Nordson Encore PE User manual
Instruction Sheet
Part 1604293−01
E2013 Nordson Corporation
P/N 1604293-01
EncorerPE 50-lb Feed Hopper
WARNING: Allow only qualified personnel to perform the following tasks. Follow
the safety instructions in this document and all other related documentation.
Description
This instruction sheet provides specifications; installation and operation
instructions; and parts lists for the Encore PE 50-lb Feed Hopper.
This hopper is used primarily with Nordson Mobile or Rail Mount Manual Powder
PE Spray Systems. The hopper is shipped fully assembled, with an Encore PE
pump adapter and pickup tube assembly, vent tube, and hopper fill plug.
Specifications
Specification Value
Powder Capacity: 23 kg (50 lb)
*Pump Knockouts: 2
*Pump Adapters Included: 1
Dimensions
Height: 62 cm (24.5 in.)
Diameter: 40.00 cm
(15.75 in.)
Weight (Empty): 9.5 kg (21 lb)
Weight
(Full to Capacity):
32.5 kg (71 lb)
Fluidizing Pressure: 0.1−0.6 bar
(2−8 psi)
Fluidizing Air Tubing: 10-mm OD
*Pumps and additional adapters must be ordered separately.
Encore PE 50-lb Feed Hopper
2
Part 1604293−01 E2013 Nordson Corporation
Installation
Basic
See Figure 1.
1. Make sure the fluidizing drum (6) and cover (2) are securely clamped to the
body (3), and that all gaskets are undamaged and sealing properly.
2. Connect 10-mm flexible air tubing to the fitting labeled with the fitting on the
rear of the controller labeled with the hopper fluidizing icon ( ). Connect the
opposite end of the tubing to the fluidizing air connector (5).
WARNING: All electrically conductive equipment in the spray area must be
grounded. Ungrounded or poorly grounded equipment can store an electrostatic
charge which can give personnel a severe shock or arc and cause a fire or
explosion.
3. For stand-alone hoppers, connect the ground wire shipped with the hopper to
the ground stud (4). Connect the spring clip to a true earth ground.
For hoppers on a mobile powder system dolly, connect the dolly ground wire to
the ground stud (4).
4. Make sure the O-rings are installed correctly in the pump or adapter grooves.
Install the pump on or in the adapter with a slight twisting motion.
5. Connect the flexible vent hose shipped with the hopper to the vent hose
adapter (1). Secure the hose to the adapter with a hose clamp. Connect the
other end of the hose to the booth powder collector to prevent vented powder
from contaminating the room air.
Installing Additional Pumps
If you wish to install an additional pump, you must order a pump adapter and
pickup tube for it. Remove the plug from the cover and install the adapter, pickup
tube, and pump.
3
Encore PE 50-lb Feed Hopper
Part 1604293−01
E2013 Nordson Corporation
12
3
4
6
5
Figure 1 NHR-2-50 Encore PE Feed Hopper
1. Vent hose adapter
2. Cover
3. Body
4. Ground stud
5. Fluidizing air connector
6. Fluidizing drum
Operation
WARNING: Wear an approved respirator, protective clothing, and gloves when
handling powder. Avoid skin contact with powder coatings, or breathing powder
particles.
1. Fill the hopper half full of powder, to provide room for expansion as the powder
is fluidized. Do not overfill. Overfilling may prevent powder from being fully
fluidized, and affect coating performance.
2. Turn on the fluidizing air, and adjust the regulator until the powder is gently
“boiling.” The air mixed with the powder will cause it to increase in volume.
Fluidize the powder for five or ten minutes to make sure it is evenly fluidized
and no clumps are left before spraying.
Maintenance
Periodically, empty the hopper and clean the interior. Clean the fluidizing plate and
inspect it for signs of air contamination. If the plate is discolored and appears to be
contaminated, replace it. Check your air supply and correct any contamination
problems.
Encore PE 50-lb Feed Hopper
4
Part 1604293−01 E2013 Nordson Corporation
Parts
To order parts, call the Nordson Industrial Coating Systems Customer Service
Center at (800) 433-9319 or your local Nordson representative.
See Figure 2.
Item Part Description Quantity Note
1604292 HOPPER ASSEMBLY, NHR Encore PE, 50 lb., packaged 1
1 1008082 SHOSE, flexible, 3 m (10 ft) 1
2 970966 SCLAMP, hose 1
3 1070232 SPLATE, fluidizing 1
4 1070234 SGASKET, U-channel 1
5 1074531 SDRUM, fluidizing 1 A
6 1107948 SBODY, hopper, packaged, 50 lb 1
7 981170 SS SCREW, truss, unslotted, 10−32 x 0.375 in. 8
8 984120 SS NUT, hex, small pattern, 10−32 8
9 164064 SS LATCH, hopper, curve base 4
10 1074532 SCOVER, hopper, NHR-2, assy, packaged 1 B
11 1602284 SMOUNT ASSY, pump, 18 in. 1
12 942161 SS O-RING, silicone, 1.125 x 1.375 x 0.125 in. 1
13 1602261 SS MOUNT, pump 1
14 309474 SS TUBE, pickup, 0.490-in. ID x 18 in., ⅜NPS 1
15 939613 SS LOCKNUT, conduit, 3/4-in. NPS 1
16 142342 SS Plug 1
NS 134575 SWIRE, ground 1
NOTE A: Refer to Fluidizing Drum on page 7 for a parts breakdown.
B: Refer to Hopper Cover on page 6 for a parts breakdown.
NS: Not Shown
5
Encore PE 50-lb Feed Hopper
Part 1604293−01
E2013 Nordson Corporation
3
6
10
2
1
4
5
11
7
8
9
13
12
15
14
16
Figure 2 Hopper Parts
Encore PE 50-lb Feed Hopper
6
Part 1604293−01 E2013 Nordson Corporation
Hopper Cover
Item Part Description Quantity Note
— 1074532 COVER, hopper, NHR-2 assy, packaged 1
1 1008081 SNUT, conduit, 1.25 in. 1
2 1008080 SGASKET, vent stack 1
3 1008079 SFITTING, pvc, 1 1/4in., male adapter 1
4 1070199 SPLUG, hopper fill, NHR 1
NS 1074539 GASKET COVER SERVICE KIT 1
NS: Not Shown
1
3
24
Figure 3 Hopper Cover
7
Encore PE 50-lb Feed Hopper
Part 1604293−01
E2013 Nordson Corporation
Fluidizing Drum
Item Part Description Quantity Note
— 1074531 DRUM, fluidizing 1
1 1074535 SELBOW, male, 3/8-in. RPT x 10-mm tube 1
2 984702 SNUT, hex, M5, brass 2
3 983401 SLOCK WASHER, split, M5, steel, zinc 11
4 983021 SWASHER, flat, 0.203 x 0.405 x 0.040 in., brass 1
5 982126 SSCREW, pan head, M5 x 25, brass 1
6 240674 STAG, ground 1
7 164064 SLATCH, hopper, curve base 4
8 982000 SSCREW, pan head, M5 x 10, zinc 8
9 983123 SWASHER, flat, 0.219 x 0.500 x 0.049 in. 7
10 984706 SNUT, hex, M5, steel, zinc 8
5
3
3
2
4
3
2
1
8
9 3 10
7 6
Figure 4 NHR Fluidizing Drum
Encore PE 50-lb Feed Hopper
8
Part 1604293−01 E2013 Nordson Corporation
Issued 7/13
Original copyright date 2013. Encore, Nordson, and the Nordson logo are registered trademarks of Nordson Corporation.
Other manuals for Encore PE
1
This manual suits for next models
1
Table of contents
Other Nordson Paint Sprayer manuals
Nordson
Nordson A7A Reference guide
Nordson
Nordson HSS User manual
Nordson
Nordson Trilogy User manual
Nordson
Nordson Versa-Spray User manual
Nordson
Nordson Encore Series Reference guide
Nordson
Nordson HORIZON 200 User manual
Nordson
Nordson Encore HD Reference guide
Nordson
Nordson ColorMax Parts list manual
Nordson
Nordson WM-1 Reference guide
Nordson
Nordson PRODIGY Reference guide
Nordson
Nordson ColorMax 2 Reference guide
Nordson
Nordson Encore HD Reference guide
Nordson
Nordson Encore Reference guide
Nordson
Nordson Encore User manual
Nordson
Nordson SCF-M1 User manual
Nordson
Nordson Encore LT Automatic Reference guide
Nordson
Nordson Encore User manual
Nordson
Nordson Vantage Reference guide
Nordson
Nordson kinetix User manual
Nordson
Nordson Corona Cup Gun Ki User manual
Popular Paint Sprayer manuals by other brands
zogics
zogics Z-DAS instruction manual
KISANKRAFT
KISANKRAFT KK-KBS-165 Operation manual
Matrix
Matrix SG 650 Translation of the original instructions
Anest Iwata
Anest Iwata SGA-3 Installation, use & maintenance instruction manual
paasche
paasche VV Instructions and parts list
Carlisle
Carlisle DeVilbiss JGA-510 Service manual
