OHAUS Explorer E1F110 User manual
Ohaus Explorer
Manufacturer: Ohaus
Product Range: Explorer
Model Tested: E1F110
Capacity - 6100g
Readability - 0.1g
Note:
The Explorer normally comes with an RS232 serial interface fitted as standard, please check with your balance supplier
that this is the case.
Setting up the balance:
• Getting into RS232 Mode
Turn the unit on.
Press the “Setup” button.
Press the “right” button until “RS232” is displayed then press the “Enter” button.
• Setting the Baud rate to 1200.
“BAUD” should now be displayed, press the “Enter” button.
Press the up or down buttons until “1200” is displayed then press the “Enter” button.
• Setting the Parity to none.
“PARITY” should now be displayed, press the “Enter” button.
Press the up or down buttons until “nonE” is displayed then press the “Enter” button.
• Setting the Data to 7 bits.
“DATA” should now be displayed, press the “Enter” button.
Press the up or down buttons until “7” is displayed then press the “Enter” button.
• Setting the Stop bits to 2.
“STOP” should now be displayed, press the “Enter” button.
Press the up or down buttons until “2” is displayed then press the “Enter” button.
• Setting Lock to Off.
“LOCK” should now be displayed, press the “Enter” button.
Press the up or down buttons until “OFF” is displayed then press the “Enter” button.
• Returning to normal operation.
“EXIT” should now be displayed, press the “Enter” button.
Serial Balance Adapter Data Sheet OH-2
Setting up the balance (continued):
• Getting into Print setup mode.
Press the “Setup” button.
Press the “right” button until “PRINT” is displayed then press the “Enter” button.
• Setting the balance to autoprint.
“AUTOPRT” should now be displayed, press the “Enter” button.
Press the up or down buttons until “CONT” is displayed then press the “Enter” button.
• Returning to normal operation.
Press the left or right buttons until “Exit” is displayed, press the “Enter” button.
The balance is now set up to work with the LogIT Serial Balance Adapter - See Connecting the Balance for details of the
lead required to connect the balance to the LogIT Adapter.
Connecting the balance:
A cable must be made to connect the balance serial port to the LogIT Serial Adapter using the wiring information below.
Explorer RS232 port, 9 way D Socket Balance Adapter, 9 Way D Socket
pin 2 pin 2
pin 5
pin 6
pin 7 pin 5
Note: These connection instructions are designed for use with the 9 pin boxed version of the LogIT Serial Balance
Adapter. If using the original 25 pin lead type connection you need to use adapter pin 3 instead of pin 2 (data out) and
adapter pin 7 instead of pin 5 (ground).
Serial Balance Adapter Data Sheet OH-2
Connect balance pin 5 to pin 6 to bypass handshaking
Table of contents
Other OHAUS Scale manuals
OHAUS
OHAUS Adventurer AX224N User manual
OHAUS
OHAUS Scout pro User manual
OHAUS
OHAUS ES series User manual
OHAUS
OHAUS CS 200 User manual
OHAUS
OHAUS Scout SKX Series User manual
OHAUS
OHAUS Pioneer PJX Series User manual
OHAUS
OHAUS AV412 User manual
OHAUS
OHAUS TROOPER SCALE User manual
OHAUS
OHAUS 5000 User manual
OHAUS
OHAUS VF Series User manual
OHAUS
OHAUS ES6R User manual
OHAUS
OHAUS CS 2000 User manual
OHAUS
OHAUS Emerald Series User manual
OHAUS
OHAUS Ranger Count 2000 Series User manual
OHAUS
OHAUS Adventurer AX124 User manual
OHAUS
OHAUS Valor 1000 User manual
OHAUS
OHAUS Valor 1000 User manual
OHAUS
OHAUS HS-120 User manual
OHAUS
OHAUS FD Series User manual
OHAUS
OHAUS SCOUT II User manual
