Nice HySecurity TITAN 912L Series Installation and operating manual
Installation Reference Manual
IMPORTANT!
These instructions apply only to the 912L actuator.
Control box installation/operation is described in a separate control box manual.
TITAN12L/12L1 912L actuator
912L LA
Vehicular swing gate actuator
TITAN 912L Actuator
INSTALLATION REFERENCE MANUAL
2hysecurity.com • 800-321-9947 MX4685 Rev. C ©2019
LIST OF INSTRUCTIONS
INSTRUCTION 1A: INSTALL PIVOT ARM TO GATE (PULL-TO-OPEN) ............. 5
INSTRUCTION 1B: INSTALL PIVOT ARM TO GATE (PUSH-TO-OPEN) ............. 6
INSTRUCTION 2: MOUNT ACTUATOR TO PIVOT ARM ................................... 7
INSTRUCTION 3: AFFIX GATE BRACKET TO ACTUATOR ARM ....................... 8
INSTRUCTION 4: POSITION GATE BACKET ON GATE .................................... 9
INSTRUCTION 5: AFFIX GATE BRACKET TO GATE ......................................... 10
INSTRUCTION 6: OPEN MECHANICAL RELEASE .............................................11
INSTRUCTION 7: MANUALLY SET GATE OPEN/CLOSE LIMITS ..................... 12
INSTRUCTION 8: RUN ACTUATOR CABLE(S) TO CONTROL BOX ..................13
INSTRUCTION 9A, 9B, 9C, 9D: WIRE ACTUATOR TO CONTROIL BOARD ....14
INSTRUCTION 10A, 10B: SETTING ACTUATOR FINE LIMITS ..........................18
INSTRUCTION 11: ACTUATOR CABLE/TERMINAL WIRING ........................... 19
CONTENTS
LIST OF INSTRUCTIONS ......................................................................2
SECTION 1: TITAN 912L ACTUATOR OVERVIEW ............................3
SECTION 1: TOOLS NEEDED FOR INSTALLATION ........................4
SECTION 2: INSTALLATION SAFETY ................................................4
SECTION 3: ACTUATOR - MECHANICAL INSTALLATION .............5
3.1 MANUALLY SET GATE OPEN/CLOSE LIMITS .....................12
3.2 RUN ACTUATOR CABLE(S) TO CONTROL BOX .................13
3.3 936 CONTROL BOARD WIRING: PULL-TO-OPEN ..............14
3.4 936 CONTROL BOARD WIRING: PUSH-TO-OPEN .............15
3.5 1050 CONTROL BOARD WIRING: PULL-TO-OPEN ............16
3.6 1050 CONTROL BOARD WIRING: PUSH-TO-OPEN ...........17
3.7 SETTING ACTUATOR FINE LIMITS .......................................18
3.8 ACTUATOR CABLE REPLACEMENT WIRING ...................... 20
SECTION 4: PART DRAWINGS ........................................................ 21
TITAN 912L Actuator
INSTALLATION REFERENCE MANUAL
3
MX4685 Rev. C ©2019 hysecurity.com • 800-321-9947
• TITAN 912L-1 = Actuator with 12’ harness
• TITAN 912L-2 = Actuator with 42’ harness
(dual gate only)
PIVOT ARM (P/N 1116)
ACTUATOR BOLT KIT
(P/N 1125)
GATE BRACKET,
BLACK
(P/N 10025215)
TITAN912L ACTUATOR PARTS IDENTIFICATION
PART# DESCRIPTION QTY
912L-1 ACTUATOR WITH 12 FOOT HARNESS 1
912L-2 (DUAL GATE ONLY) ACTUATOR WITH 42 FOOT HARNESS 1
1116 PIVOT ARM 1
10025215 or PD0959A0000 GATE BRACKET (BLACK) 1
1125 ACTUATOR BOLT KIT 1
TITAN912L ACTUATOR SPECIFICATIONS
DRIVE Electromechanical Stainless Steel Screw
GATE LENGTH and WEIGHT MAX. • Up to 600 lb. for 20 foot leaf (272 kg for 6 m)
• Up to 1000 lb for an 8 ft leaf (453 kg for 2.4 m)
OPEN/CLOSE TIME (TO 90°) 14 - 16 seconds (adjustable)
TEMPERATURE RATING -4º to 122º F (-20º to 50º C)
OPERATING VOLTAGE 12VDC
ACTUATOR DIMENSIONS 43(L) x 4(W) x 6.75 inches (D)
[109.2(L) x 10(W) x 17.5 cm (D)]
USER CONTROLS 936 or 1050 control board
LISTED TO UL325 936 & 1050 Control Boards: Usage Class I, II, III, IV
ACTUATOR WEIGHT 19.75 lb (8.96 kg)
Congratulations on selecting a Nice TITAN 912L actuator. With proper selection, system design, installation
and maintenance this operator should provide years of reliable operation. This manual covers ONLY the instal-
lation of the actuator.
IMPORTANT!
For control box installation, wiring, operation, maintenance instructions and all safety information, refer to the
appropriate control box installation manual used for the system:
• CBOX936 (with 936 control board)
• CBOX1050 (with 1050 control board)
• MB1050 (with 1050 control board, integral batteries, and AC-DC power supply)
SECTION 1: TITAN 912L ACTUATOR OVERVIEW
TITAN 912L Actuator
INSTALLATION REFERENCE MANUAL
4hysecurity.com • 800-321-9947 MX4685 Rev. C ©2019
• DISCONNECT POWER AT THE CONTROL PANEL BEFORE MAKING ANY ELECTRIC SERVICE POWER
CONNECTIONS.
• BE AWARE OF ALL MOVING PARTS AND AVOID CLOSE PROXIMITY TO ANY PINCH POINTS.
Below is a list of tools necessary for installation of the Titan actuator:
• Welder (for pivot arm) unless optional bolt-on pivot arm (P/N 446) is used.
• Basic hand tools (screwdrivers, wrenches, pliers, etc..)
• Torx 25 tool (for removing actuator cover screws)
• Level (for ensuring pivot arm and actuator are level).
• Framing square (for determining pivot arm location)
• Torch/Chop Saw (for cutting pivot arm)
• Grinder (for sanding Pivot Arm)
IMPORTANT!
• The gate operator installation is NOT a “do-it-yourself” project. Contract a qualied gate ope-
rator installation company to install this system to ensure a safe and reliable installation.
• It is the responsibility of the property owner to ensure the installer is qualied to carry out the
installation in a safe and professional manner.
• Consult local government agencies for up-to-date rules and regulations to satisfy licensing,
codes or regulations that regulate automated gate system design and installation.
• The gate for which the gate operator is intended to be used should itself be installed correctly
so that it is level and plumb and the gate opens easily and evenly.
• Note that Nice swing gate systems are not intended for installation on an incline.
SECTION 2: INSTALLATION SAFETY
SECTION 3: TOOLS NEEDED FOR INSTALLATION
WARNING!
READ ALL SAFETY INFORMATION WHEN INSTALLING A SWING GATE SYSTEM! SEE EITHER
OF THE FOLLOWING MANUALS FOR SAFETY INFORMATION:
• CBOX936 Control Box Installation Manual (with 936 control board)
• CBOX1050 Control Box Installation Manual (with 1050 control board)
TITAN 912L Actuator
INSTALLATION REFERENCE MANUAL
5
MX4685 Rev. C ©2019 hysecurity.com • 800-321-9947
LEFT SIDE VERTICAL VIEW
IMAGE 1A-1: "PULL TO OPEN" PIVOT ARM INSTALLATION
INSTALL PIVOT ARM TO GATE: PULL-TO-OPEN
1A
1. Securely mount the pivot arm to the hinge post (IMAGE 1A-1).
2. If necessary, cut pivot arm for correct placement of the actuator mounting hole. Measurements are
taken from the center of pivot of the gate hinge (IMAGE 1A-1).
3. It is strongly recommended to weld the pivot arm to the hinge post.
TOP VIEW
6” 6”
13” 13”
SECTION 4: ACTUATOR - MECHANICAL INSTALLATION
NOTE: Welding
is much preferred
but Nice offers an
optional bolt-on
pivot arm (P/N 446)
for when welding is
not possible.
PIVOT ARM PIVOT ARM
PIVOT ARM
1/2”
HINGE POST
CENTER OF HINGE
CENTER LINE OF
ATTACHMENT POINT
FOR GATE BRACKET
CENTER OF HINGE
GATE CLOSED
DIRECTION OF OPENING
CAUTION!
NEVER WELD PARTS TO THE GATE OR POSTS WHEN THE CONTROL BOARD IS
POWERED TO AVOID IRREPAIRABLE DAMAGE TO THE CIRCUIT BOARD!
HINGE POST HINGE POST
TITAN 912L Actuator
INSTALLATION REFERENCE MANUAL
6hysecurity.com • 800-321-9947 MX4685 Rev. C ©2019
IMAGE 1B-1: "PUSH TO OPEN" PIVOT ARM INSTALLATION
1B
1. Securely mount the pivot arm to the hinge post (IMAGE 1B-1).
2. If necessary, cut pivot arm for correct placement of the actuator mounting hole. Measurements are
taken from the center of pivot of the gate hinge (IMAGE 1B-1).
3. It is strongly recommended to weld the pivot arm to the metal post.
INSTALL PIVOT ARM TO GATE: PUSH-TO-OPEN
CAUTION!
NEVER WELD PARTS TO THE GATE OR POSTS WHEN THE CONTROL BOARD IS
POWERED TO AVOID IRREPAIRABLE DAMAGE TO THE CIRCUIT BOARD!
TOP VIEW
6” 6”
11” 11”
PIVOT ARM
PIVOT ARM
PIVOT ARM
1/2”
HINGE POST
CENTER OF HINGE
HINGE POST HINGE POST
CENTER LINE OF
ATTACHMENT POINT
FOR GATE BRACKET
CENTER OF HINGE
GATE CLOSED
DIRECTION OF OPENING
LEFT SIDE VERTICAL VIEW
NOTE: Welding
is much preferred
but Nice offers an
optional bolt-on
pivot arm (P/N 446)
for when welding is
not possible.
TITAN 912L Actuator
INSTALLATION REFERENCE MANUAL
7
MX4685 Rev. C ©2019 hysecurity.com • 800-321-9947
2MOUNT ACTUATOR TO PIVOT ARM
IMAGE 2-1: INSTALLING ACTUATOR TO PIVOT ARM
IMAGE 2-2: ACUATOR LEVEL
IMAGE 2-3: LEVEL ACTUATOR
(GATE CLOSED)
1. Mount actuator to pivot arm as shown in IMAGE 2-1 using 1/2” bolt and lock nut. Tighten until secure.
2. Use bubble level to ensure actuator is level and plumb in both open and closed positions.
1/2”x 3.5” BOLT
ACTUATOR
1/2”LOCK NUT
PIVOT ARM
PIVOT ARM
CABLE
LOOP
LEVEL
LEVEL
LEVEL
LEVEL
IMPORTANT!
• Use a bubble level to ensure pivot arm and actuator
are plumb and level in open and close positions
(IMAGES 2-2 & 2-3).
• Ensure that actuator mounting hardware is tight
enough to prevent movement, vibration, wobble,
or shifting when the actuator is in operation..
• Note cable loop (IMAGE 2-3) to allow strain relief
for cable during actuator movement.
ACTUATOR
TITAN 912L Actuator
INSTALLATION REFERENCE MANUAL
8hysecurity.com • 800-321-9947 MX4685 Rev. C ©2019
AFFIX GATE BRACKET TO ACTUATOR ARM
3
1/2”x 2” PIVOT BOLT
1/2”x 2” PIVOT BOLT
GATE BRACKET
(SIDE VIEW)
GATE BRACKET
ACTUATOR
ARM
1/2” LOCK NUT
WASHER (ZINC)
ACTUATOR
ARM
IMAGE 3-1: AFFIXING GATE BRACKET TO ACTUATOR ARM
IMAGE 3-2: GATE BRACKET HARDWARE REQUIREMENTS
WASHER
WASHER
(STAINLESS STEEL)
LOCK NUT
If the gate bracket is not already installed on the actuator arm, mount gate bracket to actuator arm
with the pivot bolt, nut, and washers per images below.
WASHER
TITAN 912L Actuator
INSTALLATION REFERENCE MANUAL
9
MX4685 Rev. C ©2019 hysecurity.com • 800-321-9947
1. Place gate in:
a) CLOSED position for PUSH-TO-OPEN congurations ( IMAGE 4-1).
b) OPEN position for PULL-TO-OPEN conguration (IMAGE 4-2).
2. With actuator arm fully retracted, rotate entire actuator on the pivot arm around until the gate
bracket attached to the actuator is positioned on a supporting structure of gate.
3. Mark position of gate bracket on gate or clamp into position.
4POSITION GATE BRACKET ON GATE
GATE OPEN (PULL-TO-OPEN)
IMAGE 4-2: PULL-TO-OPEN GATE BRACKET LOCATION
ACTUATOR
PIVOT
ARM
GATE BRACKET
LOCATION
TRAFFIC DIRECTION
ARMATURE FULLY
RETRACTED
WALL
HINGE
HINGE
POST
IMAGE 4-1: PUSH-TO-OPEN GATE BRACKET LOCATION
GATE CLOSED (PUSH-TO-OPEN)
GATE BRACKET
LOCATION
TRAFFIC
DIRECTION
ARMATURE FULLY RETRACTED
WALL
HINGE
POST HINGE
PIVOT ARM
ACTUATOR
TITAN 912L Actuator
INSTALLATION REFERENCE MANUAL
10 hysecurity.com • 800-321-9947 MX4685 Rev. C ©2019
1. Weld the gate bracket to the gate supporting structure (IMAGE 5-1) or use supplied 3/8” bolts
and nuts from kit (IMAGE 5-2).
2. If welding is not possible, drill two holes to match bracket mounting holes and afx with two
3/8”x2.5” screws and 3/8” nuts included in the kit (IMAGE 5-2). Tighten to
IMAGE 5-1: GATE BRACKET WELDED TO GATE
IMAGE 5-2: GATE BRACKET AND HARDWARE (BLACK BRACKET SHOWN)
5AFFIX GATE BRACKET TO GATE
GATE BRACKET
3/8”x2.5” HEX BOLT (x2)
WELD
3/8” NUT (x2)
IMPORTANT! Ensure bracket centerline is 1/2” above the top of the pivot arm.
IMPORTANT! Use a bubble level to assure after mounting that actuator is level and plumb.
CAUTION!
NEVER WELD PARTS TO THE GATE OR POSTS WHEN THE CONTROL BOARD IS
POWERED TO AVOID IRREPAIRABLE DAMAGE TO THE CIRCUIT BOARD!
NOTE:
Attach gate
bracklet only to
structural supports.
If unsure of exact
bracket location,
tack weld or clamp
until gate can be
tested.
This manual suits for next models
2
Table of contents
Popular Controllers manuals by other brands
Digiplex
Digiplex DGP-848 Programming guide
YASKAWA
YASKAWA SGM series user manual
Sinope
Sinope Calypso RM3500ZB installation guide
Isimet
Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions
LSIS
LSIS sv-ip5a user manual
Rockwell Automation
Rockwell Automation 1769-L31 installation instructions
