NTI ENVIROMUX Series User manual

MAN355 Rev Date 10/24/2019

E-IPCAM-SWHNO

Solar Panel IP Camera with WiFi and LAN

Support

Installation and Operation Manual

ENVIROMUX®Series

TRADEMARK

ENVIROMUX is a registered trademark of Network Technologies Inc in the U.S. and other countries.

retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,

without the prior written consent of Network Technologies Inc, 1275 Danner Drive, Aurora, Ohio 44202.

CHANGES

The material in this guide is for information only and is subject to change without notice. Network Technologies Inc reserves the

right to make changes in the product design without reservation and without notification to its users.

TABLE OF CONTENTS

Introduction......................................................................................................................................................................1

Materials..........................................................................................................................................................................1

Preparation for Installation ..............................................................................................................................................1

Installation .......................................................................................................................................................................2

Use with ENVIROMUX..................................................................................................................................................11

Troubleshooting.............................................................................................................................................................12

Technical Specifications................................................................................................................................................12

Warranty Information.....................................................................................................................................................14

NTI SOLAR PANEL IP CAMERA

INTRODUCTION

The E-IPCAM-SWHNO Solar Panel IP Camera with WiFi and LAN support is an HD 1080P 2MP Outdoor Solar Powered Security

WiFi IP Camera with IR-cut Motion Detection. The camera provides ONVIF support and is ideal for P2P Surveillance CCTV

applications.

Features:

- 1080P 2.0MP HD high-resolution camera provides clear and accurate video footage both day and night

- Built-in 2 x 12Ah Li-ion battery for storing power, camera can work for 48 hours without sunshine charging

- IR-cut dual filter, clearer night vision, never be in the dark again

- IP66 waterproof means this camera is suitable for outdoor locations

- Easy to set up. You can separate the solar panel to aim at the sun

- Supports motion detection and can send alarm information by email

- Built-in 16G TF card for recording

- AP function allows connection to AP hotpot signal, working without Internet connection

- Supports up to 6 users to simultaneous live view at the same time

- No need to preset camera, offers free P2P, plug and play, support for QR code scanning to view

- Supports ONVIF protocol

- Support for Android, iOS and Windows

- Easy to install wirelessly

MATERIALS

Materials supplied with this kit:

E-IPCAM-SWHNO IP Camera

1 x 100-240VAC, 50 or 60Hz-5VDC/3A (PS4191) AC Adapter

Solar Panel

Antenna

Hardware for mounting

Mounting Bracket

Power Splitter cable

URL Slip with path to this manual

PREPARATION FOR INSTALLATION

If you want to access the camera from you smart phones/ devices, download and install the APP before you setup the IP Camera.

Search on Google Play store or APP Store for "IPC View".

For connection from a PC, download and install the OCX_Setup.exe and HiP2P Client_Setup_v6.0.3.2.exe from our website.

NTI SOLAR PANEL IP CAMERA

INSTALLATION

1. Secure the mounting bracket to the camera with the hex boltssupplied.

2. Connect the solar panel to the mounting bracket with the 4 Phillips head screws provided.

NTI SOLAR PANEL IP CAMERA

3. Attach the antenna to the camera.

4. Connect the power splitter cable to the solar panel. Then remove the protective boot from the AC Adapter connection jack

and plug in the DC plug.

After the battery is charged, the AC adapter is optional. If the environment provides enough sunshine to the solar panels, the AC

adapter will not be necessary.

Optional AC Adapter plugs

in here.

Remove the protective boot

and insert the DC Plug.

NTI SOLAR PANEL IP CAMERA

5. Attach the power splitter cable to the camera at the connection cable.

6. If using a wired LAN connection, connect the Ethernet cable to the RJ45 connector next to the power splitter cable connection.

7. Anchor the bracket to the desired mounting surface with hardware sufficient to support the full weight of the assembly (6.6 lbs

(2993.7 g)).

Optional LAN

connection cable

attaches here

Notice Reset

button location

The power splitter cable or the DC plug from

the AC adapter are connected here.

NTI SOLAR PANEL IP CAMERA

LED Indications

Charging LED

1. When the Charging LED blinks red, the battery charge level is approximately 30%.

2. When the Charging LED blinks green and red, the batter charge level is approximately 50%.

3. When the Charging LED blinks green, the batter charge level is approximately 80%.

4. When the Charging LED is solid green, the batter charge level is 100%.

Power LED

When the camera is being charged by the solar panel or AC adapter, the Power LED will illuminate blue. The camera will take 30

seconds to completely boot up.

Note: It is recommended to charge the camera using the AC adapter for at least 8 hours before using the camera.

Powering OFF the camera

1. While the camera is working, unplug the power splitter cable from the camera connection cable. Wait 60 seconds.

2. Remove the DC plug of the AC adapter from the power splitter cable, and insert the DC plug directly into the camera

connection cable.

3. Insert and remove the DC plug 3 times. The Power LED will turn OFF.

4. Repeat this if the Power LED does not turn OFF.

Charging LED

Power LED

Front View of Camera

NTI SOLAR PANEL IP CAMERA

Connection

Peer to Peer

The camera can be connected to (using a smart phone or other WiFi enabled device) directly through WiFi AP once it is powered

up, provided a network cable is not attached to it. Search and directly connect through WiFi Settings "CAMxxxxxx". The default

WiFi password is 123456789.

Then use the Search Tool or APP "IPC View" to locate the camera.

Wired Network Connection

Connect the camera to your router using Ethernet cable. Then use the Search Tool or APP to locate the camera on your smart

device, or HiP2P Client_Setup to locate the camera using your PC. (See note after "Wired Direct to PC Connection")

Wired Direct to PC Connection

Connect an Ethernet cable between the camera and your PC. Open your browser and enter the IP address-

192.168.1.88, username "admin", password "admin".

Note: By default, this camera obtains an IP address from a DHCP server on the local network. To find the IP

address of the camera, consult the DHCP client list on the DHCP server of your wireless router or use the

discovery tool (HiP2P Client_Setup_v6.0.3.2.exe) and follow the instructions found in the e-ipcam-swhno.zip

available on our website. However, if there is no DHCP server available, or if you are connecting the camera

directly with your PC without another device in-between, the static default IP address of this camera is

192.168.1.88.

Find using QR Code

The IPC View APP includes a QR code scanner. Open the IPC View on your smart device, click "+" in the upper right corner to

add a device, select the QR Code scanner and point your phone's camera at the QR code on the rear of the E-IPCAM-SWHNO.

The QR code will be automatically scanned and the camera will automatically be added. Click on the camera that was added in

the IPC View app and video from the camera will be streamed directly to the smart device.

If you change the password, be sure to make note of it. If you change the password and forget it, reset the camera to

default settings. Press and hold the "Reset" (see page 4) for 10 seconds, then release.

Sticker on the back of the E-

PCAM-SWHNO

NTI SOLAR PANEL IP CAMERA

APP Installation for Mobile Access

For Apple devices, download "IPC View" from the APP Store and install.

For Android devices, download "IPC View" from Google Play and install.

Run the "IPC View" and add devices using any of 3 methods:

1. Input the P2P ID (on the back of the camera (see sticker above)), User name, and Password of the camera manually. Then

click "Save"

2. Scan the QR code: Click the "Scan QR Code" button. At the bottom of the camera there is a label with the QR Code. Scan

this with a QR scanner on your smart phone. That will then reveal the ID. Enter the ID, Username and Password. Then click

"Save". (Once the scanner has picked up the QR code, on most phones the software will automatically load the ID, username

and password and establish connection to the camera. You only need to click on the loaded camera in the APP and the video

from the camera will be viewed.)

3. Click "Search". The local camera list will be displayed on your phone. Choose the camera to be viewed, enter the User name

and Password. Then click "Save"

Operation from Computer and LAN

1. If you haven't already, open the OCX_Setup.exe file. Follow the prompts to install this software. When it is done, click

"Finish".

2. Open the Search Tool application- "P2P Client".

3. Click the Settings button, it will prompt for a password for user admin, just click "OK". (There is no default password for this.)

Settings button

NTI SOLAR PANEL IP CAMERA

4. Place a checkmark in "Region" box in the right hand panel. Then click "Add Area" button. Enter a name for the area and

click "OK". The area will appear as a subdirectory under "Region".

5. Click the "Search" button. The local camera IP address and UID will be shown in the Search tool.

6. Place a checkmark in the check box to the left of the camera listed.

7. Click "Add". The camera UID should appear in the list to the right under "Region".

8. Make note of the IP address for the camera. (If your camera is directly connected to your PC, or if your router does not have a

DHCP server, then the IP address will be 192.168.1.88.

Once you have the IP address, you can move on to "Use with ENVIROMUX" on page 11 to setup using this

camera with your ENVIROMUX System.

This tool can be used to view video from the camera by selecting the camera icon between "IP CAMERA" and the "+" sign.

Note: This is not the software used to configure the camera. For camera configuration, continue with step 9.

Add Area button Area that is added will

appear under "Region"

Other manuals for ENVIROMUX Series

This manual suits for next models

Table of contents

Other NTI Security Camera manuals

NTI

NTI E-IPCAM-HNPO-P User manual

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications