Norac UC5 Topcon X30 User manual

UC5 Height Sensor, Roll Sensor and

Linear Sensor Testing

Printed in Canada

Reorder P/N: 54645-MAN Revision C

NOTICE

NORAC Systems International Inc. reserves the right to improve products and their specifications

without notice and without the requirement to update products sold previously. Every effort has

been made to ensure the accuracy of the information contained in this manual. The technical

information in this manual was reviewed at the time of approval for publication.

Contents

1Introduction.........................................................................................1

254645 – UC5 Resource Upgrade Kit .................................................2

354646 – UC5 Resource Kit .................................................................4

4Calibration Stand Assembly and Alignment....................................6

5Height Sensors ....................................................................................9

6Roll Sensors .......................................................................................16

7Linear Sensors...................................................................................19

8Frequently Asked Questions ...........................................................21

9Height Sensor Log Sheet .................................................................22

10Roll Sensor Log Sheet ......................................................................25

11Linear Sensor Log Sheet..................................................................26

12Appendix A – Adjusting 44730 Calibration Stand.........................27

1Introduction

This manual serves as an instruction manual for testing UC5 height sensors, roll

sensors and linear sensors. This procedure is useful in determining if a product

needs to be returned to NORAC for repairs or if it is possible to continue

using it. This procedure also provides a method for performing some basic

calibration of the UC5 height sensor to improve its performance.

Phone: 1-800-667-3921 Canada (Toll Free)

1-866-306-6722 United States (Toll Free)

(+33) (0)4 26 47 04 42 Europe

1-306-664-6711 all other regions

E-mail: [email protected]

Web Site: www.norac.ca

254645 – UC5 Resource Upgrade Kit

2.1 Parts List

Table 1: Items included in the UC5 Resource Kit Upgrade

Item Part Number Name Quantity

C01 44644-08 CABLE BUSMONITOR (DT FEMALE TO AMP MALE) 1

E01 54731 UC5 TOOLSUITE CD 1

E03 43764T UC5 NETWORK COUPLER 2-WAY WITH TERMINATOR REV-A 1

M01 54645-MAN MANUAL UC5 SENSOR TESTING 1

NOTE: This kit must be used in conjunction with the UC4 Resource

Kit (NORAC Part Number 44645).

Table 2: Items included in the UC4 Resource Kit and Available for Re-order from

NORAC

Item Part Number Name Quantity

*M05 106127 ADH RTV 162 WHITE SILICONE - 85mL TUBE 1

M06 44645-02 TRANSDUCER SERVICE KIT 1

M07 44645-03 O-RING SERVICE KIT 2

M08 44645-04 FOAM DISC SERVICE KIT 1

** Item M05 is available for re-order from NORAC, as well as from the

manufacturer:

Item # Description

Manu

acturer

Part #

M05 ADH RTV 162 WHITE

SILICONE - 85mL TUBE

MG Chemicals

/Momentive

RTV162-

85mL

2.2 PC Requirements

1. Operating System: Windows XP, Windows Vista or Windows 7.

2. Microsoft .NET Framework: Version 4.0 or higher.

2.3 Software Installation

1. Insert the included UC5 Toolsuite CD into the disk drive.

2. Double-click the UC5 Toolsuite .exe file and follow the prompts to install.

3. A shortcut to the program is placed in the Start Menu.

2.4 Cable Connections

1. Connect the USB-to-Serial Adapter to the computer.

2. Connect the Bus Monitor’s connector labeled “To CANbus” to the Stand-

Alone Power Cable connector labeled “To Bus Monitor”.

3. Connect the Stand-Alone Power Cable to a 12VDC power supply. The

red banana plug must be connected to the positive terminal and the black

banana plug to the ground.

4. Switch the power supply on, check that the LED on the Bus Monitor is

illuminated and switch off power supply.

5. Connect the 4-pin AMP receptacle (R4) on 44644-08 (C01) to the AMP

connector on the Bus Monitor labeled “To CANbus”.

6. Connect the 2-way terminator (43764T [E03]) to the 6-pin Deutsch plug

on 44644-08 (C01).

Figure 1: NORAC Bus Monitor Connections

Figure 2: 44644-08

Power

Suppl

Connect to C01

Serial

–

USB

Adapter

CANbus

Connector

Bus

Monitor

Stand Alone

Power Cable

354646 – UC5 Resource Kit

3.1 Parts List

Table 3: Items included in the UC5 Resource Kit

Item Part Number Name Quantity

B01 44968 ULTRASONIC SENSOR CALIBRATION FIXTURE TYPE2 1

C01 44644-11 CABLE BUS MONITOR PEAK PCAN TEE (MALE & FEMALE DT) 1

C02 43250-12 CABLE UC5 BATTERY PIGTAIL (ECU AND SIGNAL POWER) 1

E01 106359 CAN BUS MONITOR (PEAK PCAN-USB) 1

E02 54731 UC5 TOOLSUITE CD 1

E03 43764T UC5 NETWORK COUPLER 2-WAY WITH TERMINATOR 1

M01 54645-MAN MANUAL UC5 RESOURCE KIT 1

**M05 106127 ADH RTV 162 WHITE SILICONE - 85mL TUBE 1

*M06 44645-02 TRANSDUCER SERVICE KIT 1

*M07 44645-03 O-RING SERVICE KIT 2

*M08 44645-04 FOAM DISC SERVICE KIT 1

* Items M06, M07 and M08 are available for re-order from NORAC.

** Item M05 is available for re-order from NORAC, as well as from the

manufacturer:

Item # Description

Manufacturer

Part #

M05 ADH RTV 162 WHITE

SILICONE - 85mL TUBE

MG Chemicals

/Momentive

RTV162-

85mL

3.2 PC Requirements

1. Operating System: Windows XP, Windows Vista or Windows 7.

2. Microsoft .NET Framework: Version 4.0 or higher.

3.3 Software Installation

1. Insert the PEAK System CD into the disk drive. After selecting a language,

select the Drivers button. Select the PCAN-USB driver and click Install

Now. Follow the prompts to install.

2. Insert the included UC5 Toolsuite CD into the disk drive. Double-click

the UC5 Toolsuite .exe file and follow the prompts to install.

3. A shortcut to the program is placed in the Start Menu.

3.4 Cable Connections

1. Connect 44644-11 (C01) to the bus monitor. Connect 43250-12 (C02) to

the 6-pin receptacle on 44644-11. Connect the 2-way terminator (43764T

[E03]) to the 6-pin plug on 44644-11.

2. Connect the pigtail end of 43250-12 to a 12 VDC (2A or greater) power

supply. Ensure the in-line fuse is connected to the positive terminal and

the black wire is connected to the negative terminal.

3. Connect the bus monitor to the computer’s USB port.

Figure 3: PEAK Bus Monitor Connections

To Power

Suppl

PEAK

CANbus

Monitor

44644-11

(C01)

43250-12

(C02)

43764T

(E03)

4Calibration Stand Assembly and Alignment

1. Assemble the two parts of the test stand as shown in Figure 4. Insert the

sheet metal insert into the rectangular hole. Install the spring, flat washer

and wing nut onto the stud. Tighten wing nut until the spring is

approximately half compressed.

Figure 4: Test Stand Assembly

457 mm

(18”)

2. Insert the alignment tool (44968-2) into the test stand. (Figure 5)

3. Adjust the threaded mount (A) of the golf ball target so the surface of the

ball will touch the tip of the alignment tool (it may be necessary to align

the calibration stand first (Step 4) before this is possible.

4. Using the adjustment screws (B and C), align the tip of the alignment tool

to the center of the golf ball.

To move the tip of the rod upwards, turn both adjustment screws in an

equal amount.

To move the tip of the rod downwards, turn both adjustment screws

out an equal amount.

To move the tip of the rod side to side, turn one screw in and one

screw out an equal amount.

5. Rotate the alignment tool 180 degrees and repeat the alignment process

(Step 4). If after rotating the alignment tool the tip of the rod is not

centered on the ball target, split the difference of the two calibrations.

6. It may be necessary to adjust the threaded mount of the ball target (A)

after Step 5.

Figure 5: Test Stand Alignment

Other manuals for UC5 Topcon X30

Table of contents

Popular Control System manuals by other brands

Pentair Pool Products

Pentair Pool Products Compool Installation and user guide

ComfortNET

ComfortNET CTK04 manual

Fireye

Fireye InSight II 95DSS3 manual

CAME

CAME G3000 installation manual

Idemia

Idemia MorphoAccess VP MD installation guide

Axis

Axis P1445-LE-3 user manual

HEIDENHAIN

HEIDENHAIN TNC 150 B manual

CNC-Step

CNC-Step High-Z T-Series operating instructions

Doosan

Doosan DVF Series Operation user's manual

Honeywell

Honeywell KAP 140 Maintenance manual

Honeywell

Honeywell vk41 series Handbook

AirBench

AirBench FPW Operation and maintenance

Cypress

Cypress HHR-3160 product manual

CAME

CAME GLT40AOS installation manual

Zonex

Zonex GEN II -VVT Installation and application manual

Altronics

Altronics K 9650 quick start guide

micro-trak

micro-trak RoadMaster Reference manual

micro-trak

micro-trak Calc-An-Acre II Reference manual