Novus NVIP-H-8501/T User manual

NVIP-H-8501/T

NVIP-H-8511/T

NVIP-H-8521/T

NVIP-H-8531/T

NVIP-H-8541/T

Quick start guide

NVIP-H-85x1/T Quick start guide version 1.0

THE PRODUCT MEETS THE REQUIREMENTS CONTAINED IN THE FOLLOWING DIRECTIVES:

Exclusion of liability in the event of damage to data contained on disks or other devices or media:

The manufacturer is not liable in the event of damage or loss of data contained on disks or other

devices or carriers during the operation of the Product.

Obligation to consult the Manufacturer before performing any action not provided for in the

instruction manual or other documents:

Before performing an action that is not provided for a given Product in the user manual, other

documents attached to the Product or does not result from the normal purpose of the Product, it is

necessary, under pain of exclusion of the Manufacturer's liability for the consequences of such action,

to contact the Manufacturer.

CAUTIONS AND WARNINGS

Pictures in this publication showing camera views can be simulations. Actual camera

images may vary depending on the type, model, settings, observation area, or

environmental conditions.

DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIMENT AND OF THE

COUNCIL of 26 February 2014 on the harmonization of the laws of the Member States

relating to electromagnetic compatibility (OJ L 96, 29.3.2014, p. 79–106, with changes).

DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE

COUNCIL of 4 July 2012 on waste electrical and electronic equipment WEEE)

(OJ L 197, 24.7.2012, p. 38–71, with changes).

DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT AND OF THE

COUNCIL of 8 June 2011 on the restriction of the use of certain hazardous substances in

electrical and electronic equipment (OJ L 174, 1.7.2011, p. 88–110, with changes).

COMMISION DELEGATED DIRECTIVE (EU) 2015/863 of 31 March 2015 amending

Annex II to Directive 2011/65/EU of the European Parliament and of the Council as regards

the list of restricted substances.

DIRECTIVE (EU) 2017/2102 OF THE EUROPEAN PARLIAMENT AND OF THE

COUNCIL of 15 November 2017 amending Directive 2011/65/EU on the restriction of the

use of certain hazardous substances in electrical and electronic equipment.

NVIP-H-85x1/T Quick start guide version 1.0

1. Please read this manual carefully before installation and operation;

2. Please keep this manual for the lifespan of the device in case referring to the contents of this

manual is necessary;

3. It is necessary to comply with the safety requirements described in the manual, as they have a

direct impact on the safety of users and the durability and reliability of the device;

4. All activities performed by installers and users must be carried out as described in the manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. It is not allowed to use any additional devices, components or accessories not provided for and not

recommended by the manufacturer;

7. Do not install this device in places where proper ventilation cannot be provided (e.g. closed

cabinets, etc.), as this may cause heat build-up and may result in damage;

8. Do not place the device on unstable surfaces. Installation must be carried out by qualified

personnel with appropriate permissions in accordance with the recommendations provided in this

manual;

9. The device may be powered only from sources with parameters compliant with those indicated by

the manufacturer in the technical data;

SAFETY REQUIREMENTS

Before using the device, read the instruction manual in order to ensure proper and safe operation

of the device. Failure to comply with the instructions may lead to damage to the device and/or

safety violations.

The user may not repair the device himself. Repairs and maintenance of the device may only be

performed by qualified service personnel.

The device, which is an element of a professional CCTV system used for supervision and

control, is not intended for self-assembly in households by persons without specialist

knowledge.

As the product is constantly improved and optimised, some of its parameters and functions may have

changed from those described in this manual. If in doubt, please refer to the user manual at

www.novuscctv.com

The user manual located at www.novuscctv.com is always the most up-to-date version.

NVIP-H-85x1/T Quick start guide version 1.0

FOREWORD INFORMATION

1. TECHNICAL SPECIFICATION

IMAGE - THERMAL MODULE

Image Sensor Uncooled FPA Microbolometer

Number of Eecve Pixels 400 (H) x 300 (V)

Pixel Size 17 µm

Spectral Range 8 - 14 µm

Thermal Sensivity 40 mK

Thermovision Modes

White Hot, Black Hot, Rainbow, Ironbow, HSV, Autumn, Bone,

Cool, Copper, Fire Hot, Pink, Spring, Summer, Winter, Jet,

Flame, Rosebengal

Detecon Temperature -20°C ~ 150°C

Digital Noise Reducon (DNR) 2D, 3D

LENS - THERMAL MODULE

Lens Type

NVIP-H-8501/T: f=8 mm/F1.0

NVIP-H-8511/T: f=15 mm/F1.0

NVIP-H-8521/T: f=25 mm/F1.0

NVIP-H-8531/T: f=35 mm/F1.0

NVIP-H-8541/T: f=50 mm/F1.0

Object Detecon Range

NVIP-H-8501/T: 235m - human , 722m - vehicle

NVIP-H-8511/T: 441m - human , 1353m - vehicle

NVIP-H-8521/T: 735m - human , 2255m - vehicle

NVIP-H-8531/T: 1029m - human , 3137m - vehicle

NVIP-H-8541/T: 1471m - human , 4510m - vehicle

Object Recognion Range

NVIP-H-8501/T: 59m - human , 180m - vehicle

NVIP-H-8511/T: 110m - human , 338m - vehicle

NVIP-H-8521/T: 184m - human , 564m - vehicle

NVIP-H-8531/T: 257m - human , 789m - vehicle

NVIP-H-8541/T: 368m - human , 1127m - vehicle

NETWORK

Stream Resoluon 720 x 576 (D1), 352 x 288 (CIF)

Frame Rate 30 fps for each resoluon

Mulstreaming Mode 2 streams (main stream, sub stream)

Video/Audio Compression H.264, H.265/G.711, RAW_PCM

Number of Simultaneous Connecons max. 6

Bandwidth 8 Mb/s in total

Network Protocols Support HTTP, TCP/IP, IPv4/v6, UDP, HTTPS, FTP, DHCP, DNS, DDNS,

RTSP, RTP, SNMP, QoS, IEEE 802.1X, PPPoE, SMTP, RTCP

ONVIF Protocol Support Prole S

Camera Conguraon from Internet Explorer, Firefox, Chrome, Edge browser

languages: Polish, English, and others

Compable Soware NMS

NVIP-H-85x1/T Quick start guide version 1.0

FOREWORD INFORMATION

OTHER FUNCTIONS

Temperature Measurement yes

Temperature Alarm yes

Temperature Measurement Zones 20 polygon, line, point

Temperature Measurement Accuracy +-2°C / +-2%

Privacy Zones 4 video mask type: single color

Moon Detecon yes

Audio Detecon yes

Video Content Analysis (VCA)

abandoned object, object disappearance, line cross, zone

entrance, zone exit, double line cross, loiter, converse,

pedestrian detecon, people counng, vehicle detecon,

human body temperature mesuring, intrusion detecon,

smoker detecon, re detecon

Prealarm/Postalarm up to 5 MB/up to 86400 s

System Reacon to Alarm Events e-mail, saving le on FTP server, saving le on SD card, alarm

output acvaon

Restoring default sengs using reset buon

INTERFACES

Audio Input/Output 1/1

Alarm Input/Output 2 (NO/NC)/2

RS-485 yes

Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

Memory Card Slot SD - capacity up to 128GB

INSTALLATION PARAMETERS

Dimensions (mm) with bracket: 110 (Ф) x 388 (L)

Weight 1.9 kg

Degree of Protecon IP 66 (details in the user’s manual)

Enclosure aluminium, white, fully cable managed wall mount bracket in-

set included

Power Supply 12 VDC, PoE (IEEE 802.3af, Class 3)

Surge protecon TVS 4000 V

Power Consumpon 6 W

Operang Temperature -40°C ~ 60°C

Humidity max. 90%, relave (non-condensing)

NVIP-H-85x1/T Quick start guide version 1.0

1.1. Camera dimensions (given in mm)

1.2. Package contents

After you open the package make sure that the following elements are inside:

• Thermal IP camera

• Mounting Base (Wall/Ceiling Adapter)

• Bag with mounting accessories

• Mounting template

• Focusing wrench/screws (depending on model)

• Quick Start Guide

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

Caution:

If the device was brought from a room with a lower temperature, wait until it reaches the

temperature of the room in which it is to work. Do not switch the device immediately after

bringing from a cooler place. The condensation of water vapor can cause short circuits and

consequently damage the device.

2. START-UP AND INITIAL CONFIGURATION

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

FOREWORD INFORMATION

NVIP-H-85x1/T Quick start guide version 1.0

2.1. Description of the camera's electrical connectors

All camera sockets and connectors are located in a special connector block, integrated with the camera

foot.

START-UP AND INITIAL CONFIGURATION

No Name Funcon Descripon

1COM OUT 1 Ground Alarm output 1 ground

2ALARM OUT1 Alarm output 1 Alarm output 1, relay

GroundCOM IN13Alarm input 1 ground

Alarm input 1 Alarm input 1, congurable NO/NCALARM IN14

Audio inputAUDIO IN5Audio line input

6AUDIO GND Ground Audio input and output ground

7AUDIO OUT Audio output Audio line output

8NC Not used

9NC Not used

10 COM OUT2 Ground Alarm output 2 ground

11 ALARM OUT2 Alarm output 2 Alarm output 2, relay

12 COM IN2 Ground Alarm input 2 ground

13 ALARM IN2 Alarm input 2 Alarm input 2, congurable NO/NC

14 RS485+ RS485 port PTZ camera control

15 RS485- RS485 port PTZ camera control

16 DC12V/AC24V Power socket Camera power supply, +12VDC or 24VAC

17 DCGND/AC24V Power socket Camera power supply, ground (GND) or 24VAC

18 LAN RJ-45 port Network port, 10/100 MB/s, PoE power supply

19 Earth clamp Noiseless grounding (oponal connecon)

NVIP-H-85x1/T Quick start guide version 1.0

2.2. Connection of alarm input and output

2.3. Power connection

The camera can be powered from one of the DC power adapters available on the market, provided that

it meets the camera's technical requirements. The power supply must provide a stabilized DC voltage of

12V, must allow the consumption of at least 10W of power, and allow for connection to the camera

using bare wires.

The camera can also be powered from a 230V/24V transformer or from an AC power supply supplying

24VAC/50Hz. The transformer or power supply must allow the consumption of at least 10W of power,

and allow the connection to the camera using bare wires.

Connect the wires to the power plug and then insert the plug into the power socket.

It is also possible to power the camera through the RJ45 network socket, using PoE technology (IEEE

802.3af Class 3).

Caution!

It is forbidden to use PoE devices (power supplies, adapters, etc.) that are not compliant with the

IEEE 802.3at standard, commonly referred to as "passive PoE power supplies", as the camera's

power source. Damage resulting from the use of inappropriate power sources is not covered by

the warranty.

2.4 Protection against water ingress

The declared tightness class of the camera applies to its housing and the mounting base (wall/ceiling

adapter), which is part of the equipment, provided that the correct installation is performed in

accordance with the procedure specified in section 2.5 of the manual. It is the responsibility of the

person installing the camera to protect the elements that require it against moisture.

The manufacturer is not responsible for any damage to the camera resulting from failure to comply

with the above-mentioned obligation, which at the same time means that they are not subject to

warranty repairs.

START-UP AND INITIAL CONFIGURATION

Alarm input connecon diagram

ALARM IN

COM IN

Alarm output connecon diagram

ALARM OUT

COM OUT

NVIP-H-85x1/T Quick start guide version 1.0

2.5. Camera mounting

 Place the mounting template on the mounting location so that the "UP" symbol and the arrow

point vertically upwards, mark the places for the holes for the wall plugs and the hole for the

connection cables (if necessary). Drill holes, insert wall plugs

 Depending on the planned method of leading the connecting cables, adjust the position of the

plugs and the gland in the holes of the base

 Screw the mounting base (wall/ceiling adapter) to the mounting location so that the arrow

embossed in its bottom points upwards. Run the wires through the hole in the back wall (if

necessary) and, after screwing the base, seal the space around them with sealing compound.

Alternatively, lead the wires through the gland and tighten the gland tightly

 Connect the cables to the appropriate sockets located in the connector block in the foot of the

camera. Place the camera foot on the mounting base with the "UP" embossed on the top of the

foot facing up. Tighten the screws securing the foot to the base.

START-UP AND INITIAL CONFIGURATION

When bolting the base to the mounting location, ensure that all screw head slots have gaskets.

Before starting the installation, plan how to route the connection cables, bearing in mind that the

mounting base (wall/ceiling adapter) allows cables to be inserted from the back (through the

wall), from the bottom or from the right side.

Cables may enter the mounting base (wall/ceiling adapter) only through the cable gland (except

for the hole in the rear panel - see next point). All other unused openings must be sealed with

plugs.

When mounting the camera on the mounting base, pay attention to the correct positioning of the

gasket in the foot. The seal must not be damaged, it must be located in the groove of the foot and

after screwing the camera it must adhere to the base around the entire perimeter.

NVIP-H-85x1/T Quick start guide version 1.0

 Adjust the camera position and focus to obtain the desired field of view.

To set the observation field, loosen the screws A and B, set the camera in the desired position and

tighten the screws fully.

Focus adjustment is performed as follows: screw the special screws included in the accessories into

the holes in the ring around the lens. Using the screws as handles, gently rotate the ring until it is

sharp enough. After completing the adjustment, the screws should be removed.

START-UP AND INITIAL CONFIGURATION

This manual suits for next models

Table of contents

Languages:

Other Novus Security Camera manuals

Novus

Novus NVIP-2DN3033V/IR-1P User manual

Novus

Novus NVIP-4H-6201-II User manual

Novus

Novus NVIP-5V-6401/F User manual

Novus

Novus NVIP-8H-6202M User manual

Novus

Novus NVAHD-1DN5102D/IR-1 User manual

Novus

Novus NVIP-3SD-6300/30/F User manual

Novus

Novus NVIP-2H-6632M User manual

Novus

Novus NVAHD-1DN3102SD/IR-1 User manual

Novus

Novus NVIP-5VE-6401/F User manual

Novus

Novus NVIP-2VE-4231 User manual

Novus

Novus NVIP-2DN3030H/IR-1P-II User manual

Novus

Novus NVIP-2DN3032V/IR-1P User manual

Novus

Novus NVIP-6DN5060V/IRH-2P User manual

Novus

Novus NVIP-1DN3000H/IR-1P User manual

Novus

Novus NVIP-2H-6601 User manual

Novus

Novus NVIP-4C-6500/F User manual

Novus

Novus NVIP-2H-6232-II User manual

Novus

Novus NVIP-3DN7540H/IRH-2P User manual

Novus

Novus NVAHD-4DN3202V/IR-1 User manual

Novus

Novus NVIP-2V-6501/F-II User manual

Novus

Novus NVAHD-2DN5504MV/IR-1 User manual

Novus

Novus 6000 VSS MULTI HD User manual

Novus

Novus NVIP-2DN2101V/IR-1P User manual

Novus

Novus NVIP-5H-4202M User manual

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications