsung

Samsung BIXOLON SRP-350plusF user manual

Canon

Canon PIXMA PRO-1 Series Getting started

Canon

Canon PIXMA G3560 Online manual

Dell

Dell Color Laser Printer 2130cn user guide

Tektronix

Tektronix Phaser 840 user guide

Epson

Epson ET-7750 Programming guide

Canon

Canon CLBR 460ps Service manual

Eltron

Eltron P210 Guide manual

Ricoh

Ricoh MD-P1 Service manual

Epson

Epson SC-F7100 series user guide

Epson

Epson Stylus C40UX Service manual

Canon

Canon imagePASS-A2 Service guide

Canon

Canon S820D user guide

Read this Installation Guide before and during the installation

of the above accessory. Keep this Installation Guide handy

for future reference.

SIMPLE-DISPENSER INSTALLATION GUIDE

GL 4xxeSeries

For printer models:

2

Simple-Dispenser Installation Guide

1 General

1.1 Important information

This quick guide provides important information on how to setup your new

SATO product.

Be sure to read this quick guide thoroughly before using this printer. It is

an integral part of the product and should be kept in the immediate vicinity

of the device and available to the operating staff.

1.2 Limitation of liability

All information in this manual have been compiled under due

consideration of federal standards and regulations.

The manufacturer will not be held liable for damage resulting from:

zDisregarding these instructions

zUnintended use of the printer

zUnauthorized technical modifications

zUse of unapproved spare parts

zUse of unapproved consumables

FCC WARNING

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

NOTICE

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation.

This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

3

Simple-Dispenser Installation Guide

1.3 Explanation of symbols

This instruction manual uses various warning icons to help you

understand the safe operation of your printer. Explanations of the icons

are below.

WARNING!

Indicates neglectful or erroneous use may cause

irreparable damage to the product, serious injury to the

operator, or worse.

CAUTION!

Indicates a specific point where caution should be used.

The graphic within the triangle will indicate the specific

issue, i.e.; the sign on the left indicates a caution for

potential electrical shock.

CAUTION!

Indicates a potentially hazardous situation which, if

not avoided, may result in damage to your product

or host equipment.

NOTE!

Emphasizes useful tips or recommendations for

efficient and smooth operation of your printer.

4

Simple-Dispenser Installation Guide

1.4 Contact and Document Information

Extensive contact information of worldwide SATO operations can be found on the Internet at

www.satoworldwide.com

Version: SI-GL4xxe-01rA-05-06-07-SSDIG © Copyright 1994 – 2007

All rights reserved. No part of this document may be reproduced or issued to third parties in

any form whatsoever without the express permission of SATO. The materials in this document

are provided for general information and are subject to change without notice. SATO assumes

no responsibilities for any errors that may appear.

5

Simple-Dispenser Installation Guide

GL4xxe Simple-Dispenser Installation

The Simple Dispenser comes with its own front cover to replace the factory-installed

front cover of the GL4xxe series printer. Follow the procedures below to install the

Simple Dispenser.

1. Make sure the printer is OFF and disconnected from the power supply.

2. Lift up the side cover to access the original housing cover (1).

3. Remove the original housing cover by unscrewing the thumbscrew (2) at the

side of the printer.

Figure 1. Removing the existing front cover and preparing to install the replacement cover.

1

4

2

6

Simple-Dispenser Installation Guide

GL4xxe Simple-Dispenser Installation

4. Affix the dispenser (3) to the printer by plugging the white connector (4) into

the complementary connector (4) on the printer.

5. Mount the simple dispenser by hooking it as shown in the illustration at the

bottom of the page. Affix the dispenser with three supplied screws.

6. Mount the replacement front cover (5) onto the front of the printer, using the

thumbscrew removed in Step 3 to screw it back into place. Note: Ensure that

the cable is not pinched when you install the label cutter cover in place.

7. Restore power to the Printer and configure the printer to use the dispenser

(see next page).

Figure 2. Installing the dispenser and replacement front cover

5

3

4

7

Simple-Dispenser Installation Guide

Dispenser setup via the LCD Menu

1. Turn the printer ON and wait for it to initialize and go into ONLINE mode.

2. Press the Line Button to go to OFFLINE mode.

3. Press the Function Button to display the different menu icons

4. Select the Advanced Mode Menu and press the Enter Button.

5. Scroll to the Media Handling menu using the cursor buttons.

6. Once the simple dispenser has been installed correctly, this menu

allows you to select the Peel-Off option to activate the dispenser’s

functionality. A Remove Label message will display on the LCD

prompting label removal for each label that has been printed.

7. When done, go back to ONLINE mode after saving the new settings.

GL4XXE SIMPLE-DISPENSER CONFIGURATION

OFFLINE

ADVANCED MODE

Figure 3. Setting

the Media

Handling option

Peel-Off

8

Simple-Dispenser Installation Guide