National Instruments PXIe-8238 User manual
GETTING STARTED GUIDE
PXIe-8238
This document includes instructions for installing and configuring your PXIe-8238 module.
Contents
Products Covered...................................................................................................................... 1
Getting Started.......................................................................................................................... 1
Unpacking......................................................................................................................... 1
Electrical........................................................................................................................... 2
Preparing the Environment............................................................................................... 2
Hardware Installation........................................................................................................2
Powering On the PXIe-8238............................................................................................. 3
Powering Off the PXIe-8238............................................................................................ 3
Software Installation and Configuration........................................................................... 3
PXIe-8238 Front Panel......................................................................................................3
Removing the PXIe-8238 from a PXI Express Chassis....................................................5
Cleaning............................................................................................................................ 5
Common Configuration Questions........................................................................................... 5
General Questions............................................................................................................. 5
Worldwide Support and Services.............................................................................................. 6
Products Covered
This document covers the following products:
• PXIe-8238 (142470x-010L)
Note Following the model number above is the specific NI assembly number in
parentheses. Ensure that the specifications of interest match the NI assembly number
printed on the board. x denotes all letter revisions of the assembly.
Getting Started
This section includes instructions for unpacking and installing your PXIe-8238 module. It also
describes the module's front panel connectors.
Unpacking
The PXIe-8238 ships in an antistatic package to prevent electrostatic discharge from damaging
device components. To prevent such damage when handling the device, ground yourself using
a grounding strap or by holding a grounded object, such as your computer chassis, and
complete the following steps:
1. Touch the antistatic package to a metal part of the chassis before removing the device
from the package.
Caution Never touch the exposed pins of connectors.
2. Remove the device from the package and inspect the device for loose components or any
other sign of damage.
3. Notify National Instruments if the device appears damaged in any way. Do not install a
damaged device into your chassis.
Electrical
Power Rail Typical Value Max Value
+3.3 VDC 0.62 A 0.93 A
+12 VDC 1.02 A 1.68 A
Total Power 14.28 W 23.23 A
Preparing the Environment
Ensure the environment you are using the PXIe-8238 in meets the following specifications.
Ambient temperature range 0 °C to 55 °C (Tested in accordance with
IEC-60068-2-1 and IEC-60068-2-2.)
Relative humidity range 10% to 90%, noncondensing (Tested in
accordance with IEC-60068-2-56.)
Maximum altitude 2,000 m (800 mbar)
Pollution Degree 2
Indoor use only.
Note Refer to the PXIe-8238 User Manual for full PXIe-8238 specifications.
Hardware Installation
The following are general instructions for installing the PXIe-8238.
Complete the following steps to install the PXIe-8238 in your PXI Express chassis.
1. Power off your PXI Express chassis, but leave it plugged in while installing the
PXIe-8238. The power cord grounds the chassis and protects it from electrical damage
while you install the module.
Caution To protect both yourself and the chassis from electrical hazards,
leave the chassis off until you finish installing the PXIe-8238.
2. Remove or open any doors or covers blocking access to the slot in which you intend to
install the PXIe-8238.
2| ni.com | PXIe-8238 Getting Started Guide
3. Touch a metal part of the chassis to discharge any static electricity that might be on your
clothes or body.
4. Make sure the injector/ejector handle is in its downward position. Be sure to remove all
connector packaging and protective caps from retaining screws on the module.
5. Identify the slot in which the PXIe-8238 will be installed in the chassis. Refer to the
following table to determine which slot types the PXIe-8238 is compatible with.
Table 1. PXIe-8238 Slot Type Compatibility
NI PXI Express Product
PXI Express Chassis
Controller Peripheral Hybrid
H
PXIe-8238 — ✓ ✓
6. Align the PXIe-8238 with the card guides on the top and bottom of the slot. Hold the
handle as you slowly slide the module into the chassis until the handle catches on the
injector/ejector rail.
Caution Do not raise the injector/ejector handle as you insert the PXIe-8238.
It will not insert properly unless the handle is in its downward position so that it
does not interfere with the injector/ejector rail on the chassis.
7. Raise the injector/ejector handle until the module firmly seats into the backplane
receptacle connectors. The front panel of the PXIe-8238 should be even with the front
panel of the chassis.
8. Tighten the bracket-retaining screws on the top and bottom of the front panel to secure
the PXIe-8238 to the chassis.
9. Replace or close any doors or covers to the chassis.
Powering On the PXIe-8238
The PXIe-8238 powers on automatically when the chassis is powered on. To power on the
PXIe-8238, turn on the chassis.
Powering Off the PXIe-8238
The PXIe-8238 powers off automatically when the chassis is powered off. You also can power
off the PXIe-8238 by shutting down the system controller.
Software Installation and Configuration
The PXIe-8238 requires driver software to enable its features. For software installation
instructions, go to ni.com/downloads, enter PXIe-8238 in the Downloads text box, and click
the search button.
PXIe-8238 Front Panel
The following figure shows the front panel layout of the PXIe-8238.
PXIe-8238 Getting Started Guide | © National Instruments | 3
Figure 1. PXIe-8238 Front Panel
NI PXIe-8238
ETH 0
LINK/ACT
LINK/ACT
SPEED
SPEED
ETH 1
2
3
2
3
1
1. Ethernet Connector
2. LINK/ACT LED
3. SPEED LED
Front Panel Connectors
The following table lists various peripherals and their corresponding PXIe-8238 external
connectors, bus interfaces, and functions.
Peripheral External Connector Description
Ethernet Port SFP+ 1 Gb/10 Gb Ethernet based on Intel 82599 10 GbE
controller
Note For optimum performance, the chassis must have at minimum a Gen2 x8
peripheral slot (for example, the PXIe-1085).
4| ni.com | PXIe-8238 Getting Started Guide
Front Panel Features
The PXIe-8238 has the following front-panel features:
• Two front panel LEDs per port that show status:
–LINK/ACT— The Link/Activity LED indicates one of the following states:
• No link: off
• Linked - no activity: green
• Linked - activity: blinking green
–SPEED— The Speed LED indicates one of the following states:
• No link: off
• Linked - no activity: yellow = 1 GbE, green = 10 GbE
• Linked - activity: yellow = 1 GbE, green = 10 GbE
Removing the PXIe-8238 from a PXI Express Chassis
To remove the PXIe-8238 from a PXI Express chassis, complete the following steps.
1. Power off the chassis.
2. Remove any cables that may be attached to the module front panel.
3. Unscrew the two bracket-retaining screws in the front panel.
4. Press the injector/ejector handle down.
5. Slide the module out of the chassis.
Cleaning
Use a dry, low-velocity stream of air to clean the PXIe-8238 module. If needed, use a soft,
nonmetallic brush for cleaning around components.
Make sure the module is completely dry and free from contaminants before returning it to
service.
Common Configuration Questions
This section answers common configuration questions you may have when using a PXIe-8238
module.
General Questions
What do the LEDs on the front panel mean?
Refer to the LED status descriptions in the Front Panel Features section.
My system boots fine as long as a particular module is not in my
chassis.
The most common cause of this is a damaged module. Try the module in a different chassis or
with a different controller. Also, remove any external cables or terminal blocks connected to
PXIe-8238 Getting Started Guide | © National Instruments | 5
the system. If the module does not work in these cases, it is likely damaged. Contact the
module manufacturer for further troubleshooting.
Refer to the KnowledgeBase at ni.com/kb or product manuals section at ni.com/manuals for
more information specific to the module with which you are having difficulties.
Worldwide Support and Services
The NI website is your complete resource for technical support. At ni.com/support, you have
access to everything from troubleshooting and application development self-help resources to
email and phone assistance from NI Application Engineers.
Visit ni.com/services for NI Factory Installation Services, repairs, extended warranty, and
other services.
Visit ni.com/register to register your NI product. Product registration facilitates technical
support and ensures that you receive important information updates from NI.
A Declaration of Conformity (DoC) is our claim of compliance with the Council of the
European Communities using the manufacturer’s declaration of conformity. This system
affords the user protection for electromagnetic compatibility (EMC) and product safety. You
can obtain the DoC for your product by visiting ni.com/certification. If your product supports
calibration, you can obtain the calibration certificate for your product at ni.com/calibration.
NI corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas,
78759-3504. NI also has offices located around the world. For telephone support in the United
States, create your service request at ni.com/support or dial 1 866 ASK MYNI (275 6964). For
telephone support outside the United States, visit the Worldwide Offices section of ni.com/
niglobal to access the branch office websites, which provide up-to-date contact information,
support phone numbers, email addresses, and current events.
Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for information on National Instruments trademarks.
Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents
covering National Instruments products/technology, refer to the appropriate location: Help»Patents in your software, the
patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents. You can find information about
end-user license agreements (EULAs) and third-party legal notices in the readme file for your NI product. Refer to the Export
Compliance Information at ni.com/legal/export-compliance for the National Instruments global trade compliance policy and
how to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES
AS TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS.
U.S. Government Customers: The data contained in this manual was developed at private expense and is subject to the
applicable limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.
© 2017 National Instruments. All rights reserved.
376805A-01 May2017
Other manuals for PXIe-8238
2
Table of contents
Other National Instruments Control Unit manuals
National Instruments
National Instruments ISM-7400 User manual
National Instruments
National Instruments PXIe-8245 User manual
National Instruments
National Instruments SCXI SCXI-1102 Installation and operating instructions
National Instruments
National Instruments SCXI Series User manual
National Instruments
National Instruments PXIe-4302 User manual
National Instruments
National Instruments Module SCXI-1503 Manual
National Instruments
National Instruments NI 9234 User manual
National Instruments
National Instruments NI 9469 User manual
National Instruments
National Instruments SCC-DO01 User manual
National Instruments
National Instruments PXIe-8240 User manual
National Instruments
National Instruments NI 9265 User manual
National Instruments
National Instruments NI 9871 User manual
National Instruments
National Instruments PXIe-5698 User manual
National Instruments
National Instruments SCC-LP Series User manual
National Instruments
National Instruments NI 9436 User manual
National Instruments
National Instruments NI USB-9201 User manual
National Instruments
National Instruments VXI-8340 Series User manual
National Instruments
National Instruments 9756 User manual
National Instruments
National Instruments NI 9882 User manual
National Instruments
National Instruments SC Express PXIe-4330 Manual
Popular Control Unit manuals by other brands
Festo
Festo Compact Performance CP-FB6-E Brief description
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Quick installation guide
JS Automation
JS Automation MPC3034A user manual
JAUDT
JAUDT SW GII 6406 Series Translation of the original operating instructions
Spektrum
Spektrum Air Module System manual
BOC Edwards
BOC Edwards Q Series instruction manual
KHADAS
KHADAS BT Magic quick start
Etherma
Etherma eNEXHO-IL Assembly and operating instructions
PMFoundations
PMFoundations Attenuverter Assembly guide
GEA
GEA VARIVENT Operating instruction
Walther Systemtechnik
Walther Systemtechnik VMS-05 Assembly instructions
Altronix
Altronix LINQ8PD Installation and programming manual
