National Instruments PXIe-4302 User manual

USER GUIDE AND TERMINAL BLOCK

SPECIFICATIONS

NI PXIe-4302/4303 and

TB-4302/4302C

32 Ch, 24-bit, 5 kS/s or 51.2 kS/s Simultaneous Filtered Data

Acquisition Module

This document explains how to install, configure, and set up the NI PXIe-4302 and

NI PXIe-4303 (NI PXIe-4302/4303) simultaneous filtered modules with the TB-4302 and

TB-4302C terminal blocks. Driver support for the NI PXIe-4302/4303 was first available in

NI-DAQmx 15.1. For the list of devices supported by a specific release, refer to the NI-DAQmx

Readme, available on the version-specific download page or installation media.

Note The keying of these terminal blocks prevents them from connecting to other

modules that could be damaged by the voltage present on the terminal block.

However, you should only use these terminal blocks with their supported modules.

Contents

Electromagnetic Compatibility Guidelines .............................................................................. 2

What You Need to Get Started ................................................................................................. 3

Installation ................................................................................................................................ 3

Install the Software........................................................................................................... 3

Unpack and Install the Module......................................................................................... 4

Connect the Signals .......................................................................................................... 5

Install the Terminal Block ................................................................................................ 8

Confirm NI PXIe-4302/4303 Module Recognition.......................................................... 10

Run Test Panels ................................................................................................................ 11

Take an NI-DAQmx Measurement .................................................................................. 11

NI-DAQmx Channels and Tasks.............................................................................. 11

Configure a Task Using the DAQ Assistant in MAX .............................................. 11

Use Your NI PXIe-4302/4303 Module in an Application................................................ 12

Programming Examples ........................................................................................... 12

Terminal Block Removal..........................................................................................................13

Module Removal ...................................................................................................................... 14

Create a Simulated Device .......................................................................................................15

2|ni.com |NI PXIe-4302/4303 and TB-4302/4302C

Cold-Junction Compensation (TB-4302 Only)......................................................................... 15

Minimizing Thermal Gradients ................................................................................................ 15

More Information...................................................................................................................... 16

Troubleshooting ................................................................................................................ 16

Specifications (TB-4302/4302C)..............................................................................................16

Calibration Interval ...................................................................................................................17

Electrical ................................................................................................................................... 17

TB-4302 ............................................................................................................................17

TB-4302C ......................................................................................................................... 17

Mechanical........................................................................................................................ 17

Physical .............................................................................................................................18

Environmental Specifications ...........................................................................................18

Operating Environment............................................................................................. 18

Storage Environment ........................................................................................................19

Shock and Vibration .........................................................................................................19

Safety ................................................................................................................................19

Safety Standards ...............................................................................................................19

Electromagnetic Compatibility ......................................................................................... 20

CE Compliance ................................................................................................................. 20

Online Product Certification............................................................................................. 20

Environmental Management............................................................................................. 21

World Wide Support and Services............................................................................................ 21

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits for

electromagnetic compatibility (EMC) stated in the product specifications. These requirements

and limits provide reasonable protection against harmful interference when the product is

operated in the intended operational electromagnetic environment.

This product is intended for use in industrial locations. However, harmful interference may

occur in some installations, when the product is connected to a peripheral device or test object,

or if the product is used in residential or commercial areas. To minimize interference with radio

and television reception and prevent unacceptable performance degradation, install and use this

product in strict accordance with the instructions in the product documentation.

Furthermore, any modifications to the product not expressly approved by National Instruments

could void your authority to operate it under your local regulatory rules.

Caution To ensure the specified EMC performance, operate this product only with

shielded, twisted pair cables and shielded accessories.

Caution To ensure the specified EMC performance, the length of all I/O cables

must be no longer than 30 m (100 ft).

NI PXIe-4302/4303 and TB-4302/4302C |© National Instruments |3

What You Need to Get Started

To set up and use a NI PXIe-4302/4303 module with a TB-4302/4302C terminal block, you need

the following items:

Hardware

– NI PXIe-4302/4303 module

– TB-4302/4302C terminal block

– NI PXI Express chassis

– Cabling and sensors as required for your application

Tools

– Number 1 and 2 Phillips-head screwdrivers

– 1/8 in. flathead screwdriver

– Long-nose pliers

– Wire cutter

– Wire insulation stripper

Documentation

–Read Me First: Safety and Electromagnetic Compatibility

– NI PXIe-4302/4303 and TB-4302/4302C User Guide and Terminal Block

Specifications

–NI PXIe-4302/4303 User Manual

– NI PXI Express chassis user manual

You can download needed documents from ni.com/manuals.

Installation

Install the Software

Note You must be an administrator to install NI software and devices on your

computer.

Ensure that the following software is installed before installing the NI PXIe-4302/4303 and

TB-4302/4302C hardware:

1. Your application software, such as LabVIEW, LabWindows™CVI™or .NET.

2. NI-DAQmx—NI PXIe-4302/4303 modules were first supported in NI-DAQmx 15.1.

Note For detailed NI software version support, refer to the NI-DAQmx Readme.

Back up any applications before upgrading software or modifying the application.

4|ni.com |NI PXIe-4302/4303 and TB-4302/4302C

Unpack and Install the Module

Remove the packaging and inspect the module. Contact NI if the module is damaged. Do not

install a damaged module.

Caution The module is static sensitive. Always properly ground yourself and the

equipment when handling or connecting to the module.

Complete the following steps to install the NI PXIe-4302/4303 module while referring to

Figures 1 and 2:

Note To maintain forced air cooling in the PXIe system, refer to the Maintain

Forced-Air Cooling Note to Users.

1. Plug in your chassis before installing the NI PXIe-4302/4303. The power cord grounds the

chassis and protects it from electrical damage while you install the module.

2. Make sure the chassis is powered off.

Caution To protect yourself, the chassis, and the NI PXIe-4302/4303 from

electrical hazards, leave the chassis powered off until you finish installing the

NI PXIe-4302/4303 module.

3. Touch a metal part on the chassis to discharge any accumulated static electricity.

4. Identify a supported PXI Express slot in the chassis. NI PXIe-4302/4303 modules can be

placed only in PXI Express Peripheral slots, PXI Express Hybrid Peripheral slots, and PXI

Express System Timing slots. Refer to the chassis documentation for details.

Figure 1. Symbols for PXI Express/ PXI Express Hybrid/ PXI Slots

5. Remove the filler panel, and touch any metal part of the chassis to discharge static

electricity.

6. Place the module edges into the module guides at the top and bottom of the slot.

Caution When installing the module, make sure both edges are positioned inside

the guides and that the module components do not come into contact with adjacent

modules.

1 PXI Express System Controller Slot

2 PXI Peripheral Slot

3 PXI Express Hybrid Peripheral Slot

4 PXI Express System Timing Slot

NI PXIe-1062Q

1 2 34

NI PXIe-4302/4303 and TB-4302/4302C |© National Instruments |5

7. Slide the module along the guides until it reaches the rear connector then seat the module

by pushing the front panel until it is flush with the front panel of the chassis.

8. Secure the module to the chassis using the front-panel captive screws, shown in Figure 2.

Tighten the screws to 0.31 N ·m (2.7 lb · in.).

Figure 2. Installing NI PXIe-4302/4303 Modules

Connect the Signals

Caution For EMC compliance, operate this product with shielded cables and

accessories.

To connect signals to the terminal block, refer to Figures 3 and, 4 or 5 while completing the

following steps:

Note You can find the pinout names and locations in Measurement & Automation

Explorer (MAX) at any time by right-clicking the device name under Devices and

Interfaces and selecting Device Pinouts.

1. Loosen the captive top cover screws and remove the top cover.

2. Loosen the strain-relief screws and remove the strain-relief bar.

3. Prepare the shielded signal wire by stripping the insulation no more than 7 mm (0.28 in.).

1CaptiveScrews

NI PXIe-1062Q

COOLING CLEARANCE AND FANFILTER MAINTENANCE REQUIRED.SEEMANUAL.

6|ni.com |NI PXIe-4302/4303 and TB-4302/4302C

4. Run the shielded signal wires through the strain-relief opening.

Figure 3. TB-4302/4302C Parts Locator Diagram

5. Insert the stripped end of the shielded signal wires fully into the appropriate terminal. Refer

to the label next to each screw terminal to determine the function of the terminal. The

NI PXIe-4302/4303 User Manual provides more detailed wiring information. Make sure no

exposed wire extends past the screw terminal. Exposed wire increases the risk of a short

circuit that can cause circuit failure.

1 Strain-Relief Screws

2 Strain-Relief Bar

3 Tie Wrap Holes

4 Ground Lugs

5 Terminal Block to Module Connector

6 Captive Top Cover Screws

7 Top Cover

8 Tie Wraps

9 Shielded Signal Wires

1 2

NI PXIe-4302/4303 and TB-4302/4302C |© National Instruments |7

Figure 4. TB-4302 Circuit Board Parts Locator Diagram

Figure 5. TB-4302C Circuit Board Parts Locator Diagram

Note Refer to the NI PXIe-4302/4303 User Manual for wiring diagrams showing

how to connect sensors to the TB-4302/4302C.

6. Tighten the terminal screws to a torque of 0.2 to 0.25 N · m (1.77 to 2.21 lb · in.).

AI3-

AI3+

AI2+

AI4+

AI4-

AI5-

AI7-

AI7+

AI6-

AI6+

AI5+

AI0+

AI0-

AI1-

AI2+

AI1+

AI9+

AI9-

AI10+

AI13+

AI13-

AI14+

AI15+

AI15-

AI14-

AI12+

AI11+

AI10-

AI8+

AI11-

AI8-

AI12-

AI7+

AI7-

AI18+

AI21+

AI21-

AI22+

AI23+

AI23-

AI22-

AI20+

AI19+

AI18-

AI6+

AI19-

AI6-

AI20-

AI5+

AI5-

AI16+

AI29+

AI29-

AI30+

AI31+

AI31-

AI30-

AI28+

AI17+

AI16-

AI4+

AI17-

AI4-

AI28-

FOR PATENTS: NI.COM/PATENTS

NI TB-4302

S/N

158016B-01L

UL94V-0

AIGND AIGND

J21J4188

J6 J8

J10 J121818

8181

CR3

AIGND AIGND

J15

J17

J11 J13 J18

J16J14

8181

R5 R6 R4

CR1

CR2

PFI0

DGND

FOR PATENTS: NI.COM/PATENTS

AI3

VSUP

AI2

VSUP

AI4

AI5

AI7

VSUP

AI6

VSUP

AI0

AI1

VSUP

AI2

VSUP

AI1

VSUP

AI3

AI4

AI15

VSUP

AI8

VSUP

AI0

VSUP

AI19

VSUP

AI18

VSUP

AI20

AI21

AI23

VSUP

AI22

VSUP

AI16

AI17

VSUP

AI28

VSUP

AI27

VSUP

AI29

AI30

AI31

VSUP

AI24

VSUP

A25

AI26

VSUP

S/N

158141A-01L

NI TB-4302C

GND

PFI0

AISENSE

AIGND

AISENSE

VSUP

J2 J4

J3 J7 J5 J9

J21

J19 J10

J15 J11 J17

U9 U11 U10 J12

J13 J18

J16

J14

CR3

8|ni.com |NI PXIe-4302/4303 and TB-4302/4302C

Caution Any wires connected to the ground must be sufficiently insulated from

high voltage.

7. Use the ground lugs to attach a shield wire to the ground.

Note Refer to the NI PXIe-4302/4303 User Manual for details about shielding the

signals.

8. Reinstall the strain-relief bar and tighten the strain-relief screws.

9. Use tie wraps to connect the shielded signal wires to the tie-wrap holes for additional strain

relief when necessary.

10. Reinstall the top cover and tighten the captive top cover screws.

Note For information about sensors, go to ni.com/sensors.

Install the Terminal Block

Refer to Figure 6 to install the terminal block on the module while completing the following

steps:

1. Move the TB-4302/4302C into position in front of the NI PXIe-4302/4303 and engage the

alignment feature with the guide on the associated module.

Figure 6. Installing the TB-4302/4302C on the NI PXIe-4302/4303 Module

1 PXIe Controller

2 PXIe Chassis

3 Mounting Screw

4 TB-4302/4302C Terminal Block

5 NI PXIe-4302/4303 Module

6 Alignment Feature

NI PXIe-1062Q

COOLINGCLEARANCEANDFANFILTERMAINTENANCEREQUIRED.SEE MANUA L.

COOLING CLEARANCEAND FANFILTER MAINTENANCE REQUIRED.SEEMANUAL.

NI PXIe-4302/4303 and TB-4302/4302C |© National Instruments |9

2. Attach the TB-4302/4302C to the NI PXIe-4302/4303 module by pushing the terminal

block straight into the module. A spring mechanism will lock in the bottom of the terminal

block.

3. Tighten the mounting screw at the top of the TB-4302/4302C to attach it to the

NI PXIe-4302/4303 module.

Note For safety purposes and to prevent damage to equipment when high voltages

are present, all NI PXIe-4302/4303 modules and TB-4302/4302C terminal blocks are

keyed to prevent connection between incompatible terminal blocks, modules, and/or

cables.

4. Power on the chassis.

Figure 7 shows an example NI PXIe-4302/4303 system setup.

Figure 7. Sample NI PXIe-4302/4303 System

1 Terminal Block 2 Signal Input

NI PXIe-1062Q

COOLING CLEARANCE AND FAN FILTER MAINTENANCE REQUIRED.SEE MANUAL.

COOLING CLEARANCE AND FANFILTERMAINTENANCE REQUIRED.SEE MANUAL.

10 |ni.com |NI PXIe-4302/4303 and TB-4302/4302C

Confirm NI PXIe-4302/4303 Module Recognition

To confirm module recognition, complete the following steps:

Note Software support for the NI PXIe-4302/4303 is provided by NI-DAQmx. The

DAQ Getting Started Guide, which you can download at ni.com/manuals, offers

step-by-step NI-DAQmx instructions for installing software and hardware,

configuring channels and tasks, and getting started developing an application. For

detailed NI software version support, refer to the NI-DAQmx Readme.

1. Launch MAX.

2. Expand Devices and Interfaces, and expand the chassis in which the module is located to

confirm that MAX detects the module and terminal block. The terminal block should

appear beneath its associated module. If your module or terminal block is not listed, press

<F5> to refresh MAX. If the module is still not recognized, go to ni.com/support/

daqmx.

Tip Using an NI-DAQmx simulated device, you can test NI-DAQmx applications

without installing hardware. Refer to the Create a Simulated Device section for

instructions for creating NI-DAQmx simulated devices.

3. Right-click the module name and select Self-Test. When the self-test completes, a

verification message appears. If an error occurs, refer to ni.com/support/daqmx.

For information about sensors, go to ni.com/sensors.

Other manuals for PXIe-4302

This manual suits for next models

Table of contents

Other National Instruments Control Unit manuals

National Instruments

National Instruments 7340 PCI User manual

National Instruments

National Instruments SCXI SCXI-1102 User manual

National Instruments

National Instruments NI 9221 User manual

National Instruments

National Instruments NI FlexRIO PXIe-7971R User manual

National Instruments

National Instruments sbRIO-9651 Guide

National Instruments

National Instruments NI 9242 User manual

National Instruments

National Instruments NI-9361 Manual

National Instruments

National Instruments SCXI -1122 Manual

National Instruments

National Instruments FieldPoint FP-2000 User manual

National Instruments

National Instruments 9221 User manual

National Instruments

National Instruments SCXI-1000 User manual

National Instruments

National Instruments FieldPoint FP-DI-301 User manual

National Instruments

National Instruments PXIe-8245 User manual

National Instruments

National Instruments SCC-AI Series User manual

National Instruments

National Instruments SCXI-1104/C Manual

National Instruments

National Instruments NI 9516 User manual

National Instruments

National Instruments SCC-FT01 User manual

National Instruments

National Instruments LabVIEW Robotics Module User manual

National Instruments

National Instruments NI PCIe-1430 User manual

National Instruments

National Instruments NI 9209 Manual

National Instruments

National Instruments SCXI-1000 User manual

National Instruments

National Instruments FIeldPoint FP-AO-200 User manual

National Instruments

National Instruments NI 9861 User manual

National Instruments

National Instruments PXIe-4357 Manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual