Nordson HSS User manual

Equipment required:

a Filled cartridges (Ratio-Pak®cartridges shown)

b HSS static mixer spray nozzle and air regulator kit

c HSS pneumatic spray gun

Note: To use Film-Pak®collapsible cartridges,

order a gun with built-in retainers or use

removable retainers with an existing gun.

If recommended by the product manufacturer,

pre-heat the cartridge for 1–2 hours at 32–38° C

(90–100°F). Do not exceed 49° C (120° F), as this

will affect the integrity of the cartridge.

Important: Consult with the product manufacturer

to determine whether shaking is required. If

shaking is required, gently agitate / shake new or

partially used cartridges for at least two minutes

prior to application.

Remove the retaining nut, compression disc, and

end cap(s) from the cartridge outlet.

High Solid Spray (HSS) System

Instructions

100°

90°

38°

32°

C F

If required, insert a ow restrictor.

Note: Some products require the use of a ow

restrictor to equalize material ow. Flow restrictors

are ordered separately. Contact your Nordson EFD

representative for the proper ow restrictor and for

installation assistance.

Seat an HSS static mixer spray nozzle on the

cartridge outlet, ensuring that the bell housing sits

ush on the tip of the outlet. If required, install a

retaining nut.

Note: Integral nut mixers do not require a retaining

nut; bell mixers do require a retaining nut.

End cap

Retaining nut

1 2

3 4

5 6

a b

High Solid Spray (HSS) System Instructions

For Nordson EFD sales and service in over

40 countries, contact Nordson EFD or go to

www.nordsonefd.com.

800-556-3484; +1-401-431-7000

[email protected]

Attach the air line of the HSS air regulator kit to the

HSS static mixer spray nozzle.

On the HSS regulator, place the ball valve lever (a)

in the closed position; then connect the plant air

supply (b) to the HSS regulator.

Point the gun up (a) and slowly dispense material

into the static mixer. Then dispense the rst 15 cm

(6") of unmixed material into a waste container (b).

Perform this process for each new or partially used

cartridge.

Important: Before increasing the uid pressure, verify that both material

components are traveling equally through the mixer. As needed, dispense

unmixed material into a waste container.

With the ball valve lever (a) in the closed position, set the HSS regulator (b) to

1.7bar(25psi); then slowly move the ball valve lever to the open position to

supply the spray nozzle with atomizing air. Adjust the HSS regulator and ball

valve lever until the desired operational settings are achieved.

Depending on the material, the material temperature, and the desired nish,

adjust the uid pressure regulator knob on the gun (c) as needed.

If applicable, hand-tighten the retaining nut

securely on the cartridge outlet threads (do not

over-tighten).

Insert the cartridge (or cartridge / retainer — not

shown) in the dispense gun, referring to the

applicable dispense gun instructions as needed.

7 8

9 10

a b

Point the cartridge up

Fluid pressure regulator

knob on the dispense gun

On the dispense gun, turn the uid pressure

regulator knob counterclockwise until it will no

longer turn; then turn the knob 1–2 rotations

clockwise.

Note: Steps 11–12 purge air from the cartridge.

Fluid pressure adjustmentHSS regulator air pressure

adjustment

Ball valve

lever

Dispense unmixed material

Other Nordson Paint Sprayer manuals

Nordson

Nordson FP-200 User manual

Nordson

Nordson Sure Coat Series Reference guide

Nordson

Nordson A7A Reference guide

Nordson

Nordson MicroMax 2 User manual

Nordson

Nordson Encore HD User manual

Nordson

Nordson Encore Series Reference guide

Nordson

Nordson Encore XT Reference guide

Nordson

Nordson Mastic Gun Reference guide

Nordson

Nordson Encore HD Reference guide

Nordson

Nordson Trilogy GP Reference guide

Nordson

Nordson Tribomatic II Reference guide

Nordson

Nordson SCF-M1 User manual

Nordson

Nordson Trilogy User manual

Nordson

Nordson HORIZON 200 User manual

Nordson

Nordson Trilogy Reference guide

Nordson

Nordson kinetix Reference guide

Nordson

Nordson A7A Reference guide

Nordson

Nordson Encore LT Automatic Reference guide

Nordson

Nordson Versa-Spray II Reference guide

Nordson

Nordson ColorMax Parts list manual

Nordson

Nordson ColorMax User manual

Nordson

Nordson A7A Reference guide

Nordson

Nordson PRODIGY Reference guide

Nordson

Nordson Encore Reference guide

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Graco

Graco 246737 Repair and parts

Binks

Binks SV100 Service manual

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

Graco

Graco EM 390 Instructions-parts list

DeVilbiss

DeVilbiss LUNA2i Operation manual

Graco

Graco HydroShield WMBH00 Instructions - parts